Minarik XP-AC Series Manuale utente

Pulse-Width Modulated, Adjustable Speed Drives for DC Brush Motors

USER’S MANUAL

XP-AC SERIES

MODELS

XP02-115AC

XP05-115AC

XP10-115AC

Minarik Drives

without written permission from Minarik Drives. The information and technical data in this

manual are subject to change without notice. Minarik Corporation and its Divisions make no

warranty of any kind with respect to this material, including, but not limited to, the implied

warranties of its merchantability and tness for a given purpose. Minarik Corporation and its

Divisions assume no responsibility for any errors that may appear in this manual and make

no commitment to update or to keep current the information in this manual.

Printed in the United States of America.

m Safety Warnings

Have a qualied electrical maintenance technician install, adjust, and service this

equipment. Follow the National Electrical Code and all other applicable electrical and

safety codes, including the provisions of the Occupational Safety and Healthy Act

(OSHA) when installing equipment.

Reduce the chance of an electrical re, shock, or explosion by proper grounding, over

current protection, thermal protection, and enclosure. Follow sound maintenance

procedures.

It is possible for a drive to run at full speed as a result of a component failure. Install a

master switch in the AC line for stopping the drive in an emergency.

This drive is not isolated from earth ground. Circuit potentials are at 115 VAC above

earth ground. Avoid direct contact with the printed circuit board or with circuit elements

to prevent the risk of serious injury or fatality. Use a non-metallic screwdriver for adjust-

ing the calibration trimpots.

•

Table of Contents

Specications 1

Dimensions 2

Installation 3

Mounting...............................................................3

Wiring..................................................................3

Heatsinking ............................................................4

LineFusing .............................................................4

Speedadjustpotentiometer ...............................................5

Connections ............................................................6

VoltageFollower .........................................................7

Operation 8

Startup.................................................................8

Linestartingandlinestopping .............................................8

Deceleratingtoastop ....................................................9

Dynamicbraking........................................................10

Calibration 12

MAXSPD..............................................................12

ACCEL/DECEL..........................................................12

IRCOMP...............................................................12

CURRENTLIMIT.........................................................13

ApplicationNotes 15

Multiple Fixed Speeds ...................................................15

Adjustable speeds using potentiometers in series. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Independentadjustablespeeds...........................................16

iii

RUN/JOGswitch........................................................16

ConnectiontootherMinarikdevices........................................17

Leader-followerapplication ...............................................18

Single speed potentiometer control of multiple drives . . . . . . . . . . . . . . . . . . . . . . . . . 18

Reversing..............................................................19

Troubleshooting 20

Replacement Parts 23

Limited Warranty inside back cover

iviv

Illustrations

Fig1.XP-ACSeriesDimensions ................................................2

Fig2.SpeedAdjustPotentiometer..............................................5

Fig3.XP-ACConnections......................................................6

Fig4.VoltageFollowerConnection..............................................7

Fig5.Run/DeceleratetoZeroSpeedSwitch......................................9

Fig6.DynamicBrakeConnection..............................................10

Fig 7. Typical CURRENT LIMIT and IR COMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fig 8. Multiple Fixed Speeds ..................................................15

Fig 9. Adjustable Fixed Speeds using Potentiometers in Series ......................15

Fig 10. Independent Adjustable Speeds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Fig 11. RUN/JOG Switch Connection to Speed Adjust Potentiometer . . . . . . . . . . . . . . . . . 16

Fig 12. Connecting an XP-AC Series Drive to a PCM4 or DLC600 . . . . . . . . . . . . . . . . . . . . 17

Fig13.Leader-FollowerApplication ............................................18

Fig 14. Single Speed Potentiometer Control of Multiple Drives . . . . . . . . . . . . . . . . . . . . . . 18

Fig15.ReversingCircuitConnection ...........................................19

Specications

Max. Continuous Armature HP Range with

Model  ArmatureCurrent(AmpsDC) 115VACApplied

XP02-115AC

XP05-115AC

XP10-115AC

10 †

1/20 - 1/8

1/4 - 1/2

1/2 - 1

ACLineVoltage

ArmatureVoltageRange

Form Factor (at base speed)

Acceleration/Deceleration Time Range (no load)

AnalogInputVoltageRange[isolated;S1(+)toS2(–)]

InputImpedence(S1toS2with5VDCinput)

Speed Regulation

SafetyCertication

Ambient Temperature Range (chassis drive)

Weight

XP02-115AC

XP05-115AC

XP10-115AC

115VAC,±10%,50/60Hz,singlephase

0–130VDC

1.05

0.5-6seconds

0–10VDC

approximately10Kohms

1%basespeedorbetter

ULRecognizedComponent,le#E132235

CSACertiedComponent,le#LR41380

10°C–40°C

0.66lb

0.72 lb

0.82 lb

† Use heat sink part number 223-0159 when operating the drive above 5 ADC.

Dimensions

0.73 [19]

1.75 [44]

3.64 [93]

4.30 [109]

3.80 [97]

0.19 [5]

6 PLACES

A-

A+

+ DC IN

- DC IN

R501

R504 R502

CURRENT

LIMIT

MAX SPEED

ACCEL /

DECEL

IR COMP

R503

C501

1.03 [26]

1.35 [34]

0.19 [5]

SIX MOUNTING SLOTS

0.19 [5] WIDE x 0.34 [9] DEEP

MODEL

XP02-115AC

XP05-115AC

XP10-115AC

DIMENSION “A”

1.77 [45]

2.36 [60]

2.88 [73]

FIGURE1.XP-ACSeriesDimensions

Installation

Mounting

Drive components are sensitive to electrostatic elds. Avoid contact with the circuit

board directly. Hold drive by the chassis only.

Protect the drive from dirt, moisture, and accidental contact. Provide sufcient room for

access to the terminal block and calibration trimpots.

Mount the drive away from the other heat sources. Operate the drive within the speci-

ed ambient operating temperature range.

Prevent loose connections by avoiding excessive vibration of the drive.

Mount drive with its board in either a horizontal or vertical plane. Six 0.19 in. (5 mm)

wide slots in the chassis accept #8 pan head screws. Fasten either the large base or

the narrow ange of the chassis to the subplate.

The Chassis must be earth grounded. Use a star washer beneath the head of at least

one of the mounting screws to penetrate the anodized chassis surface and to reach

bare metal.

Wiring

Use 18 AWG wire for speed adjust potentiometer wiring. Use 16 AWG wire for motor

wiring.

Twist logic wires (for speed adjust potentiometer) to avoid picking up unwanted electri-

cal noise. Use shielded cable if wires are longer than 18 in. (46 cm).

Keep logic wires away from power carrying lines or sources of electrical noise that

can cause erratic operation. Never run speed adjust potentiometer wires in the same

conduit used for motor and AC line voltage wires.

•

4 Installation

It may be necessary to earth ground the shielded cable. If noise is produced by devices

other than the drive, ground the shield at the drive end. If noise is generated by a

device on the drive, ground the shield at the end away from the drive. Do not ground

both ends of the shield.

Keep logic wires away from the power carrying lines or sources of electrical noise that

can cause erratic operation.

Heat sinking

Model XP10-115AC requires an additional heat sink when the continuous armature cur-

rent is above 5 ADC. Use Minarik®part number 223-0159. All other chassis drives have

sufcient heat sinking in their basic congurations. Use a thermally conductive heat sink

compound (such as Dow Corning®340 Heat Sink Compound) between the drive chassis

and heat sink surface for optimum heat transfer.

Line fusing

Protect all Minarik drives with AC line fuses. Use fast acting AC line fuses rated for 250

volts, and approximately 150% – 200% of the maximum armature current. Fuse only the

“hot” side of the AC line (L1) if using 115 VAC line voltage. See the chart below for recom-

mended line fuse sizes.

•

Maximum Armature

Current (DC Amps)

1.5 & below

2.6

3.5

5.0

7.6

AC Line Fuse

Rating (AC Amps)

RecommendedLineFuseSizes

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Minarik Azionamento CC

Minarik

Minarik HTL05-D-4Q Manuale utente

Minarik

Minarik MM300 Series Manuale utente

Minarik

Minarik C1XP02-115AC Manuale

Minarik

Minarik M2 Manuale utente

Minarik

Minarik MMBOSS Series Manuale utente

Minarik

Minarik XP-AC-SL Series Manuale utente

Minarik

Minarik XL1100A Manuale utente

Minarik

Minarik BOSS Series Manuale utente

Minarik

Minarik PCM21000A Manuale utente

Minarik

Minarik NRGD-4Q Series Manuale utente

Minarik

Minarik MMRG Series Manuale utente

Minarik

Minarik NRG-2Q Series Manuale utente

Minarik

Minarik RG500 Series Manuale utente

Minarik

Minarik RG5500U Manuale utente

Minarik

Minarik Motor Master 20000 Series Manuale utente

Minarik

Minarik MMRG30U Manuale utente

Minarik

Minarik M2-D Manuale utente

Minarik

Minarik MMBOSS Series Manuale utente

Minarik

Minarik MM21036A Manuale utente

Minarik

Minarik MM-PCM Series Manuale utente

Minarik

Minarik PCM23000A Series Manuale utente

Minarik

Minarik MM20000A Series Manuale utente

Minarik

Minarik LV Series Manuale utente

Minarik

Minarik BOSS Series Manuale utente

Manuali Azionamento CC popolari di altre marche

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuale utente

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuale elenco delle parti

Chamberlain Garog

Chamberlain Garog D Series Manuale utente

Parker

Parker PDS Series Manuale utente

Festo

Festo DGC G Series Guida all'installazione

Binks

Binks QS-5012-1-CE Manuale utente

Danfoss

Danfoss VLT 2800 Series Scheda tecnica

ABB

ABB ACQ580-01 Series Manuale di installazione

YASKAWA

YASKAWA CANopen SI-S3 Manuale utente

GE D20A6 Manuale utente

Unex

Unex MC-D-250-1000-050W-TW Manuale utente

Geckodrive

Geckodrive G213V Manuale utente

ABB

ABB RSYC-01 Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale del proprietario

WEG

WEG DeviceNet CFW500 Manuale utente

Siemens

Siemens SINAMICS G Scheda tecnica

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Istruzioni operative

SOMFY

SOMFY JR RU 30 Manuale utente