MINOLTA-QMS 2060 Manuale utente
SP-A310
Service
&
Parts Manual
September 1996
+-’
Revision C-02
WARNING LABELS
-
i
SAFETY
INFORMATlON
.
ALL Areas
INTERNAL LASER RADIATION
Maximum radiation power: 8.8 x
lo4
(W)
Wavelength: 770-8 10 MI
This is a Class
Bib
Laser Diode Assy. that has an invisible Laser Beam. The Print Head
Unit is NOT A FIELD SERVICE ITEM. Therefore, the Print Head Unit should not be
opened under any circumstances.
U.S.A. Only
LASER SAFETY
This LBP printer is certified as a Class 1 laser product under the U.S. Department of Health
and Human Services
(DHHS)
Radiation Performance Standard according to the Food, Drug
and Cosmetic Act of 1990. This means that the LBP printer does not produce hazardous laser
radiation.
Since radiation emitted inside the LBP printer is completely confined within protective
housing and external covers, the laser beam cannot escape from the LBP printer during
any phase of user operation.
CDRH REGULATIONS
The Center for Devices and
R&ological
Health (CDRH) of the U.S. Food and Drug
Administration implemented regulations for laser products on August 2, 1976. These
regulations apply to laser products manufactured from August 1, 1976. Compliance is
mandatory for products marketed in the United States. The label shown in the figure
indicates compliance with the CDRH regulations and must be attached to laser products
marketed in the United States-.
CLASSIFICATION OF THE LASER PRODUCT
This product is classified as a Class 1 Laser Product under the CDRH Regulations U.S.A..
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Discard
used
batteries according to manufacture’s instructions.
ii
Denmark Only
ADVARSEL!
.
Lithiumbatteri-Eksplosionsfare ved
fejlagtig
hhdtering.
Udskifining
m4
kun ske med
batteri
af
samme
fabrikat og type.
Lever det brugte batter-i tilbage
til
leverandoren.
Norway Only
ADVARSEL
Lithiumbatteri-Bksplosjonsfare.
Ved
utskifting
benyttes kun batter-i som anbefalt av apparatfabrikanten.
Brukt
batteri
retumeres
apparatleverand@ren.
Sweden Only
-.
VARNING
(
Explosionsfara
vid felaktigt
bat&byte.
AMind
samma
batterityp
eller
en ekvivalent
typ
som rekommenderas av
apparativerkaren.
Kassera
anvXnt
batter-i enligt fabrikantens
in&&ion.
VARNING!
Osynlig laserstr&ting
n3r
denna
de1
ar
oppnad
och
sp&-ren
2r
urkopplad.
Behakta ej
St&en.
Finland Only
VAROITIJS
Pristo voi
r&jahM
jos se on
virheellisesti
asennettu.
Vaihda
paristo
ainoastaan
laitevalmistajan
suosittelemaan
tyyppiin.
H&vita
tiytetty
paristo
valmistajan
ohjeiden
mukaisesti.
.,
1-
VARO!
Avattaessa ja suojalulcitus
ohitettasessa
olet
ahtiina
n&ymatt(lmtie
lasersateilylle.
&4
katso
sateeseen.
New Zealand Only
Warning
“Immediately disconnect the equipment should it become physically damaged, and arrange
for its disposal or repair before reconnecting.”
“Disconnect the Telecom Network connection before disconnecting the Power connection
prior to relocating the equipment, and reconnect the Poker first.”
User Instruction (For all users)
The outlet should be located near the printer and should be easily accessible.
.
.
.
III
>,.--
)‘
1
_-
C
.
Please read the following for your own protection.
I
A
Caution
1
Opening the cover indicated by the
Caution
label below may expose you to
harmful laser radiation which could cause damage or loss of eyesight. Do
not
Open the Cover
when the power is on.
iv
PRECAUTIONS
(1)
Precautlbns
Refer to D: DISASSEMBLY/CLEANING for the Disassembly procedure.
Be sure to unplug the
printer
befcre disassembling and
cleauing.
pczzi&q
1. When unplugging
ccumec
tors on the P.WI3.s themselves, always make
sum
the power is OFF first.
2.
Always unplug conrxctors by holding the connector housing. Pulling on the power cord can lead
to problems with poor contact.
3.Itisrec
canmended
that a body ground not be used when carrying out any trouble-shooting
procedure. Be sure to ground DC lines to a ground test point on the P.W.B.
(2) At Replacement/ Adjustment/ Cleaning
pGiq
l.BesuretohandletheFusingUnitcarefullyastheunitisstillhotforawhileafbertheprinteris
stopped-
;-
2.
Do not disassemble the Imaging Cartridge or the Print Head Unit
t
:
3.UseonlyaPuseoftheindicatedrating.
(3)
During
Operation
A
Caution
1. Keep your hands. clothing, etc. well away from operating or rotating
parts.
2.
Never touch the
temhals
d
electrical parts or high voltage parts.
3.Thisprinbuisusinganinvisiblelaserbeam.Topleventalaserbeamleak.theprintermaLesatri~
runtobesurethecoversarein@tion.
HANDLING THE P.W.B.
Observe
the folIowing precautions when handling a P.W.B. with
ICs.
(1)
During Transportation/ Storage
i:
1. During transport and storage,
P.WB.s
should be kept
incarductive
bags or on mats and not
taken
out
lmkss
absolutely
rEce.ssary.
2.
P.WBs
should be stored in a place where direct sunlight
does
not
strike
them.
3.Don0ttouch1Ctermin&withyourhands.
(2) At Replacement
1. Before removing connectors from a
P.WB..
make sure
the
printer has been ~npluggcd
2. When
P.WB.s
are
taken
out of their conductive bags or off their mats, hold them by
t&sir
edges to
avoid touching
the
term&Is
or the patterned surfaces.
3.BeforeinstallingumnectcrsonaP.WB..makesuretheprinterhasbeenunplugged.
(3)
At Inspection
1. Avoid checking a P.WB. with testers; instead, use
operating
pa.tQ
of
the
printer. mdicatrx
ktrps,
and other means to evaluateoperational
umditions.
2.
Be careful not to short-circuit
IC
terminals
when
using metal instruments or screws.
3. If it is necessary to touch elements on
the
P.W.B. with your hand, make
sure
your body is properly
5&d
V
CONTENTS
A: PRODUCT INSTALLATION
1.
PRECAUITON FOR INSTALLATION ......................................................................................
A- 1
l-l. Installation Site
...................................................................................................................
A-l
1-2.
Ekonmental
Requirementi
.............................................................................................
A-l
l-3.
Power
Rquirements ...........................................................................................................
A-l
2.
INSTALLATION .........................................................................................................................
A- 1
2-l.
cannectioa ..........................................................................................................................
A-l
2-2.
space
Requirements
............................................................................................................
A-2
B: GENERAL INFORMATION
1.
SPECIFICATIONS
......................................................................................................................
B-l
2.
PARTS IDENTIFICATION ......................................................................................................... B-3
3. COMPONENT LAYOUT ............................................................................................................ B-4
4. GEARS/ ROLLERS ASSIGNMENT .......................................................................................... B-5
5.
ELECTRICAL
CfX4POMENT
LAYOUT
..................................................................................
B-6
6.
CONNEcroRs
LAYOUT
........................................
.
................................................................. B-7
7.
SWlXElES/
SENSORS IDEN’IlFICA&N
$.
_,
:a..
....................................................... ........... B-8
8.
ELECl.RlCAL
SERVICE
PARTS
ON P. W.
BOARDS .............................................................. B-9
9.
SYSTEM
LAYOUT
................................................................................................................... B-10
9-l. Drive Se&m
....................................................................................................................
B-10
9-2.ElectridSection
................................................................
..-
.......................................... B-11
10. SEQUENCE FLOW
.................................................................................................................. B-12
11.
CIRCUITDIAGRAM .............................................................................................................. B-13
vi
Indice
Altri manuali MINOLTA-QMS Stampante
MINOLTA-QMS
MINOLTA-QMS ENord magicolor 3100 Manuale utente
MINOLTA-QMS
MINOLTA-QMS PagePro 9100 Guida rapida
MINOLTA-QMS
MINOLTA-QMS PagePro 4100W Manuale utente
MINOLTA-QMS
MINOLTA-QMS PagePro 4100 Manuale utente
MINOLTA-QMS
MINOLTA-QMS 4060 Istruzioni per la costruzione
MINOLTA-QMS
MINOLTA-QMS PagePro 4100E Manuale utente
MINOLTA-QMS
MINOLTA-QMS 2560 Manuale utente
MINOLTA-QMS
MINOLTA-QMS magicolor 2300 DL Manuale utente
MINOLTA-QMS
MINOLTA-QMS magicolor 2300 DL Manuale utente
MINOLTA-QMS
MINOLTA-QMS ENord magicolor 3100 Manuale utente
MINOLTA-QMS
MINOLTA-QMS Magicolor 2210 GN Manuale utente
MINOLTA-QMS
MINOLTA-QMS Magicolor 2200 DeskLaser Manuale
MINOLTA-QMS
MINOLTA-QMS Magicolor 2300W Manuale
MINOLTA-QMS
MINOLTA-QMS PagePro 1250E Manuale utente
MINOLTA-QMS
MINOLTA-QMS magicolor 2350 Manuale utente
MINOLTA-QMS
MINOLTA-QMS PagePro 1200 Series Manuale utente
MINOLTA-QMS
MINOLTA-QMS PagePro 9100 Manuale utente
MINOLTA-QMS
MINOLTA-QMS PagePro 1100L Manuale utente
MINOLTA-QMS
MINOLTA-QMS PagePro 9100 Series Manuale utente
MINOLTA-QMS
MINOLTA-QMS Magicolor 6100 Manuale operativo
