Minka Group Minka Aire GEANT Guida

1. Before you begin installing the fan, shut power off at the circuit breaker of the fuse box.

2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrial connections comply with local codes, ordinance, or National Electriacl Codes. Hire a qualiﬁed electrician

or consulf a do-it-yourself wiring handbook if you are unfamiliar with installing electrial wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance

of 7 feet from the ﬂoor and 18 inches from the tip of the blades to the wall.

5. NOTE: THIS CEILING FAN EXCEEDS THE MAXIMUM WEIGHT SPECIFIED BY UL FOR HANGING FROM A STANDARD OUTLET BOX.

SPECIAL REINFORCEMENT OF THE CEILING IS REQUIRED FOR INSTALLATION.

6. CAUTION: Use the wood screws provided for fan installation. The wood screws must go through the outlet box via the knock outs

and secured directly to the building joist.

7. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

8. Do not insert anything into the fan blades while the fan is operating.

9. Turn the fan off and wait for the blades to stop completey before cleaning or performing

any maintenance.

SUPPORT DIRECTLY FROM BUILDING STRUCTURE.

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN DIRECTLY TO THE BUILDING JOIST USING THE WOOD SCREWS

AND WACHERS PROVIED WITH THE FAN. THE WOOD SCREWS MUST GO THROUGH THE OUTLET BOX VIA THE KNOCK OUTS. CONSULT A QUALIFIED

ELECTRICIAN IF DOUBT.

Hanger bracket (Hanger bracket

support included)

Standard downrod assembly (16”)

Hanger bracket plate

Canopy

Canopy cover

Coupling cover

Fan motor/ housing assembly

Wheel

LED light kit

Switch cover

Blade tips (8)

Fan Blade (8)

Blade holder (8)

Receiver

Remote control with holder

and 2 mounting screws

12V MN21/A23 battert

Balancing kit

Mounting hardware:

M6.5x89mm wood screws(3pcs)

Ø6.5x19mm Flat washers(3pcs)

6.5mm Star washers(3 pcs)

Wire nutes(3 pcs)

Hex nuts(3 pcs)

1/4” spring washers(3pcs)

1/4” Flat washer (3pcs)

1/4”x 3/8”Screws with lock washers(9pcs)

1/4”x 5/8”Screws with lock washers(25pcs)

1/4”x 5/8”Screws with lock washers(17pcs)

1/4”x 1/2”Screws with lock washers(33pcs)

Ø6.4x22mm Flat washers(33pcs)

5/32”x3/16” Screws(9pcs)

Extension safety cable

Extending wires (24”+24”with pin connector)

ownrod rubber cover (assembly in

standard downrod)

I .

10.

11.

12.

13.

14.

15.

16.

17.

14 15

CAUTION! THE HANGER BRACKET PLATE MUST BE INSTALLED DIRECTLY

TO THE BUILDING JOIST USINGTHE TWO WOOD SCREWS AND WASHERS

PROVIDED.

Step1. Remove two knock-outs from the oulet box to expose the joist. (Fig. 5)

Step2. Use the two wood screws and washers provided to secure the hanger

bracket plate to the building joist via the knockout holes from the outlet box. (Fig. 6)

Step3. Secure hanger bracket to hanger bracket plate using the two hex nuts and

washers provided, make sure nuts are securely tighten. (Fig. 7)

Step4. Loosen the two set screws and remove the hitch pin and lock pin from the

coupling located on the top of motor assembly. (Fig. 8)

Step5. Remove hanger ball from downrod assembly by loosening set screws,

removing the cross pin, and sliding ball off rod. (Fif. 9)

Step6. Carefully feed fan wires up through the downrod. (Fig. 10) Thread the rod

into the coupling until the holes line up holes and replace lock pin and hitch pin.

Tighten set screws.

Step7. Slip coupling cover, and canopy cover, and canopy onto downrod. (Fig. 11)

Carefully reinstall hanger ball onto rod being sure that cross pin is in the correct

position, set screws are tighten and wires are not twisted.

Step8. Place downrod rudder cover onto the hanger ball. (Fig. 11)

Step9. Lift the motor assembly and place hanger ball into the hanger bracket. Rotate

the motor assembly as needed until the check groove from the hanger ball rests firmly

over the registration tab from the hanger bracket. Motor assembly should not rotate if this

is done correctly. (Fig.12)

Step10. Secure the safety cable to the building structure using a wood screw.

If necessary, connect the extension safety cable to the safety cable (from fan), feed end of

cable into clamp hole and firmly tighten screw, as noted in the circle insert of Fig.12

Altri manuali Minka Group Fan

Minka Group

Minka Group MinkaAire Dyno-XL Guida

Minka Group

Minka Group minkaAire ALUMA Guida

Minka Group

Minka Group Minka-Aire Kewl F833 Manuale utente

Minka Group

Minka Group minkaAire CONCEPT I Guida

Minka Group

Minka Group Minka-Aire Espace Manuale utente

Minka Group

Minka Group Aire Roxhill Manuale utente

Minka Group

Minka Group minkaAire Contractor WATT F551 Manuale utente

Minka Group

Minka Group minkaAire Sundance F572-ORB Manuale utente

Minka Group

Minka Group minkaAire DELANO II Guida

Minka Group

Minka Group Minka-Aire Java LED F753L-WHF Manuale utente

Minka Group

Minka Group minkaAire DECO Guida

Minka Group

Minka Group minkaAire CONCEPT III Guida

Minka Group

Minka Group minkaAire CONCEPT IV Guida

Minka Group

Minka Group minkaAire Contractor Series Manuale utente

Minka Group

Minka Group Aire Roto F524 Guida

Minka Group

Minka Group minkaAire SKYHAWK Guida

Minka Group

Minka Group MinkaAire Java Manuale utente

Minka Group

Minka Group minkaAire Ninety-Nine F899L-ORB Manuale utente

Minka Group

Minka Group Minka-Aire Symbio Manuale utente

Minka Group

Minka Group minkaAire CONCEPT II WET Manuale utente

Minka Group

Minka Group Minka Aire Sabot Guida

Minka Group

Minka Group F516L-WH Guida

Minka Group

Minka Group minkaAire GEORGE KOVACS SPECTRE Guida

Minka Group

Minka Group MinkaAire Mesa F566 Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio