Mi-Light fullwat LENNY-PAN-B0 Manuale utente
touch panel - 1 ZONE control
LENNY-PAN-B0
Owners manual
by
Smart LED control system
New smart LED color control system with 2.4GHz remote control.
Auto synchronisation and auto transmission functions.
The device adopts low power consumption technologies
and one controller can manage several receivers at the same time.
The system does not produce interference as it uses a very low level transmission signal.
Suitable for simple installations in both domestic and professional environments.
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
2
Technical specifications .................................................................................... 3
Single color ........................................................................................................ 5
Touch panel functions
Mobile control
Tunable white ..................................................................................................... 6
Touch panel functions
Mobile control
RGB .................................................................................................................... 7
Touch panel functions
Mobile control
RGBW ................................................................................................................. 9
Touch panel functions
Mobile control
RGBWW .............................................................................................................. 11
Touch panel functions
Mobile control
Led Strip-controller connection .......................................................................... 13
List of LENNY-DRV-LS2 modes and functions for RGB / RGBW / RGBWW ................ 15
List of LENNY-DRV-WL5 modes and functions for RGB / RGBW / RGBWW............... 15
System linking and unlinking ............................................................................. 16
Device auto-sync ............................................................................................... 17
Auto-transmitting function ................................................................................. 17
Installation diagram
........................................................................................... 18
Mobile phone pairing ........................................................................................ 20
Alexa linking ....................................................................................................... 24
Google Home linking ......................................................................................... 25
Google Assistant linking...................................................................................... 26
Compatibility table
........................................................................................... 27
Table of controls by zones .................................................................................. 28
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
3
Technical specifications
Touch panel
Model LENNY-PAN-B0
Voltage 3V (2 AAA batteries)*
Emitting power 6dBm
Standby current 20uA
Working temperature -10~40°C
Working frequency 2.4GHz
Aprox. operational distance 30m
* Not included.
16
86
86
by
DIRECT CURRENT DRIVERS
LENNY-DRV-LS2 LENNY-DRV-WL5 LENNY-DRV-WL2P
Description 5 in 1 receiver WiFi 5 in 1 receiver WiFi 2 in 1 receiver
Voltage DC12V~24V (terminal block & jack plug inputs)
Output max. current 6A per channel 12A per channel
Total current 15A 12A
Working temperatue -20~60°C -10~40°C
Working frequency 2.4GHz
Aprox. operational distance 30m
Connection mode Common anode
WIFI Requires gateway
LENNY-WIFOX1 Included
23
124
38
SwitchIndicator light
Made in PRC
INPUT
V+RGBCW
V+RGBW
V+RGB
V+CWCW
OUTPUT
WWWW
WW
V+WWWWW
Model No.: LENNY-DRV-LS2
Working Temperature: -20~60°C
Input Voltage: DC12V~24V
Output: 6A/Channel
Total Output: Max 15A
RF: 2.4GHz
Control Distance: 30m
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
23
124
38 17
74.5
36
LENNY-DRV-LS2 LENNY-DRV-WL5 LENNY-DRV-WL2P
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
4
Technical specifications
ALTERNATE CURRENT DRIVER TRIAC controller
Model LENNY-TRIAC1
Input voltage AC 100-240V 50/60Hz
Output voltage AC 100-240V
Ouput current MAX 1.36A
Output power 150W@100VAC;
300W@240VAC
Regulation method Wireless RF, push button, APP
RF range 30m
Working temperature -10-40ºC
WIFI Requires gateway
LENNY-WIFOX1
49
25 49
WIFI GATEWAY
Model LENNY-WIFOX1
Working voltage DC5V/500mA (Micro USB)
Working temperature -20~60°C
Communication WiFi-IEEE 802.11b/g/n 2.4GHz
Working frequency 2.4GHz
Transmission power
6dBm
* Suggested AC/DC adaptors (not included): MWMU10GS
FU-ADPY10-5-USB
90,5 15
66
2.4GHz Gateway
Model No.: LENNY-WIFOX1
INPUT
DC5V / 500mASET
Input Voltage: DC5V/500mA (Micro USB)
Working Temperature: -20~60°C
Communication Mode: WiFi-IEEE 802.11b/g/n 2.4GHz
RF: 2.4GHz
2.4GHz RF Transmitting Power 6dBm
2.4GHz RF Control Distance: 30m
Link
SYS
Support amazon alexa and
google assistant control
Scan to Install APP
Made in PRC
by
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
5
by
SINGLE COLOR
Touch panel functions: LENNY-PAN-B0
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the
receiver or using the LENNY-WIFOX1 gateway.
ON /OFF
Brightness level regulation
Exit preload mode
and night mode
Programmed modes
Increase the speed
of the programmed modes
Decrease the speed
of programmed modes
Define LED type:
Single color
Tunable white
RGB
RGB+white
RGB+tunable white
Night mode: 1% brightness
WIFI RECEIVER WIFI GATEWAY
Brightness bar: white brightness regulation.
On Program mode activitation: Short press for slow down.
On Static mode activation: press for 2 seconds and system will
dim for 60 seconds up to lights reach turn off.
With programmed mode active: Short press and increase
speed.
With static mode activated: press for 2 seconds and it will dim
for 10 minutes up to lights reach turn off.
by
Timer Link / Unlink
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
6
by
TUNABLE WHITE
Touch panel functions: LENNY-PAN-B0
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the
receiver or using the LENNY-WIFOX1 gateway.
ON /OFF
Brightness level regulation
Exit preload mode
and night mode
Programmed modes
Increase the speed
of the programmed modes
Change color temperature
if our system is ready
to support such function
Decrease the speed
of programmed modes
Define LED type:
Single color
Tunable white
RGB
RGB+white
RGB+tunable white
Night mode: 1% brightness
WIFI RECEIVER WIFI GATEWAY
Brightness bar: white brightness regulation.
Dynamic white bar: Dynamic white mixing from the warmest
to the coolest tone.
On program mode active: Short press for dimming.
On static mode active: Press for 2 seconds to dim for
60seconds up to lights go out.
On program mode active: Short press to increase the
speed.
On static mode active: press for 2 seconds to dim for 10
minutes up to lights go out.
by
Timer Link / Unlink
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
7
RGB
Touch panel functions: LENNY-PAN-B0
by
Brightness level regulation
Green static
Blue static
Speed+
Speed–
Color ring
Color saturationr
White
Mode
Link / Unlink
Red static
OFF
Slide your finger over the coloured ring to change
colors.
Color saturation level
Color brightness level and white changing.
ON switch. Also it is used to link and unlink controllers.
OFF switch.
White direct switch.
Red direct switch.
Green direct switch.
Blue direct switch.
Dynamic modes.
Under dynamic mode running, you can
get slow speed with this switch. During static
mode, 2 sec long press to get once light.
Light will stop after 60 sec
Bajo el modo dinámico pulse este botón
para acelerar la velocidad. En el modo
estático, una pulsación larga de 2 sec.
produce luz una vez. La luz se desconectará
a los 10 min.
Working mode
• Select color: Touch color wheel on desired color (e.g.blue).
• Color saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
• Brightness bar: Adjust brightness level.
• White: With any color selected from color wheel, click on “W” to set full white with R+G+B mixing.
– Brightness slide bar: White brightness level setting.
– Tunable white: Once white activated, use “color “saturation bar” to set different white tones from RGB leds mixing.
• With a static color activated, saturation (slide “Color saturation” bar) and brightness can be adjusted. You can reach
Upwards 100% and downwards 0% levels.
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
8
RGB
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the
receiver or using the LENNY-WIFOX1 gateway.
Working mode
• Select color: Touch color wheel on desired color (e.g. blue).
• Saturation: Adjust color saturation (0% chosen color, 100% very saturated color).
• Brightness level: Adjust brightness level.
• White color: Bring out white color using R+G+B mixing combination (If maximum level is required, set saturation bar at
highest level).
• Tunable white: System allows to simulate dynamic white levels using RGB leds.
Color ring
White with RGB
ON / OFF
Saturation
Tunable white
Brightness level regulation
Timer
Modes
0%
0%
100%
100%
Increase the speedDecrease the speed
Define LED type:
Single color
Tunable white
RGB
RGB+white
RGB+tunable white
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
9
RGBW
Touch panel functions: LENNY-PAN-B0
by
Brightness regulation
Green static
Blue static
Speed+
Speed–
Color ring
Temperature color
from white channel
White
Modes
Link / Unlink
Red static
OFF
Slide your finger over the colored ring to change
colors.
Increases or decreases white channel brightness
only (from the fourth W channel). If there is a previous
selected RGB color, adds white to RGB color.
Color and white brightness control.
ON switch. Also it is used to link and unlink controllers.
OFF switch.
White direct switch.
Red direct switch.
Green direct switch.
Blue direct switch.
Dynamic modes.
Under dynamic mode running, you can
get slow speed with this switch. During static
mode, 2 sec long press to get once light.
Light will stop after 60 sec.
Under dynamic mode running, you can get
light running faster with this switch. During
static mode, 2 sec long press to get once
light. Light will stop after 10 min.
Working mode
• Select color: Touch color wheel on desired color (e.g. blue).
• Brightness level: Adjust brightness level.
• Only white activation : Click on “White” to reach pure white.
• Color+White activation: Set desired color on the color wheel then adjust white with saturation slide bar (0% on the left
side, then white channel OFF, 100% on the right side, then white fully ON).
–Note: Once brightness level has been selected, if we push “W” then it will be switched ON at selected level.
• Color + White and selected color cancelation: Push W.
• Color + White and white setting cancelation: White channel slide bar on the left (0%).(downwards).
• With a static color on, the saturation (Slide “Color saturation” bar) and brightness can be adjusted. You can reach
Upwards 100% and downwards 0% levels.
LENNY-PAN-B0 1ZONE control
Smart LED control system
by
10
Working mode
• Select color: Touch color wheel on desired color (e.g. blue).
• “Saturation” bar: Adjust color saturation (0% chosen color, 100% very saturated color).
• Brightness level: Adjust brightness level.
• White light: Only white channel activation set.
– The “Brightness slide bar” is used to set desired brightness level.
• Color + White activation: Choose color with “color slide wheel” and set white level with saturation bar (0% white
channel off, 100% white channel set at max level).
• Remove Color + white and Color levels: Press “White light”.
Color ring
White
ON / OFF
Saturation
Timer
Modes
0%
0%
100%
100%
Increase the speedDecrease the speed
Brightness
Define LED type:
Single color
Tunable white
RGB
RGB+white
RGB+tunable white
RGBW
Mobile control
For control via mobile phone, Alexa, Google Home or Google Assistant, a WIFI gateway is required, either built into the
receiver or using the LENNY-WIFOX1 gateway.
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Mi-Light Sistema di controllo
Mi-Light
Mi-Light FUT027 Istruzioni per l'installazione
Mi-Light
Mi-Light MIBOXER LDRF-RGB6-TC4 Manuale utente
Mi-Light
Mi-Light MIBOXER FUT043A Manuale utente
Mi-Light
Mi-Light fullwat LENNY-MD-092 Manuale utente
Mi-Light
Mi-Light fullwat TRIAC CONTROL Manuale utente
Mi-Light
Mi-Light LS3 Istruzioni per l'installazione
Mi-Light
Mi-Light MiBoxer S1-B Manuale utente
