Minarik MMBOSS Series Manuale utente
Model:
MMBOSS05-24DC-1Q
MMBOSS
Series
User’s Manual
250-0288.qxd 6/9/00 1:05 PM Page a
Copyright © 2000 by Minarik Corporation
All rights reserved. No part of this manual may be reproduced or
transmitted in any form without written permission from Minarik
Corporation. The information and technical data in this manual
are subject to change without notice. Minarik Corporation and its
Divisions make no warranty of any kind with respect to this
material, including, but not limited to, the implied warranties of
its merchantability and fitness for a given purpose. Minarik
Corporation and its Divisions assume no responsibility for any
errors that may appear in this manual and make no commitment
to update or to keep current the information in this manual.
Printed in the United States of America
250-0288.qxd 6/9/00 1:05 PM Page b
Safety Warnings
•This symbol denotes an important safety tip or warning.
Please read these instructions carefully before performing
any of the procedures contained in this manual.
•DO NOT INSTALL, REMOVE, OR REWIRE THIS
EQUIPMENT WITH POWER APPLIED. Have a qualified
electrical technician install, adjust and service this equipment.
Follow the National Electrical Code and all other applicable
electrical and safety codes, including the provisions of the
Occupational Safety and Health Act (OSHA), when installing
equipment.
•Reduce the chance of an electrical fire, shock, or explosion by
proper grounding, over-current protection, thermal protection,
and enclosure. Follow sound maintenance procedures.
It is possible for a drive to run at full speed as a result of a
component failure. Minarik strongly recommends the
installation of a master switch in the main power input to stop
the drive in an emergency.
This drive is isolated from earth ground. Circuit potentials
are at 115 VAC or 230 VAC above earth ground. Avoid direct
contact with the printed circuit board or with circuit elements
to prevent the risk of serious injury or fatality. Use a non-
metallic screwdriver for adjusting the calibration trimpots.
Use approved personal protective equipment and insulated
tools if working on this drive with power applied.
250-0288.qxd 6/9/00 1:05 PM Page i
Contents
Specifications 1
Dimensions 3
Installation 5
Mounting ...........................................5
Wiring ..............................................6
Shielding guidelines .................................7
Heat sinking .........................................8
Fusing .............................................8
Speed adjust potentiometer mounting ......................9
Quick-connect terminal block ...........................10
Connections ........................................11
Motor, power and fuse connections .....................11
Optional switch connections ..........................14
Voltage follower signal connections ......................16
Motor hall sensor connections ...........................17
Jumper Settings .....................................19
Input Voltage Range Select (SW501) ...................19
Hall Sensor Spacing (SW502) ........................19
Operation 21
Before applying power ................................21
Startup ............................................22
Reversing ..........................................23
Starting and Stopping Methods ..........................24
Automatic restart upon power restoration ................25
ENABLE/DISABLE switch ...........................25
RUN/BRAKE switch ................................25
Coast to a stop ....................................25
ii
250-0288.qxd 6/9/00 1:05 PM Page ii
Decelerate to minimum speed ........................25
Calibration 27
MINSPD .........................................28
MAXSPD ........................................28
CURRENT LIMIT ...................................29
GAIN .............................................30
Application Notes 31
Multiple fixed speeds .................................31
Adjustable speeds using potentiometers in series ............32
Independent adjustable speeds .........................33
DIRECTION switch ..................................34
Troubleshooting 35
Before troubleshooting ................................35
Diagnostic LEDs ....................................36
Power On ........................................36
Fault ............................................36
Terminal Description ..................................37
Replacement Parts ...................................41
Index 42
Unconditional Warranty 47
iii
250-0288.qxd 6/9/00 1:05 PM Page iii
Illustrations
Figure 1. MMBOSS Series Dimensions ......................3
Figure 2. Speed Adjust Potentiometer Mounting ................9
Figure 3. Quick-Connect Terminal Plug .....................10
Figure 4. PCB Power, Fuse and Motor Connections ............13
Figure 5. Optional Switch Connections ......................15
Figure 6. Voltage Signal Follower Connections ................16
Figure 7. Sensor Feedback Connections ....................18
Figure 8. Jumper Locations ..............................19
Figure 9. Decelerate to Minimum Speed Switch ...............26
Figure 10. Calibration Trimpot Layout .......................27
Figure 11. Multiple Fixed Speeds ..........................31
Figure 12. Adjustable Speeds Using Potentiometers in Series ....32
Figure 13. Independent Adjustable Speeds ..................33
Figure 14. DIRECTION Switch ............................34
Figure 15. Diagnostic LED Location ........................36
Figure 16. Terminal Assignments ..........................37
iv
250-0288.qxd 6/9/00 1:05 PM Page iv
Tables
Table 1. Line Fuse Chart .................................8
Table 2. Replacement Parts ..............................41
v
250-0288.qxd 6/9/00 1:05 PM Page v
250-0288.qxd 6/9/00 1:05 PM Page vi
Maximum Phase Current (continuous) 5 ADC
DC Bus Voltage Input Range† 12 – 40 VDC
Maximum Phase Current Limit
1.5 times Maximum Phase Current (continuous)
Peak Phase Current Limit
2 times Maximum Phase Current (for 1 second)
Acceleration Time Range 6 seconds
Deceleration Time Range 6 seconds
Speed Regulation (typical) 0.06% of base speed
Speed Adjust Potentiometer 10K ohms
Analog Input Voltage Range (signal must be isolated) 0–10 VDC
Input Impedance 60K ohms
Power Device Switching Frequency (6–step, trapezoidal) 22 Khz
Hall sensor output , maximum +5 VDC @ 20mA
Vibration 0.5G max. (0–50 Hz); 0.1G max. (>50 Hz)
Weight 2 lb
Ambient Operating Temperature Range 0–40ºC
†Input voltage range is selected via SW501. Jumper terminals 1 and 2
for a voltage range of 15 - 40 VDC (this is the factory setting). Jumper
terminals 2 and 3 for 12 - 15 VDC input.
1
Specifications
250-0288.qxd 6/9/00 1:05 PM Page 1
250-0288.qxd 6/9/00 1:05 PM Page 2
Altri manuali per MMBOSS Series
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Minarik Azionamento CC
Minarik
Minarik C1XP02-115AC Manuale
Minarik
Minarik RG5500U Manuale utente
Minarik
Minarik MM20000 Series Manuale utente
Minarik
Minarik RG501A Manuale utente
Minarik
Minarik BOSS Series Manuale utente
Minarik
Minarik MM20000A Series Manuale utente
Minarik
Minarik VFDP4X04-D230-PCM Manuale utente
Minarik
Minarik NRGD-4Q Series Manuale utente
Minarik
Minarik Motor Master 20000 Series Manuale utente
Minarik
Minarik MMRG Series Manuale utente
Minarik
Minarik RG500 Series Manuale utente
Minarik
Minarik MM21036A Manuale utente
Minarik
Minarik NRG-2Q Series Manuale utente
Minarik
Minarik MMBOSS Series Manuale utente
Minarik
Minarik LV Series Manuale utente
Minarik
Minarik XP-AC Series Manuale utente
Minarik
Minarik DC30-12-4Q-L Manuale utente
Minarik
Minarik VFD Series Manuale utente
Minarik
Minarik M2 Manuale utente
Minarik
Minarik XP-AC-SL Series Manuale utente
Manuali Azionamento CC popolari di altre marche
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuale utente
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuale elenco delle parti
Chamberlain Garog
Chamberlain Garog D Series Manuale utente
Parker
Parker PDS Series Manuale utente
Festo
Festo DGC G Series Guida all'installazione
Binks
Binks QS-5012-1-CE Manuale utente
