Mienta SI18303A Manuale utente

Instruction Manual 1

Steam Iron-Clear SI18303A

Instruction Manual

2Instruction Manual

Before using your appliance, you must familiarize yourself with the different components of

your appliance. Every letter corresponds to one of the components of your appliance.

Components

Spray Nozzle

Water Fill Cover

Steam Control/Self Clean Knob

Temperature Control Knob

Steam Burst Button

Spray Button

Indicator Light

Ceramic Soleplate

Thank you for choosing products

Safety instructions

Please carefully read the instructions before using your appliance for the ﬁrst time.

Any use that does not conform to the following instructions does not hold

accountable and cancels your product’s warranty.

•

Use the iron only for its intended use.

To protect against the risk of electric

shock, do not immerse the iron in water

or other liquids.

The iron should always be turned to MIN

before plugging or unplugging from

outlet. Never yank

cord from the outlet to disconnect;

instead, grasp plug and pull to

disconnect.

Do not allow cord to touch hot surfaces.

Let iron cool completely before putting it

away. Cover the iron when stored and

loop the cord around iron.

Always disconnect iron from electrical

outlet when ﬁlling with water or emptying

and when not in use.

Do not operate iron with a damaged

cord or if the iron has been dropped or

damaged. To avoid the

risk of electric shock, do not

disassemble the iron, visit your nearest

qualiﬁed service center for

examination and repair. Incorrect

reassembly can cause a risk of electric

shock when the iron is used.

Close supervision is necessary for any

appliance being used by or near

•

children. Do not leave iron unattended

while connected or on an ironing board.

Burns can occur from touching hot

metal parts, hot water, or steam. Use

caution when you turn a

steam iron upside down – there may be

hot water in the water tank.

All repair work should be carried out by

an approved service center.

Push steam button a few times and

lightly shake iron after use to ensure all

water is drained. The remaining moisture

will evaporate if you plug in the cord and

heat iron for a few moments.

To avoid a circuit overload, do not

operate an iron on the same circuit with

another high wattage appliance.

If an extension cord is absolutely

necessary, a cord with an ampere rating

equal to or greater than the maximum

rating of the iron shall be used. A cord

rate for less amperage can result in a

risk of ﬁre or electric shock due to

overheating.

The iron must be used and rested on a

stable surface.

Instruction Manual

SAVE THESE INSTRUCTIONS

Before the ﬁrst use

Operating Instructions

•

To do this, ﬁll water (using the supplied measuring cup) up to “MAX” line into the iron. Clean

steam vents by using “Self Clean” system. (See using the Self Clean Button)

When ﬁnished, wipe the soleplate with an old cloth. Cotton swabs may be used to clean and

dry the steam vents. Your iron now should be ready for use.

•

FILLING WITH WATER

1. Unplug the iron.

2. Flip the water ﬁll cover open.

3. Lift the iron till the water ﬁll cover is about vertical.

4. Pour slowly, to avoid airlocks.

5. Don’t ﬁll past max, or water will escape in use.

6. Close the cover, and wipe up any spillage.

Plug in the iron. The indicator light illuminates. Once the iron reaches the selected tempera-

ture, the light goes off , you may then start using your iron.

The indicator light will illuminate and go off regularly during ironing as an indication that the

temp control/thermostat is working properly.

IRONING TIPS

1. Sort the articles to be ironed according to the fabric. Ironing instructions are usually

stitched onto an inside seam of the garment and these should be followed at all the times.

Start your ironing with the fabrics requiring the lowest heat setting.

2. If you are unsure of the ﬁber content of a garment, test a small area (a seam or inside

hem) before ironing.

3. When in doubt, start with low heat. If wrinkles remain, gradually increase heat to ﬁnd the

best setting for good results without damaging the fabric.

4Instruction Manual

Before using for the ﬁrst time, check if the voltage rating on the base plate corresponds to

the electric voltage in your home.

Remove Storage Cover, sticker or any protective wrappings from the soleplate.

It’s necessary to completely remove all residues of the polishing compound used on the

soleplate of your iron which may have become trapped in the steam vents.

Some parts of the iron have been slightly greased and as a result the iron may smoke

slightly when switched on for the ﬁrst time. After a short while, however, this will cease.

Normal tap water can usually be used for ironing. But if you live in a hard water area, to

insure optimum performance of your iron, we recommend to use distilled water.

USING AS A STEAM IRON

1. Fill the water tank as described above.

2. Stand the appliance on its bottom cover.

3. Plug the appliance in and switch on.

4. Set the temperature control knob to the steam position and the indicator light will

illuminate.

5. In this setting, the iron can be used as a steam iron when the indicator light goes out. The

light will illuminate and go out regularly during ironing as a indication that the temperature

control is working properly.

6. Turn the Steam Control knob to the Steam position (as below picture) will create steam.

Turn the Steam Control knob to the position 0, the steam will cease.

7. When ﬁnished ironing, please turn the temperature

control to “min” position and turn the steam control

knob to “0” position, and unplug.

USING AS A DRY IRON

1. Stand the iron on the bottom cover, then plug the iron in.

2. Turn the Steam Control knob to “0”.

3. Adjust the temperature control knob to the proper temperature.

When the indicator light goes out, it indicates the iron has reached the required temperature.

USING THE STEAM BURST BUTTON

Be sure there is water in the tank and the iron is on a high temperature setting.

1. Using the iron Horizontally

Lift the iron and press the steam burst button. You may need to press the button few times

after ﬁlling with water to activate the pump. The burst steam facility can be used only while

ironing with high ironing temperature (from to / Max).

2. Using the iron Vertically

The burst function can be also used when the iron is held in vertical position to remove

creases from hanging clothes, curtains, etc…

USING THE SPRAY BUTTON

As long as there is enough water in the water tank, you may use spray button at any

temperature setting either on Steam or Dry ironing. Press the button several times to activate

the pump while you are ironing.

Instruction Manual

•• •••

Cleaning and Maintenance

1. Avoid ironing over zippers, rivets on jeans, etc., as they will scratch the soleplate. Iron

around them instead. Keep the iron soleplate smooth.

2. Water and its minerals vary widely by geographic location. If you live in a hard water area,

to insure optimum performance of your iron, we strongly recommend the use of distilled

water which is readily available in retail stores.

3. Do not disassemble or repair your iron yourself.

USING THE SELF-CLEAN FUNCTION

1. It is important to apply “self-clean” function at the ﬁrst time of using the iron then at least

once per month to remove scale etc.

2. Fill the water up to “MAX” line in water tank.

3. Insert the plug into the wall socket.

4. Set the Temperature Control knob to Max.

5. Allow the iron to heat up until the heating light goes out.

6. Remove the plug from the wall socket.

7. Keep the iron horizontally over the sink.

8. Turn the Steam control knob to self-clean position

Hold the gear on self clean position.

The boiling water and steam will come out from the vents in the soleplate. Impurities and

scale (if any) are washed away.

9. Move the iron forwards and backwards while this happens.

10. Release the steam control knob when all water is used up.

11. Stand the iron upright then insert the plug into the wall socket and heat up the iron.

12. Carefully dry soleplate by ironing over a towel or old cloth to ensure there is no remainder

of the water inside the steam chamber.

13. Do not use chemically descaled water.

14. Let iron cool completely before storing.

ANTI-DRIP FEATURE

The Anti-Drip function ensures that the iron will not drip water at low temperature after

steaming. Steaming will recommence as soon as the appropriate temperature has been

reached.

6Instruction Manual

TO EMPTY AND STORE

Be sure the iron is unplugged ﬁrst. Pour out any remaining water by shaking the iron.

Make it a habit to empty the iron after each use.

After emptying the water tank, keep the hot iron in an upright position, so that any moisture

remaining will evaporate quickly. Let iron cool completely before storing.

Instruction Manual

Trouble Shooting

The iron is connected to a wall plug.

The heat setting is set on MAX.

The cable is not damaged.

If your iron is not working, please check the following:

•

If your appliance is still not working, contact a approved service centre.

Technical Speciﬁcation

Model: SI18303A

Power Supply: 230V~50Hz

Power: 2200 W

VER.A

8Instruction Manual

Instruction Manual 1

Fer à repasser vapeur- Clear SI18303A

MODE D’EMPLOI

Avant d'utiliser votre appareil, vous devez vous familiariser avec les différentes parties de

votre appareil. Les lettres correspondent aux différents composants de votre appareil,

représenté ci-dessous.

Composants et Caractéristiques:

Buse de pulvérisation.

Buse de remplissage d'eau.

Variateur de vapeur/ Bouton de nettoyage des dépôts calcaires.

Variateur de température / thermostat.

Le bouton de jet de vapeur.

Le bouton de pulvérisation d’eau.

Témoin lumineux.

Semelle en céramique

*Merci d’avoir choisi la qualité

10 Mode D’emploi

Indice

Lingue:

Manuali Ferro popolari di altre marche

Clatronic

Clatronic DB 3703 Manuale utente

TEFAL

TEFAL FV4093Z0 Manuale utente

Gorenje

Gorenje SIH 2200 BS Manuale utente

Philips

Philips GC6012 Manuale utente

Bosch

Bosch 2 Series Manuale utente

Riffel

Riffel Catena KB-819 Manuale utente

Texi

Texi Hestia Manuale utente

Maxwell

Maxwell MW-3010 Manuale utente

TREVIDEA

TREVIDEA Girmi ST60 Manuale utente

Philips

Philips HI5914/30 Manuale utente

Primula

Primula Vapormat Manuale utente

Magio

Magio MG-541 Manuale utente

Scarlett

Scarlett SC-1334S Manuale utente

Bosch

Bosch Sensixx B22L Manuale utente

Philips

Philips GC651 Manuale utente

Vitek

Vitek VT-1247 VT Manuale utente

Cleanmaxx

Cleanmaxx 3397 Manuale utente

Philips

Philips GC800 Manuale utente