Mitsubishi M80 series Guida all'installazione

Introduction

This manual covers the items required for installing, connecting and setting up the MITSUBISHI CNC.

Supported models are as follows:

Read this manual thoroughly and understand the product's functions and performance before starting to use.

This manual is written on the assumption that all optional functions are added, but the actually delivered device may

not have all functions.

The unit names, cable names and various specifications are subject to change without notice. Please confirm these

before placing an order.

Be sure to keep this manual always at hand.

This manual notes a reference chapter as "Chapter: Section: Paragraph".

(Example) For "4.1.1 Environment Conditions inside the Control Panel" :

"General Specifications: Environment Conditions: Environment Conditions inside the Operation"

("4.1.1 Environment Conditions inside the Operation" included in "4.1 Environment Conditions" of "4 General

Specifications")

Notes on Reading This Manual

(1) This book is configured as follows.

Refer to the following chapters as necessary.

Installation and connection: Chapter 1 to 15

Setup: Chapter 16 to 30

(2) This manual explains general parameters as viewed from the NC.

For information about each machine tool, refer to manuals issued from the machine tool builder.

If the descriptions relating to "restrictions" and "allowable conditions" conflict between this manual and the

machine tool builder's instruction manual, the later has priority over the former.

(3) This manual is intended to contain as much descriptions as possible even about special operations.

The operations to which no reference is made in this manual should be considered "impossible".

(4) This manual is for the machine tool builders who set up the NC system.

(5) Do not connect to the pin described as "NC" on the pin assignment table of the connector.

Supported models Abbreviations in this manual

M800S Series M800 Series, M800, M8

M80 Series M80 Series, M80, M8

For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by

the machine tool builder takes precedence over this manual.

Items that are not described in this manual must be interpreted as "not possible".

This manual is written on the assumption that all the applicable functions are included.

Some of them, however, may not be available for your NC system.

Refer to the specifications issued by the machine tool builder before use.

Refer to the Instruction Manual issued by each machine tool builder for details on each machine tool.

Some screens and functions may differ depending on each NC system (or version), and some functions

may not be possible. Please confirm the specifications before starting to use.

Refer to "Smart safety observation" (BNP-C3072-022) for details about the connection with safety

observing I/O device.

Do not connect NC system to the Internet-connected network.

To maintain the safety of the NC system against unauthorized access from external devices via the

network, take appropriate measures.

The numerical control unit is configured of the control unit, display unit, operation board (operation panel I/O unit),

servo drive unit, spindle drive unit, power supply unit + driver, servomotor, spindle motor, etc.

In this manual, the following items are generically called "controller".

- Control unit

- Display unit

- Operation board (operation panel I/O unit)

- Numerical control unit peripheral devices (input/output unit, safety unit)

In this manual, the following items are generically called "drive unit".

- Servo drive unit

- Spindle drive unit

- Power supply unit + driver

In this manual, the following items are generically called "motor".

- Servo motor

- Spindle motor

Also refer to the manuals on "Manual List" as necessary.

CAUTION

Manual List

Manuals related to M800/M80/C80 Series are listed as follows.

These manuals are written on the assumption that all optional functions are added to the targeted model.

Some functions or screens may not be available depending on the machine or specifications set by MTB. (Confirm the

specifications before use.)

The manuals issued by MTB take precedence over these manuals.

Manual IB No. Purpose and Contents

M800/M80 Series

Instruction Manual IB-1501274 - Operation guide for NC

- Explanation for screen operation, etc.

C80 Series

Instruction Manual IB-1501453 - Operation guide for NC

- Explanation for screen operation, etc.

M800/M80/C80 Series

Programming Manual

(Lathe System) (1/2)

IB-1501275 - G code programming for lathe system

- Basic functions, etc.

M800/M80/C80 Series

Programming Manual

(Lathe System) (2/2)

IB-1501276 - G code programming for lathe system

- Functions for multi-part system, high-accuracy function, etc.

M800/M80/C80 Series

Programming Manual

(Machining Center System) (1/2)

IB-1501277 - G code programming for machining center system

- Basic functions, etc.

M800/M80/C80 Series

Programming Manual

(Machining Center System) (2/2)

IB-1501278 - G code programming for machining center system

- Functions for multi-part system, high-accuracy function, etc.

M800/M80/C80 Series

Alarm/Parameter Manual IB-1501279 - Alarms

- Parameters

Manuals for MTBs (NC)

Manuals for MTBs (drive section)

Manual IB No. Purpose and Contents

M800/M80/C80 Series

Specifications Manual (Function) IB-1501505 - Model selection

- Outline of various functions

M800/M80/C80 Series

Specifications Manual (Hardware) IB-1501506 - Model selection

- Specifications of hardware unit

M800W/M80W Series

Connection and Setup Manual IB-1501268 - Detailed specifications of hardware unit

- Installation, connection, wiring, setup (startup/adjustment)

M800S/M80 Series

Connection and Setup Manual IB-1501269 - Detailed specifications of hardware unit

- Installation, connection, wiring, setup (startup/adjustment)

C80 Series

Connection and Setup Manual IB-1501452 - Detailed specifications of hardware unit

- Installation, connection, wiring, setup (startup/adjustment)

M800/M80 Series

PLC Development Manual IB-1501270

- Electrical design

- I/O relation (assignment, setting, connection), field network

- Development environment (PLC on-board, peripheral

development environment), etc.

M800/M80 Series

PLC Programming Manual IB-1501271

- Electrical design

- Sequence programming

- PLC support functions, etc.

M800/M80/C80 Series

PLC Interface Manual IB-1501272 - Electrical design

- Interface signals between NC and PLC

M800/M80 Series

Maintenance Manual IB-1501273 - Cleaning and replacement for each unit

- Other items related to maintenance

C80 Series

Maintenance Manual IB-1501454 - Cleaning and replacement for each unit

- Other items related to maintenance

Manual IB No. Contents

MDS-E/EH Series

Specifications Manual IB-1501226 - Specifications for power supply regeneration type

MDS-E/EH Series

Instruction Manual IB-1501229 - Instruction for power supply regeneration type

MDS-EJ/EJH Series

Specifications Manual IB-1501232 - Specifications for regenerative resistor type

MDS-EJ/EJH Series

Instruction Manual IB-1501235 - Instruction for regenerative resistor type

MDS-EM/EMH Series

Specifications Manual IB-1501238 - Specifications for multi-hybrid, power supply regeneration type

MDS-EM/EMH Series

Instruction Manual IB-1501241 - Instruction for multi-hybrid, power supply regeneration type

DATA BOOK IB-1501252 - Specifications of servo drive unit, spindle drive unit, motor, etc.

Manuals for MTBs (Others)

■For M800/M80 Series

■For C80 Series

Manual No. Purpose and Contents

GOT2000 Series User’s Manual

(Hardware) SH-081194 - Outline of hardware such as part names, external dimensions,

installation, wiring, maintenance, etc. of GOTs

GOT2000 Series User’s Manual

(Utility) SH-081195 - Outline of utilities such as screen display setting, operation

method, etc. of GOTs

GOT2000 Series User’s Manual

(Monitor) SH-081196 - Outline of each monitor function of GOTs

GOT2000 Series Connection

Manual (Mitsubishi Electric

Products)

SH-081197 - Outline of connection types and connection method between

GOT and Mitsubishi Electric connection devices

GT Designer3 (GOT2000) Screen

Design Manual SH-081220 - Outline of screen design method using screen creation

software GT Designer3

Manual No. Purpose and Contents

GOT2000/GOT1000 Series CC-Link

Communication Unit User's Manual IB-0800351 - Explanation for handling CC-Link communication unit (for

GOT2000 series/GOT1000 series)

GX Developer Version 8 Operating

Manual (Startup) SH-080372E - Explanation for system configuration, installation, etc. of PLC

development tool GX Developer

GX Developer Version 8 Operating

Manual SH-080373E - Explanation for operations using PLC development tool GX

Developer

GX Converter Version 1 Operating

Manual IB-0800004E - Explanation for operations using data conversion tool GX

Converter

MELSEC-Q CC-Link System Master/

Local Module User’s Manual SH-080394E - Explanation for system configuration, installation, wiring, etc. of

master/local modules for CC-Link system

GOT2000 Series Connection

Manual (Non-Mitsubishi Electric

Products 1)

SH-081198ENG

- Explanation for connection types and connection method

between GOT and other company's devices

GOT2000 Series Connection

Manual (Non-Mitsubishi Electric

Products 2)

SH-081199ENG

GOT2000 Series Connection

Manual (Microcomputers, MODBUS/

Fieldbus Products, Peripherals)

SH-081200ENG

- Explanation for connection types and connection method

between GOT and microcomputers, MODBUS/fieldbus

products, peripherals

GT SoftGOT2000 Version1

Operating Manual SH-081201ENG - Explanation for system configuration, screen configuration and

operation method of monitoring software GT SoftGOT2000

Manual No. Purpose and Contents

MELSEC iQ-R Module Configuration

Manual SH-081262 - Outline of system configuration, specifications, installation,

wiring, maintenance, etc.

MELSEC iQ-R CPU Module User’s

Manual (Startup) SH-081263 - Outline of specifications, procedures before operation,

troubleshooting, etc. for CPU module

MELSEC iQ-R CPU Module User’s

Manual (Application) SH-081264 - Outline of memory, functions, devices, parameters, etc. for

CPU module

QCPU User’s Manual (Hardware

Design, Maintenance and

Inspection)

SH-080483

- Outline of specifications, necessary knowledge to configure

the system and maintenance-related descriptions for Q series

CPU module, etc.

GX Works3 Operating Manual SH-081215 - Outline of functions, programming, etc.

Reference Manual for MTBs

Manual No. Purpose and Contents

M800/M80 Series Smart safety

observation Specification manual BNP-C3072-022

- Explanation for smart safety observation function

C80 Series Smart safety observation

Specification manual BNP-C3077-022

M800/M80 Series CC-Link (Master/

Local) Specification manual BNP-C3072-089 - Explanation for CC-Link

M800/M80 Series Interactive cycle

insertion (Customization)

Specification manual

BNP-C3072-121-

0003 - Explanation for interactive cycle insertion

M800/M80 Series PROFIBUS-DP

Specification manual BNP-C3072-118 - Explanation for PROFIBUS-DP communication function

Precautions for Safety

Always read this manual and enclosed documents before installation, operation, maintenance and inspection to

ensure correct usage. Thoroughly understand the basics, safety information and precautions of the devices before

using.

This manual classifies the safety precautions into "DANGER", "WARNING" and "CAUTION".

Note that the items under " CAUTION" could lead to serious consequences as well depending on the situation.

All the items are important and must always be observed.

The following sings indicate prohibition and compulsory.

The meaning of each pictorial sing is as follows.

DANGER

When the user could be subject to imminent fatalities or serious injuries if handling is mistaken.

WARNING

When the user could be subject to fatalities or serious injuries if handling is mistaken.

CAUTION

When the user could be subject to injuries or the property could be damaged if handling is mistaken.

This sign indicates prohibited behavior (must not do).

For example, indicates "Keep fire away".

This sign indicated a thing that is pompously (must do).

For example, indicates "it must be grounded".

CAUTION

rotated object

CAUTION HOT

Danger

Electric shock risk

Danger

explosive

Prohibited

Disassembly is

prohibited

KEEP FIRE AWAY

General instruction

Earth ground

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Mitsubishi Unità di controllo

Mitsubishi

Mitsubishi QJ72LP25-25 Istruzioni per l’uso

Mitsubishi

Mitsubishi MELSEC System Q Manuale utente

Mitsubishi

Mitsubishi MELSEC-A Manuale utente

Mitsubishi

Mitsubishi FX1N-5DM Manuale utente

Mitsubishi

Mitsubishi Wi-Fi Control Manuale utente

Mitsubishi

Mitsubishi MELSEC-A A1S68AD Manuale utente

Mitsubishi

Mitsubishi MELSEC-A series Manuale utente

Mitsubishi

Mitsubishi Q68TD-G-H01 Manuale utente

Mitsubishi

Mitsubishi Melsec-Q QD63P6-U-HW Manuale utente

Mitsubishi

Mitsubishi AJ71PB92D Manuale utente

Mitsubishi

Mitsubishi QJ71AS92 Istruzioni per l’uso

Mitsubishi

Mitsubishi MELSEC QD75P Manuale utente

Mitsubishi

Mitsubishi MELSEC-A A1SD61 Manuale utente

Mitsubishi

Mitsubishi Melsec-A AJ65SBT Manuale utente

Mitsubishi

Mitsubishi QD75M1 Manuale utente

Mitsubishi

Mitsubishi A6TE2-16SRN Manuale utente

Mitsubishi

Mitsubishi AJ65BT-64DAV Manuale utente

Mitsubishi

Mitsubishi Q62HLC Manuale utente

Mitsubishi

Mitsubishi MELSEC-Q QD77MS Manuale utente

Mitsubishi

Mitsubishi MELSEC A1S64AD Manuale utente

Mitsubishi

Mitsubishi QJ71WS96 Series Manuale utente

Mitsubishi

Mitsubishi MELSEC-F FX2N Series Manuale utente

Mitsubishi

Mitsubishi FX3U-ENET-ADP Manuale utente

Mitsubishi

Mitsubishi MELSEC-Q Q Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente