MICRO-EPSILON scanCONTROL 2910 Manuale utente
Page 1
scanCONTROL 2910/2960BL
Assembly Instructions
scanCONTROL 2910/2960BL
1. Warnings
Connect the power supply and the display-/output device according to the safety
regulations for electrical equipment. The supply voltage must not exceed the specified
limits.
> Risk of injury, damage to or destruction of the sensor
Avoid shocks and impacts to the sensor. Avoid constant exposure of the sensor to dust
and splashes of water. Avoid exposure of sensor to aggressive materials (detergents,
cooling emulsions).
> Damage to or destruction of the sensor
Read the detailed operation instructions before operating the sensor.
These instructions are available Online at www.micro-epsilon.com.
2. Notes on CE Marking
The following apply to the scanCONTROL 2910/2960-xx/BL:
- EU Directive 2014/30/EU
- EU Directive 2011/65/EU
The sensor is designed for use in industrial environments.
The sensor satisfies the requirements if the guidelines in the operation instructions are
maintained in installation and operation.
3. Proper Environment
- Protection class: IP65
- Temperature range:
Operation: 0 ... +45 °C (+32 ... +113 °F), for free circulation of air
Storage: -20 ... +70 °C (-4 ... +158 °F)
- Humidity: 5 - 95 % (non-condensing)
Page 2
scanCONTROL 2910/2960BL
4. Laser Safety
The Sensoren scanCONTROL 2910/2960-xx/BL operate with a semiconductor laser
with a wavelength of 405 nm (visible/blue). Operation of the laser is indicated visually
by the LED on the sensor, see operating instructions, Chap. 3.3.
When operating the scanCONTROL 29xx sensors, the relevant regulations according to
IEC 60825, Part 1 of 05/2014 and the applicable accident prevention regulations must
be followed.
The laser warning labels for Germany have already been attached. For other non Ger-
man speaking countries, an IEC standard label is included in delivery and the versions
valid for the user‘s country must be attached before the device is put into operation for
the first time.
iIf both warning labels are covered over when the unit is installed, the user must
ensure that supplementary labels are applied.
Laser radiation. Close your eyes or immediately turn away if the
laser beam hits the eye. Irritation or injury of the eyes possible.
Laser Class 2M
The sensors fall within laser class 2M. The laser is operated on a pulsed mode, the
maximum optical power is ≤ 8 mW (scanCONTROL 29xx-10/BL ≤ 7 mW). Attach the
following warning labels to the cover (front and rear side) of the sensor housing:
Laser warning sign and laser label, LLT 29xx-25/BL, 29xx-50/BL, 29xx-100/BL
7 7 6
Laser warning sign and laser label, LLT 29xx-10/BL
Mark the laser area recognizable and everlasting.
Page 3
scanCONTROL 2910/2960BL
scanCONTROL
Fig. 1 Sensor with laser labels
5. Unpacking, Included in Delivery
- 1 scanCONTROL 2910/2960-xx/BL sensor with integrated controller
- 1 PCR3000-5 multifunction cable, length 5 m; for power supply, trigger and RS422;
screw connector and free cable ends
- Calibration protocol / assembly instructions
- 2 Protective caps
Page 4
scanCONTROL 2910/2960BL
6. Connections, LED Indication
1 2
1 Ethernet port
2 Multifunction port (Power supply, I/O)
Multifunction Port
Designation Sensor con-
nector pin
Cable color
PCR3000-x
Notes
+Ub 9 Red + 11 V - 30 V DC
(rated value 24 V); max. 5 W
GND 2 Blue 0 V
+Laser on/off 3 White Available with SI option
-Laser on/off 1 Brown
RS422 12 Red-blue RS422
input or output
/RS422 11 Gray-pink
In1 6 Yellow Switching input In1
GND-In1 4 Green Ground connection In1
In2 5 Pink Switching input In2
GND-In2 8 Gray Ground connection In2
In3 10 Purple Switching input In3
GND-In3 7 Black Ground connection In3
Shield Housing Black Not electrically connected to GND
2
3
4
5
6
7
8
9
1
10
11
12
GND: galvanically isolated from IN1, IN2, IN3, RS422,
laser on/off
laser on/off: input galvanically isolated from GND,
IN1, IN2, IN3, RS422
IN1, IN2, IN3, RS422: inputs galvanically isolated
from GND and laser on/off
12-pin. screw connector, view on solder side (cable)
RS422, Synchronization
The RS422 connection (Pin 11 and 12 of the multifunction port) can be used in either of
the following configurations:
- RS422 (half-duplex): Load user modes and sensor control, sensor control and
transmission of measurement results (Modbus RTU or ASCII format)
- Synchronization/triggering: Synchronization or triggering using switching signals
Page 5
scanCONTROL 2910/2960BL
Trigger, Encoder, Mode Switching
The switching inputs of the multifunction port can either be used for encoder input,
trigger input or for load previously stored user modes.
The signal levels are switchable for all switching inputs between LLL (low voltage, TTL
logic) and HLL (high voltage, HTL logic):
- LLL level: Low 0 V … 0,8 V, high 2.4 V … 5 V, internal pull-up 10 kΩ connected to
5 V
- HLL level: Low 0 V … 3 V, high 11 V … 24 V (permitted to 30 V), internal pull-up
10 kΩ connected to 24 V
- Pulse duration: ≥ 5 µs
External Laser Switch-off, Optional
The external laser switch-off is implemented as a hardware solution and has a top prior-
ity. The laser can be switched off, in addition, also by software.
This function is offered by sensors with the /BL-SI option.
Use a serial key switch in the control circuit to switch off the laser.
With standard sensors, connecting the supply voltage activates the laser light source in
the sensor.
Wiring details are available in the operating instructions, Chap. 5.2.6.
Page 6
scanCONTROL 2910/2960BL
Ethernet Connection, Standard Connection to PC
RJ45 connector 8-pin. screw connector (sensor side)
Pin no. Color of stranded hook-
up wire SCR3000A-x
Pin no. 10BaseT,
100BaseTX
1000BaseT
1 White (orange) 5 Tx+ D1+
2 Orange 6 Tx- D1-
3 White (green) 8 Rx+ D2+
4 Blue 1 D3+
5 White (blue) 2 D3-
6 Green 7 Rx- D2-
7 White (brown) 3 D4+
8 Brown 4 D4-
1View on pin side
of male cable
connector
2
3
4
5
6
7
8
1
View on solder side (ca-
ble) of screw connector
(A-coded)
- The sensor supports an automatic, sensor-adapted IP address in the link-local-net
(169.254.x.x). No collision check is performed. This is also the standard setting.
- The sensor supports DHCP. This setting is activated by default and has priority over
the retrieval in the link-local net.
- The sensor scanCONTROL 2610/2960BL supports Power over Ethernet.
If the sensor is connected to a POE-capable network adapter/
switch and you also use the power supply of the multifunction
port, these two power supplies must be galvanically isolated.
> Damage to the sensor and /or Ethernet card!
- A fixed IP address can be assigned.
Use the sensorTOOL program to make specify the sensor settings described
above.
The program is available Online at https://www.micro-epsilon.de/service/download/
software.
Page 7
scanCONTROL 2910/2960BL
LED Indication
LED Laser on LED state
Green: Laser on Green: Measurement active
Green, flashes long Data transmission is
active
Green, flashes short Controller accesses
Red, flashes Error code
The state LED indicates different error states by flashing. If
no flashing occurs for several seconds, no error has occurred.
For a detailed description of the error codes, please refer to the
operating instructions, Chap. 12.
7. System Requirements
scanCONTROL Configuration Tools
The following minimum system requirements are necessary:
- Windows 7, Windows 8 or 8.1, Windows 10 (each 32 bit and 64 bit)
- 1-GHz or faster (32 bit and 64 bit) processor / 1 GB RAM
- Screen resolution: 1024x768
scanCONTROL 3D-View
The following minimum system requirements are necessary:
- Windows 8 or 8.1 (64 bit), Windows 10 (64 bit)
- 1-GHz or faster (64 bit) processor
- 1 GB RAM
- Screen resolution: 1024x768
- Graphic card / GPU with OpenGL 3.1 or higher
8. Transmitting Measurement Results
scanCONTROL 2910/2960BL offers the following options for transmitting measurement
results:
- Ethernet interface
Modbus TCP protocol
UDP protocol
Analog output of measurement values (via optional Output Unit)
Digital output of switching (via optional Output Unit)
Fieldbus connection PROFINET, EtherNet/IP, EtherCAT (via optional Gateway)
- RS422 interface
Modbus RTU protocol
Measurement value transmission in ASCII format
Page 8
scanCONTROL 2910/2960BL
9. Quickstart: Initial Operation, Software
Mount the sensor according to the installation instructions.
Install the software.
You will find the software Online on
the product website of the sensor
or in the download area:
https://www.micro-epsilon.
de/2D_3D/laser-scanner/Software/
downloads/.
Follow the dialog instructions through the
installation process:
A. Read the installation help
B. Install the software
C. Additional information in the Online docu-
mentation
Connect the sensor to the PC using the optionally available SCR3000A-x Ethernet-
cable.
Connect the shield of the power supply cable to the PE grounding conductor of
the main power supply. Close connection plugs you do not require with the includ-
ed protective caps. Turn on the power supply (24 VDC).
Please wait until the scanCONTROL measuring system is recognized by the PC.
This may take a few seconds.
Now you can operate the scanCONTROL measuring system with the scanCONTROL
software packages.
iOperating the sensors via Ethernet may require the IP settings of the PC/sensor
or the firewall settings to be adjusted, see Chap. 5.2.5 of the operating instruc-
tions.
The connectors for Ethernet and the multifunction port include a screw connector.
Loosen the screws connection before you remove the connector from the socket.
iOnly connect the sensor to the peripheral equipment, if it is disconnected from
the power supply, i.e. only when the supply voltage is switched off. The sensor
needs a warm-up time of typically 20 minutes for high precision measurements.
Page 9
scanCONTROL 2910/2960BL
10. First Profile
Now start the scanCONTROL Configuration Tools software. Click on Display
Profiles in the main window.
If the software shows the error message No scanCONTROL found in the status line,
please check the Ethernet connection between scanCONTROL and PC.
On the left side you can adjust the settings for your measurement task. The right side
shows the profile data and further information about the measurement.
11. How to Access Profile Data
Profile data of scanCONTROL can be accessed via:
- GigEVision and GenICam for digital cameras via Ethernet
- SDK for fast application integration (C, C++, C# and others)
Please refer to the respective SDK documentation for further information on accessing
the profile data.
Page 10
scanCONTROL 2910/2960BL
13. scanCONTROL 2910/2960BL with scanCONTROL Output Unit for Connecting to a PLC
++
-
13 14
C
D
B
A
750-626
+
+ Ñ
-
-
Power contacts
Supply via power
contacts
24V
Status of
supply voltage
- Power contacts
- System
Data contacts
System supply
(OUT)
24 V
0 V
0 V
System supply
(In)
24 V
0 V
C
D
B
A
750-600
OU filter module
Bus terminationAnalog output terminal
253-057
LINK
ACT
MS
I/O
ETHERNET
NS
87654321
NO
LINK
ACT 1
2
X
1
X
2
8
1
ON
24V
X3
0V
0: WBM
255: DHCP
OU fieldbus coupler
A1
A2
13
14
750-536
A3
A4
A5
A6
A7
A8
DO 2
Power contacts
Data contacts
DO 2
Status
D0 4
D0 6
DO8
DO 8
Digital output terminal
DO 1
Status
DO 7
DO 7
DO 1
DO 5
DO 3
A1 A2
13 14
C
D
B
A
MM
A3 A4
M M
750-555
AO 2
AO 1
AO 4
AO 3
V0V0
V0V0
Power contacts
Data contacts
Function
Error
L1
L2
L3
N
PE
OU Filter module
OU Fieldbus coupler
++
-
13 14
C
D
B
A
750-626
+
+ Ñ
-
-
253-057
LINK
ACT
MS
I/O
ETHERNET
NS
87654321
NO
LINK
ACT 1
2
X
1
X
2
8
1
ON
24V
X3
0V
0: WBM
255: DHCP
System supply
Field supply
230 V
24 V
230 V
24 V
Altri manuali per scanCONTROL 2910
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali MICRO-EPSILON Strumento di misura
MICRO-EPSILON
MICRO-EPSILON surfaceCONTROL 3D SC3200-80 Manuale utente
MICRO-EPSILON
MICRO-EPSILON scanCONTROL 25 BL Series Manuale utente
MICRO-EPSILON
MICRO-EPSILON colorCONTROL MFA-1 Manuale utente
MICRO-EPSILON
MICRO-EPSILON optoControl 1200 Manuale utente
MICRO-EPSILON
MICRO-EPSILON gapCONTROL 2711 Manuale utente
MICRO-EPSILON
MICRO-EPSILON surfaceCONTROL 3D 35 Series Manuale utente
MICRO-EPSILON
MICRO-EPSILON scanCONTROL 3000/BL Manuale utente
MICRO-EPSILON
MICRO-EPSILON surfaceCONTROL 3D SC3200 Manuale utente
MICRO-EPSILON
MICRO-EPSILON NLS3181 Manuale utente
MICRO-EPSILON
MICRO-EPSILON ILD1402-5 Manuale utente
MICRO-EPSILON
MICRO-EPSILON thermoMETER CS Manuale utente
MICRO-EPSILON
MICRO-EPSILON eddyNCDT SGS 4701 Manuale utente
MICRO-EPSILON
MICRO-EPSILON thicknessCONTROL MTS 8202.LLT Manuale utente
MICRO-EPSILON
MICRO-EPSILON optoCONTROL 2520 Manuale utente
MICRO-EPSILON
MICRO-EPSILON confocalDT IFD2410 Series Manuale utente
MICRO-EPSILON
MICRO-EPSILON thicknessCONTROL MTS 8202.LLT Manuale utente
MICRO-EPSILON
MICRO-EPSILON combiSENSOR 64x0 Manuale utente
MICRO-EPSILON
MICRO-EPSILON CS005 Manuale utente
MICRO-EPSILON
MICRO-EPSILON eddyNCDT 3060 Guida all'installazione
MICRO-EPSILON
MICRO-EPSILON FSC1/7 Manuale utente
