Microsemi VSC8502 Manuale utente
VSC8502
User Guide
VSC8502 Reference Board
May 2014
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0
Contents
1 Revision History ............................................................................................................................. 1
1.1 Revision 1.0 ........................................................................................................................................ 1
2 Introduction ................................................................................................................................... 2
3 General Description ....................................................................................................................... 3
3.1 Copper Port RJ45 Connections ........................................................................................................... 3
3.2 RGMII MAC Connectors ...................................................................................................................... 3
3.3 Static Controls (SW1) .......................................................................................................................... 3
3.4 Clocking .............................................................................................................................................. 3
3.5 Software Interface Microcontroller Card ........................................................................................... 3
3.6 Software Interface Microcontroller Card ........................................................................................... 4
4 Quick Start ..................................................................................................................................... 5
4.1 Connecting the Power Supply ............................................................................................................ 5
4.2 PC Software Installation ..................................................................................................................... 5
4.3 Connecting to the Board to the PC ..................................................................................................... 5
4.3.1 Board Initialization .................................................................................................................................. 6
4.3.2 Copper Media Operation (Auto-negotiation Enabled) ............................................................................ 7
5 Useful Test Features ...................................................................................................................... 8
5.1 Ethernet Packet Generator ................................................................................................................. 8
5.2 Copper PHY Error Counters ................................................................................................................ 8
5.3 Near-End Loopback ............................................................................................................................ 8
5.4 Far-End Loopback ............................................................................................................................... 8
5.5 Transmitter Test Mode ....................................................................................................................... 8
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 1
1 Revision History
The revision history describes the changes that were implemented in this document. The changes are
listed by revision, starting with the most current publication.
1.1 Revision 1.0
Revision 1.0 of this datasheet was published in May 2014. This was the first publication of the
document.
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 2
2 Introduction
The VSC8502 device is a low-power, cost-optimized, dual-port Gigabit Ethernet PHY. It features
integrated, line-side termination to conserve board space, lower EMI, and improved system
performance. To further reduce system complexity, component count, and system cost, the VSC8502
device can operate from a single 3.3 V supply using integrated voltage regulators. Additionally,
integrated RGMII timing compensation eliminates the need for on-board delay lines. The device also
optimizes power consumption in all link operating speeds and features Wake-on-LAN (WOL) power
management using magic packets. This document describes the architecture and usage of the
VSC8502RD and VSC8502RD-VR Reference Design Boards. The Quick Start section describes how to
install and run the graphical user interface (GUI) to fully control the evaluation board.
Figure 1 • VSC8502RD Reference Board E
The following illustration shows the 501 VSC8502 Reference Board.
Figure 2 • VSC8514 Evaluation Board (Bottom View)
Additional VSC8502 collateral for both the VSC8502 device and VSC8502 reference design, including
schematics, layout, GUI, and application notes can be found on the VSC8502 product web page at: www.
.vitesse.com/products/product/VSC8502
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 3
3 General Description
The evaluation board, shown in Figure 1, provides the user a way to evaluate the VSC8502 device in
multiple configurations. Two RJ-45 connectors are provided for copper media interfaces. The MAC
interface (RGMII) is exposed via 0.1 inch steakheaders, J31 - J53. For standalone access to all of the
features of the device, an external microcontroller is used to configure the VSC8502 via the MDIO bus.
The GUI enables the user to read and write device registers.
3.1 Copper Port RJ45 Connections
PHY ports 0 and 1 use generic RJ45 connectors with discrete Halo TG1G-S032NYRL magnetics.
3.2 RGMII MAC Connectors
The parallel MAC interface is available through 0.1 inch headers. The layout is such that by installing
jumpers the RX and TX signals can be looped on board. When mating to a MAC board, a specialized
cable will need to be constructed.
The following is the RGMII connectors positioned in the board:
Table 1 • RGMII Connector Positions
Channel 1 Channel 0
GND GND GND GND GND GND GND GND GND GND GND GND
RXD2 RXDV_CTL RXD0 RXD3 RXD1 RXCLK RXD3 RXDV_CTL RXD2 RXD0 RXD1 RXCLK
TXD2 TXDV_CTL TXD0 TXD3 TXD1 TXCLK TXD3 TXDV_CTL TXD2 TXD0 TXD1 TXCLK
GND GND GND GND GND GND GND GND GND GND GND GND
3.3 Static Controls (SW1)
Three static control signals are set by the DIP switch SW1.
Signal Name Description Position for Normal Operation
REFCLK_SEL Select the input frequency to the device.
0: 125 MHz
1: 25 MHz
1
NRESET Hold the device in rest.
0: Reset state
1: Normal device operation
1
COMA_MODE Hold the device in coma state.
0: Disabled
1: Enabled
0
3.4 Clocking
VSC8502RD board is equipped with a 2.5V CMOS, 25.00 MHz standard clock oscillator (U5), while the
VSC8502RD-VR board uses a 3.3 V CMOS version.
3.5 Software Interface Microcontroller Card
A Silabs F340 microcontroller is included to facilitate a software interface to the registers on the
VSC8502 through a USB port.
Note: Alternatively, a Rabbit card is available for an IP-based manager of the PHY register space,
installed in the keep-out area (U6) of the board’s top-side. Or, MDC and MDIO can be accessed on stake
header J10 if desired for another microcontroller to host the PHY register space.
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 4
3.6 Software Interface Microcontroller Card
The VSC8502RD or VSC8502RD-VR is powered by plugging in a USB cable to the board and to a PC. For
the VSC8502RD board, there are three on-board regulators that will convert the 5 V supplied by the PC
to 1.0 V and 2.5 V for the VSC8502 and 3.3 V for other devices. For the VSC8502RD-VR board, there is
only one on-board regulator that will convert the 5 V supplied by the PC to 3.3 V for the VSC8502’s
internal voltage regulators, VSC8502’s 3.3 V digital supplies, as well as other devices. A board will draw
less than 350 mA from the USB port.
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 5
1.
2.
3.
4.
4 Quick Start
This section shows the quick start for the VSC8502 Reference Board.
4.1 Connecting the Power Supply
The reference design board is powered by the USB cable. The on-board switcher(s) converts the +5V
USB power to the required power supplies for devices on the board. Please see section 2.6 for
reference.
Note: For proper device operation, prior to powering the board, ensure the NRESET input to the
VSC8502 through SW1 is in the low state (right position). After connecting the USB cable which supplies
power, toggle the NRESET input to the high state (left position) then back to the high state (left
position).
4.2 PC Software Installation
Download the ZIP file from Microsemi's website onto a PC that has a USB port
Install the GUI by launching the setup.exe file
USB communication is assisted by the Silabs USBXpress® drive. If not present on the PC, the user will
need to download the USBXpress
Development Kit from the Silicon Labs website (URL: http://www.silabs.com/products/mcu/Pages
)/USBXpress.aspx
Double click the desktop icon to launch the GUI
4.3 Connecting to the Board to the PC
After following the power sequence discussed in 3.1, launch the GUI either by clicking on the Desktop
shortcut or clicking on > > > . The initial Start Programs Vitesse Semiconductor Corp VSC8502_GUI
window will detect the attached USB devices automatically. Figure 3 shows a typical EVB Connection
window.
Figure 3 • GUI Connection Window
The EVB serial number should appear. If not, click on “Scan For USB Devices.” Select that EVB serial
number then click “Launch GUI”. The MII Register List GUI window will appear as shown in Figure 4.
When the communication is successfully established, it should say “CONNECTED” at the bottom left
corner of this GUI Window.
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 6
Figure 4 • MII Registers GUI Window
Verify the device is up and running by reading MII Register 0. It should read back 0x1040. Reading back
all 0’s or all 1’s indicates a problem. For a multi-port device, the corresponding PHY port number is
accessed via the “Port:” pick list shown above the Register Description in Figure 4.
As Figure 4 indicates, the extended MII register pages can be accessed to read or write by clicking on
one of the ExtMII/Ext2MII/ExtGMII tabs.
4.3.1 Board Initialization
Once the evaluation board connectivity has been established and confirmed, the PHY should be
initialized. Initialization can be accomplished by running an init-script sequence, such as performed by
the pre- and post-reset functions of the PHY API standalone app.
While the init-script sequence may not be required for specific operational modes, an init-script
sequence is highly recommended to ensure correct performance over the greatest set of user scenarios
for the PHY. After initialization is performed, refer to the PHY Datasheet section on Configuring the PHY
and PHY Interfaces for the desired application.
An initialization file, , is included in the GUI package. This initialization file will optimize vsc8502_init.txt
the copper media interface settings based on the latest factory test result. To execute initialization
script, click “Device” on the top menu and choose “Load Init Script” option, which will automatically load
and execute vsc8502_init.txt file in the directory. Once the initialization is completed, it should say
“LOADED 17 REGISTERS” at the bottom left corner of the GUI Window.
In addition, three other configuration scripts are included:
vsc8502_RGMII_2nsRXCLKdelay.txt: configure the MAC interface to RGMII mode with 2.0 ns RX_CLK
delay compensation. Note that the board is designed and laid out such that the RGMII DATA,
CONTROL and CLOCK for each direction are matched in length approximately within +/-200 ps.
vsc8502_RGMII_2nsGTXCLKdelay.txt: configure the MAC interface to RGMII mode with 2.0ns
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 7
1.
2.
3.
4.
5.
6.
7.
vsc8502_RGMII_2nsGTXCLKdelay.txt: configure the MAC interface to RGMII mode with 2.0ns
GTX_CLK delay compensation.
vsc8502_10BTe_Config.txt: optimize the copper media interface settings for 10BASE-Te.
To load and execute configuration scripts, click “Device” on the top menu and choose “Load Config
Script” option then select the desired script file. Once the script is executed, it should say “LOADED n
REGISTERS” at the bottom left corner of the GUI Window, where n is the loaded registers count.
4.3.2 Copper Media Operation (Auto-negotiation Enabled)
The easiest configuration for passing traffic is with Autoneg enabled (MII 0.12 = 1). Use MII Register 0, 4
and 9 to change speed and restart autoneg (MII 0 bit 9) to advertise new settings. As per the datasheet
descriptions, the commonly-used speed advertisement definitions are as follows:
Table 2 • Auto-Negotiation Advertisements
MII reg 4
bits 8:7
MII reg 4
bits 6:5
MII reg 9
bits 12:11
MII reg 9
bits 9:8
1000BT Master mode N/A N/A 11 11
1000BT Slave mode N/A N/A 10 11
100 BASE-TX Full Duplex 11 N/A N/A 00
10 BASE-T Full Duplex 00 11 N/A 00
The following steps are used to configure a link:
Set up the Copper traffic source (i.e., IXIA or Smartbits)
Run the vsc8502_init.txt script
Connect Ethernet cable(s) to a single or multiple RJ-45 ports
Connect 0.1 inch shunt jumpers between row-2 and row-3 of RGMII
connectors as external loopback within a single port
Configure MAC interface for RGMII mode, enable RX_CLK output and set
RX_CLK or GTX_CLK delay, as described in Configuration section of the
datasheet. Alternatively, this can also be done by running either one of the
two RGMII configuration scripts.
Configure auto-negotiation as per above and re-start ANEG (MII bit 0.12)
The linkup bit is in MII Reg 1, bit 2 (MII 1.2), read it twice to update
Traffic should now be flowing.
VSC8502 Reference Board
VPPD-03822 VSC8502 User Guide Revision 1.0 8
5 Useful Test Features
5.1 Ethernet Packet Generator
ExtMII 29E is the Ethernet Packet Generator register. The EPG sends traffic in multiple of 10,000 frames
regardless of when you stop transmit activity. Refer to the datasheet for configuration options.
A Good CRC packet counter is in ExtMII 18.13:0. The Good CRC packet counter is a modulo 10,000
counter so values will always be between 0-9,999. A read of the register reads back the good CRC
packets and then clears the register so the subsequent reads will be 0 if no traffic has been received. If
traffic has been received since the last read, bit 15 will be set.
5.2 Copper PHY Error Counters
Idle errors = MII 10.7:0
RX errors = MII 19.7:0
False carrier = MII 20.7:0
Disconnects = MII 21.7:0
CRC errors = ExtMII 23.7:0
5.3 Near-End Loopback
When the near-end loopback test feature is enabled, the transmitted data is looped back in the PCS
block on the receive data signals. To enable the loopback, set register bit 0.14 to 1. Near-end loopback
mode involves traffic flow over the GMII/RGMII interface, so a breakout of the MAC interface on
SAMTEC connector J1 must be connected to another system for this mode to pass traffic.
5.4 Far-End Loopback
When the far-end loopback test feature is enabled, incoming data from a link partner on the Copper
interface to be transmitted back to the link partner on the Copper interface. To enable the loopback, set
register bit 23.3 to 1.
5.5 Transmitter Test Mode
1000BASE-T PMA test control can be configured through reg.9.15:13. Please refer to PMA Test
application note for additional information in regard to performing the PMA conformance test.
Altri manuali per VSC8502
1
Indice
Altri manuali Microsemi Scheda madre
Microsemi
Microsemi VSC8211 Manuale utente
Microsemi
Microsemi SmartFusion2 MSS Manuale utente
Microsemi
Microsemi VSC8514 Manuale utente
Microsemi
Microsemi LX7302 Manuale utente
Microsemi
Microsemi VSC8489 Manuale utente
Microsemi
Microsemi LX7175 Manuale utente
Microsemi
Microsemi PD69208 Manuale utente
Microsemi
Microsemi VSC8502 Manuale utente
Microsemi
Microsemi FlashPro5 Manuale tecnico
Microsemi
Microsemi LX8204 12 V E-Fuse Manuale utente
Microsemi
Microsemi LX1970 Manuale utente
Microsemi
Microsemi LX2206 Manuale utente
Microsemi
Microsemi FlashPro Lite Manuale tecnico
Microsemi
Microsemi LX7186A Manuale utente
Microsemi
Microsemi IGLOO2 FPGA DSP FIR Filter Manuale utente
Microsemi
Microsemi PD70211EVB50FW-5 Manuale utente
Microsemi
Microsemi FlashPro4 Manuale utente
Microsemi
Microsemi LX23224IDB Manuale utente
Microsemi
Microsemi VSC8257 Manuale utente
Microsemi
Microsemi Actel IGLOO Icicle Manuale utente
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
