MINOURA 971-3 Manuale utente
Bicycle Display Stand 971-3 instructions manual
(ver.2.4 2019/4)
!
Thank you for choosing Minoura 971-3.
Read this instructions carefully to understand well how this stand is constructed before starting assembling.
- 1 -
800mm
520mm
270mm
920mm
850mm
Completed image and dimensions of 971-3
(in the settings the bikes facing rightward)
IMPORTANT NOTES
• For standard 2-wheel bike only. No recumbent, tandem and any other type of bikes.
• For 24-inch wheel or larger only. Any bike with smaller wheel such as BMX or juvenile bike, and a special bike
with too low bottom bracket height or carbon monocoque frame may not t to this stand.
• In the case of electric bike, the weight is limited under 30 kgs each.
• The bike is supported at just 3 points; front tire, rear tire and the bottom bracket. Adjust the BB Support height
precisely in each case to expect maximum stability.
• The bike direction is xed as per the Stair Frame direction. Wrong direction cannot mount the bike properly.
• Do not step on this stand. The stand body is not so durable to support your weight.
• Setup this stand on horizontal and level oor, especially when installing the optional Caster Kit.
• When moving this stand, get off all bikes from the stand before action.
• Check regularly if each bolt and nut are rmly tightened.
Contact MINOURA JAPAN
134-1 Shimomiya, Godo, Anpachi, Gifu 503-2312 Japan
Fax: +81-584-27-7505
Mail: [email protected]
Web: www.minoura.jp
Made in Japan
1
2
3
!
!
To avpoid stain to the oor or carpet, put the supplied
round transparent lm on each back of Foot Adjuster.
4
!
5
- 2 -
How To Assemble 971-3
Required Tools: 1 x Phillips Screwdriver (#2), 2 x 13mm Socsket Wrench
First of all, check all small parts are correctly prepared.
Parts List
2 x Base Frame 4 x Round Head Screw M5x40
3 x Stair Frame 3 x Hex Head Bolt M8x30
2 x Pillar-S (223mm) 6 x Hex Head Bolt M8x35
2 x Pillar-M (473mm) 8 x Hex Head Bolt M8x45
2 x Joint Frame 2 x Hex Head Bolt M8x60
3 x B.B. Support 15 x Metal Collar (short)
6 x Tire Cradle 6 x Metal Collar (long)
4 x Foot Adjuster 4 x M5 Spring Washer
21 x M8 Spring Washer
21 x M8 Flat Washer
8 x M8 Nut
Assemble 2 sets of the Side Frame.
Connect the Pillar S (223mm) and the Pillar-M (473mm)
with the Joint Frame. Tighten the screw to fix.
Pillar-M
(473mm)
Joint Frame
Pillar-S
(223mm)
M5x40 Screw
M5 Spring Washer
Make sure the direction of Pillar-M.
Joint Frame must be parallel when
standing both pillars.
Assemble the Base Frame with each Side Frame.
Install the Foot Adjusters on both ends of the Base Frame.
Base Frame
Foot Adjuster
Collar (long)
M8 Flat Washer
M8 Spring Washer
Hex Bolt M8x45
Connect both Side Frames with three (3) Stair Frames.
On the 1st level Stair Frame, you use longer M8x60 bolt.
Hex Bolt M8x60
M8 Spring Washer
M8 Flat Washer
Collar (short)
Stair Frame
Collar (long)
M8 Flat Washer
M8 Spring Washer
M8 Nut
Make sure there are two (2) holes on each Stair
Frame for mounting the Bottom Bracket Support.
To set the bike heading right, place the Stair
Frame to have the holes in left side.
Install the Stair Frames on the 2nd and 3rd levels.
Set all frames in the same direction if you wish to set the
bikes in same direction.
Hex Bolt M8x45
M8 Spring Washer
M8 Flat Washer
Collar (short) Stair Frame
｝
｝
Long
Short
Bike Direction
6
!
7
- 3 -
!
Install a pair of Tire Cradles on each Stair Frame.
Each Tire Cradle is position adjustable in 5 points in order to fit
various sizes of bike wheelbase.
To expect maximum stability of bikes, choose the best position
each by each.
Tire Cradle
Hex Bolt M8x35
Collar (short)
M8 Flat Washer
M8 Spring Washer
M8 Nut
When mounting short wheelbase
bike, turn Tire Cradle that the
bolt head comes through the
larger hole.
Install the Bottom Bracket Support to the Stair Frame.
Be sure there are two (2) holes on the Stair Frame.
The center hole is for short wheelbase bike. The further hole is for standard bike.
Put the triangle bracket between the chain-stays and support the down-tube with
the U-shaped bracket.
If you mount the bike in wrong direction
against you set on the Stair Frame, the
wheels will have to come off from the Tire
Cradles.
Make sure the bike direction follows the
stand direction.
B.B. Support
For standard wheelbase bike
For short wheelbase bike
Collar (short)
M8 Flat Washer
M8 Spring Washer
Hex Bolt M8x30
- 4 -
How To Mount Bike on 971-3
1
2
3
4
Place the bike on the floor in the same direction you set on the Stair Frame.
Place both front and rear tire on the Tire Cradles.
While supporting the bike with hand, loosen the knob bolt on the B.B. Support, and extend the upper support until it
touches the bottom bracket.
After confirming the bike is stably supported that the U-shaped part holds the down-tube and the triange guide is put
between the chain-stays, tighten the knob bolt to hold the position.
5In the end, shake the bike side to side to confirm the bike is stably supported, then leave from the stand.
Optional Items
By replacing the Foot Adjuster to a caster wheel, you can
move 971-3 to anywhere while mounting bikes on it.
Caster Kit contains a reinforcement bar and beam rods to
keep the frame solid and stable.
The reinforcement bar will be installed under Pillar-M
(473mm).
Caster Wheel
Model Variation
By combining 971-3 and 971-3H,
you can use them as a one unit
for totally 6 bikes.
If you cannot hold the bike on 971-3 stable due to the
special frame shape such as carbon monocoque or a
battery for electric shifting device sits near the bottom
bracket, you need to add this wheel holder between the tire
cradle and the frame instead of using the B.B. Support.
This cradle holds the whole rear wheel.
Caster Kit Rear Wheel Support
971-4 971-3H
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali MINOURA Rack e supporto
MINOURA
MINOURA GravityStand-2 Manuale utente
MINOURA
MINOURA VERGO EXCEL-L Manuale utente
MINOURA
MINOURA DS-110 DS-100H Manuale utente
MINOURA
MINOURA P-500AL-2 Manuale utente
MINOURA
MINOURA W-300 Manuale utente
MINOURA
MINOURA TRUE-PRO Manuale utente
MINOURA
MINOURA DW-2 Manuale utente
MINOURA
MINOURA P-700X Manuale utente
MINOURA
MINOURA DSX-1 Manuale utente
MINOURA
MINOURA WORKMAN PRO Manuale utente
MINOURA
MINOURA VERGO EXCEL-S Manuale utente
MINOURA
MINOURA BIKE PIT Manuale utente
MINOURA
MINOURA DS-2200 Manuale utente
MINOURA
MINOURA BikeTower10 Manuale utente
MINOURA
MINOURA P-700X Manuale utente
MINOURA
MINOURA LEVEL-170 Manuale utente
MINOURA
MINOURA DS-520 - ASSEMBLY Manuale utente
MINOURA
MINOURA T-817 Manuale utente
MINOURA
MINOURA BikeTower 25D Manuale utente
MINOURA
MINOURA FCG-310 - MANUAL 2 Manuale utente
