Metra Electronics 95-7510 Manuale utente

INSTALLATION INSTRUCTIONS FOR PART 95-7510

95-7510/

95-7510HG

APPLICATIONS

Mazda RX-8

2004-2008

KIT FEATURES

•Double DIN Radio Provision

•Stacked ISO Mount Units Provision

• TWO FINISHES AVAILABLE:

99-7510=BLACK, 99-7510HG=GLOSS BLACK

•A) Radio / Climate Control Housing • B) Double DIN Radio Brackets • C) Rear Support

•D) Interface • E) Wiring Harnesses • F) (2) Climate Control Extension Harnesses

KIT COMPONENTS

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

•Phillips Screwdriver • Socket Set • Cutting Tool

1-800-221-0932

www.metraonline.com

Dash Disassembly

MazdaRX-82004-2008 .........................

. . .1,2,3

Kit Assembly

-Double DIN Radio Provision / Stacked ISO Mount Units Provision . . . . 4

Final Assembly .........................................5,6

Display Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

TABLE OF CONTENTS

95-7510

*Note:

Refer also to the instructions included with the aftermarket radio.

NOWLEDGE IS

OWER

Enhanceyour installation and fabrication skillsby

enrolling in the most recognizedandrespected

mobile electronics school in our industry.

Log onto www.installerinstitute.comor call

800-354-6782 for more informationandtake steps

toward abetter tomorrow.

95-7510 DASH DISASSEMBLY

MAZDARX-8 2004-2008

FM1 877

Unclip and remove the shifter trim

panel. (

Figure B)

Disconnect the negative battery ter-

minal to prevent an accidental short

circuit.

Unscrew the shift knob counter clock-

wise to remove. (

Figure A)

Remove (2) Phillips screws from the

bottom of the ashtray assembly then

unclip and remove the assembly.

(

Figure C)

Unclip and remove the knee panel on

the driver’s side under the steering

column (

Figure D)

then remove (1) 10

MM bolt from the side of the radio

bracket. (

Figure E)

Continued on page 2.

95-7510 DASH DISASSEMBLY

MAZDARX-8 2004-2008

FM1 877

Remove (3) Phillips screws securing

the factory display harness to the

radio chassis. Unplug and remove

display harness. (Retain display har-

ness for re-use during kit assembly.)

(

Figure H)

Remove (2) Phillips screws from the

bottom of the radio/climate control

panel. (

Figure F)

Unsnap radio/climate control panel

including radio chassis. Unplug and

remove panel and chassis. (

Figure G)

Remove (4) screws securing the radio

chassis to the radio/climate control

panel. (

Figure I)

Remove (6) screws securing the cli-

mate controls from the radio/climate

control panel. Unplug and remove the

climate controls. (Retain the screws

and climate controls for re-use during

kit assembly.) (

Figure J)

Continued on page 3.

95-7510 DASH DISASSEMBLY

MAZDARX-8 2004-2008

REMOVE (2) SCREWS PER SIDE

Remove (17) screws securing the cir-

cuit board to the radio/climate control

panel to access the plug for the haz-

ard switch assembly. (

Figure K)

Remove (2) screws securing the haz-

ard switch to the radio/climate control

panel. Unplug and remove hazard

switch. (Retain the screws and hazard

switch for re-use during kit assem-

bly.) (

Figure L)

Continue to kit assembly.

95-7510 KIT ASSEMBLY

DOUBLE DIN RADIO PROVISION OR

STACKED ISO MOUNT UNITS PROVISION

Cut the top (2) mounting locations off

of the climate controls to provide

clearance for the aftermarket radio.

(Figure A)

Secure the climate control to the

radio/climate control housing using (4)

of the factory screws removed in step

(10) of the dash disassembly.

(Figure B)

Secure the hazard switch assembly to

the radio/climate control housing using

the factoryscrews removed in step

(12).

(Figure B)

Attach the Double DIN brackets to the

Double DIN or stacked ISO Mount

unit(s) using the hardware supplied

with the unit(s).

(Figure C)

Attachthe rear support to the unit(s)

using the hardware supplied with the

unit(s).

(Figure D)

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

A/C

95-7510 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

FINAL WIRING CONNECTIONS

METRA / EIA WIRING CODE

12V Ignition / Acc. . . . . . Red

12V Batt / Memory . . . . . Yellow

Ground . . . . . . . . . . . . . . Black*

Power Antenna . . . . . . . . Blue

Amp Turn-On . . . . . . . . . Blue / White

Amp Ground . . . . . . . . . . Black / White

Illumination . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . Gray

Right Front (-). . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . White

Left Front (-) . . . . . . . . . . White / Black

Right Rear (+). . . . . . . . . Violet

Right Rear (-) . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.

All colors may not be present on all leads due to manufacturer’sspecifications.

Locate the factory wiring harness in the dash. Use the supplied wire harnesses and

make the connections as shown. (Isolate and individually tape off the ends of any

unused wires to prevent electrical short circuit). Refer to Metra/EIA Wiring Code

below.

Makewiring connections using the EIA color code chart shown below and the

instructions included with the head unit. Metra recommends making connections as

shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any

unused wires to prevent electrical short circuit.

Continued on Page 6

95-7510 FINAL ASSEMBLY

WARNING!

FAILURE TO INSERT THE HVACCABLES INTO THE CORRECT

LOCATION WILL CAUSE DAMAGE TO THE INTERFACE AND MAKE

THE DISPLAY AND HVACCONTROLS NOT FUNCTION PROPERLY

Plug the Temperature Control cable from the factory climate control into the port

on the interface that reads “TEMP”.

Plug the Fan Control cable from the factory climate control into the port on the

interface that reads “FAN”.

Plug the Display cable removed in step 8 of the dash disassembly into the port

on the interface that reads “DISP”.

Attach the (2) climate control extension harnesses to the temperature control

cable and the fan control cable on the factory climate control.

Plug the HazardSwitch extension cable into the end of the hazardswitchand

the other end of the extension cable into the port next to the “DISP” port.

Continued on Page 7

Continued from Page 5

When using the Navfeatures of the interface you will need to connect the 2 pin

harness and run the 2 wires to the OBDII connector and connect them in the

position shown.

(Figure A)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

The following wires on the 10 pin harness are for the aftermarket radios that have navigation built in:

A. Connect the green wire to the parking brake wire of the aftermarket navigation radio.

B. Connect the pink /blue wire to the VSS or speed sense wire of the aftermarket navigation radio.

C. Connect the green/purple wire to the reverse wire of the aftermarket navigation radio.

NOTE:

Reverse output is NOT present on manual transmission vehicles.

12345678

9 10 11 12 13 14 15 16

PINK WIRE

OBDII CONNECTOR FACE VIEW

PINK/BLUE WIRE

95-7510 FINAL ASSEMBLY

Continued from Page 6

95-7510 KIT ASSEMBLY

DISPLAY CUSTOMIZATION

Press and hold the A/C Mode button to scroll through the various kit options (AMB

TEMP ON or OFF, AMB TEMP C or F, SET TIME 12/24H, and SET TEXT).

When you see the option you want just let the button go and the action on the

screen will be performed. (ie: To turn the ambient temperature on you would scroll

through until the display says “AMB TEMP ON” and let the button go.)

To set the time hold down the A/C Mode button until the display says “SET TIME

12/24H” then let the button go.

To switch between 12H and 24H press the front defrost button to the left of the

A/C Mode button.

To change the Hour press the rear defrost button to the right of the A/C Mode

button.

To change the minute press the A/C button at the top of the A/C Mode button.

At any time if you do not press any buttons for 5 seconds the display will save and

return to the default screen and the climate control buttons will return to their

normal configuration.

If you hold the A/C Mode buttondown long enough the display will say “SET

TEXT”. This will allowyou customize the default text on the display.

Once the display says “SET TEXT” let go and the first letter of the display will begin

blinking.

Press the front defrost button to move the cursor left and the rear defrost button

to move the cursor to the right.

You can scroll up with the A/C button and down with the Recirc/Fresh button

through the various alpha, numeric, and symbol characters.

When you are finished entering your text if you do not press any buttons for 5 sec-

onds the display will save and returnto the default screen and the climate control

buttons will return to their normal configuration.

*Note: Refer also to the instructions included with the aftermarket radio.

FM1 877

OPEN

TILT

A/C

MODE

FM1 877

OPEN

TILT

A/C

MODE

Altri manuali per 95-7510

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Metra Electronics Accessori per automobili

Metra Electronics

Metra Electronics 99-7899 Manuale utente

Metra Electronics

Metra Electronics 99-1003 Manuale utente

Metra Electronics

Metra Electronics GMOS-LAN-04 Manuale utente

Metra Electronics

Metra Electronics 99-7314 Manuale utente

Metra Electronics

Metra Electronics 99-9100 Manuale utente

Metra Electronics

Metra Electronics 99-7001 Manuale utente

Metra Electronics

Metra Electronics 99-5834CH Manuale utente

Metra Electronics

Metra Electronics 99-3014G Manuale utente

Metra Electronics

Metra Electronics 99-6503 Manuale utente

Metra Electronics

Metra Electronics 99-3012G-LC Manuale utente

Metra Electronics

Metra Electronics 108-FD7B Manuale utente

Metra Electronics

Metra Electronics 95-8224 Manuale utente

Metra Electronics

Metra Electronics 99-7504 Manuale utente

Metra Electronics

Metra Electronics 99-6540 Manuale utente

Metra Electronics

Metra Electronics 109-TO7 Manuale utente

Metra Electronics

Metra Electronics 99-7893 Manuale utente

Metra Electronics

Metra Electronics 99-7950 Manuale utente

Metra Electronics

Metra Electronics GMRC-02 Manuale utente

Metra Electronics

Metra Electronics ACURA 99-7866 Manuale utente

Metra Electronics

Metra Electronics 99-6511 Manuale utente

Metra Electronics

Metra Electronics 95-7340B Manuale utente

Metra Electronics

Metra Electronics METRA 99-7603 Manuale utente

Metra Electronics

Metra Electronics JP-RGBKT-1 Manuale utente

Metra Electronics

Metra Electronics 99-5027 Manuale utente

Manuali Accessori per automobili popolari di altre marche

James Baroud

James Baroud Odyssey Manuale utente

Motorola

Motorola i50sx Manuale utente

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuale utente

Feniex

Feniex T3 Manuale utente

Renault

Renault 77 11 423 180 Manuale utente

Kia

Kia E8300-4D000 Manuale utente

Brink

Brink 756843 Manuale utente

Whispbar

Whispbar K085W Manuale utente

v.link

v.link CI-VL2-PC-HSD Manuale utente

Viking

Viking Stack-Rack Guida rapida alla configurazione

Aries

Aries 203015 Manuale utente

Choetech

Choetech AT0005 Manuale utente

ZZ2

ZZ2 ZZAIR-PRO Manuale utente

Holman

Holman 4A80L Manuale utente

Thule

Thule 2075 Manuale utente

Motorola

Motorola T325 Manuale utente

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guida all'installazione

DV8

DV8 FBJL-02 Manuale utente