Mitsubishi MELSEC A1S64AD Manuale utente
A/D Converter module
t
y
pe A1S64AD
User's Manual
(Hardware)
Thank you for buying the Mitsubishi general-purpose programmable
logic controller MELSEC-A Series
Prior to use, please read both this manual and detailed manual
thoroughly and familiarize yourself with the product.
MODEL A1S64AD(H/W)-U-E
MODEL
CODE 13JE46
IB(NA)-66485-D(0609)MEE
©1994 MITSUBISHI ELECTRIC CORPORATION
DANGER
CAUTION
zSAFETY PRECAUTIONS z
(Read these precautions before using.)
When using Mitsubishi equipment, thoroughly read this manual and the
associated manuals introduced in this manual. Also pay careful attention to
safety and handle the module properly.
These precautions apply only to Mitsubishi equipment. Refer to the CPU
module user's manual for a description of the PLC system safety precautions.
These zSAFETY PRECAUTIONSzclassify the safety precautions into two
categories: "DANGER" and "CAUTION".
Procedures which may lead to a dangerous condition
and cause death or serious injury if not carried out
properly.
Procedures which may lead to a dangerous condition
and cause superficial to medium injury, or physical
damage only, if not carried out properly.
Depending on circumstances, procedures indicated by CAUTION may also
be linked to serious results.
In any case, it is important to follow the directions for usage.
Store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
[PRECAUTIONS FOR DESIGN]
CAUTION
zDo not bunch the control wires or communication cables with the main
circuit or power wires, or install them close to each other.
They should be installed 100mm (3.9inch) or more from each other.
Not doing so could result in noise that may cause malfunction.
[INSTALLATION PRECAUTIONS]
CAUTION
zUse the PC in an environment that meets the general specificaitons
contained in this manual. Using this PC in an environment outside the
range of the general specifications could result in electric shock, fire,
erroneous operation, and damage to or deterioration of the product.
zInstall so that the pegs on the bottom of the module fit securely into the
base unit peg holes.
The module fixing screws must be tighten by the specified torque.
Not installing the module correctly or tightening the screws to the terminal
base could result in erroneous operation, damage, or pieces of the product
falling.
[WIRING PRECAUTIONS]
CAUTION
zIf there are high levels of noise, ground the AG terminal and FG terminal with
Class D grounding (Class 3 grounding) or higher dedicated for the PLC.
Failure to observe this could lead to malfunctioning.
zWhen wiring in the PLC, be sure that it is done correctly by checking the product's
rated voltage and the terminal layout. Connecting a power supply that is different
from the rating or incorrectly wiring the product could result in fire or damage.
zTighten terminal screws to the specified torque.
If a terminal screw is not tightened to the specified torque, it the module may fall
out, short circuit, or malfunction.
If a terminal screw is tightened excessively, exceeding the specified torque, the
module may fall out, short circuit, or malfunction due to breakage of the screw or
the module.
zBe careful not to let foreign matters such as sawdust or wire chips get inside the
module. These may cause fires, failure or malfunction.
[STARTUP/MAINTENANCE PRECAUTIONS]
DANGER
zWhen power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
zBefore starting cleaning or terminal screw retightening, always switch off the
power externally in all phases.
Not switching the power off in all phases can cause a module failure or
malfunction.
CAUTION
zNever disassemble or modify the module.
Failure to observe this could lead to trouble, malfunctioning, injuries or fires.
zAlways turn the power OFF before installing or removing the module. Failure to
observe this could lead to module faults or malfunctioning.
zDo not install/remove the terminal block more than 50 times after the first use of
the product. (IEC 61131-2 compliant)
[PRECAUTIONS FOR DISPOSAL]
CAUTION
zDispose of this product as industrial waste.
About the Manuals
The following manuals are related to this product.
Refer to the following table, and procure these manuals as necessary.
Detailed Manual
Manual name Manual No.
(Model code)
A/D converter module type A1S64AD User’s Manual IB-66336
1. Outline
This manual explains the specifications and names of each part of the A1S64AD type
analog/digital converter (hereinafter, A1S64AD) used in combination with the
MELSEC-A Series PLC CPU module (hereinafter PLC CPU).
2. Performance Specifications
The performance specifications of the A1S64AD are shown below.
Item Specifications
Analog input
Voltage: -10 to 0 to +10VDC
(input resistance 1MΩ)
Current: -20 to 0 to +20mA
(input resistance 250Ω)
Select with the input
terminals.
Digital input 16-bit coded binary
-4096 to +4095 when set to 1/4000
-8192 to +8191 when set to 1/8000
-12288 to +12287 when set to 1/12000
Digital output value
(At 5V/20mA gain, 0V/90mA offset)
Analog input
1/4000 1/8000 1/12000
Input/output
characteristics *1
+10V
+5V or +20mA
0V or 0mA
-5V or -20mA
-10V
+4000
+2000
0
-2000
-4000
+8000
+4000
0
-4000
-8000
+12000
+ 6000
0
-6000
-12000
1/4000 1/8000 1/12000
Maximum
resolution Voltage input
Current input
2.5mV
10μA
1.25mV
5μA
0.83mV
3.33μA
General accuracy
*2 Within ±1% ±40 ±80 ±120
Maximum
conversion speed 20ms/channel
Maximum
absolute input Voltage ±15V Current ±30mA
No. of analog
input points 4 channels/module
Specific
isolated area
Isolation
method
Dielectric
withstand
voltage
Insulation
resistance
Between input
terminal and
PLC power
supply
Photocoupler
isolation
500V AC
for
1 minute
5MΩor more
(measured with a
500V DC insulation
resistance tester)
Between
channels Not isolated - -
Isolation
specifications
Item Specifications
No. of occupied
input/output points Special 32 points
Connection
terminal 20-point terminal block
External power
supply Not required
Applicable wire
size 0.75 to 1.5mm2
Applicable crimp
terminal 1.25-3, 1.25-YS3, V1.25-3, V1.25-YS3A
Internal current
consumption
(5VDC)
0.4A
Weight 0.25kg
*1: The gain is set to 5V and the offset to 0V as the default.
*2: This is the accuracy in respect to the maximum digital output value. The maximum
digital value is the maximum value of the selected resolution. It is the same for
either a current input or voltage input.
Point
The range of the analog input at the which maximum resolution and general
accuracy can be tolerated is as follows.
Voltage -10 to 0 to +10V
Current -20 to 0 to +20mA
Refer to the User's Manual for the PLC CPU in use for details on the general
specifications.
3. Names and Settings of Each Part
3.1 Names of each part
The names of each A1S64AD part are shown below.
A1S64AD
1)
3)
4)
2)
5)
RUN
CH
OFFSET
GAIN
TEST
V+
I+
COM
SLD
V+
I+
A.G
FG
COM
SLD
V+
I+
COM
SLD
C
H
1
C
H
2
C
H
3
V+
I+
COM
SLD
C
H
4
1
2
4
6
8
10
12
14
16
18
20
3
5
7
9
11
13
15
17
19
No. Name Details
1) RUN LED
RUN
The operation state of the A1S64AD is indicated.
yNormal mode
ON : In normal operation
Flickering: Write data error has occurred.
OFF : 5V power OFF or watch dog timer error
yTest mode
ON : OFF SET switch or GAIN switch is ON
OFF : OFF SET switch and GAIN switch are
both OFF
2) CHANNEL selection
switch
CH
The channel for adjusting the offset and the gain is
selected.
(Channels other than 1 to 4 have no process.)
3) OFF SET switch
OFF SET
By setting the switch to the OFF SET side, the
analog input value at that time will be saved by the
A1S64AD as the offset value.
4) GAIN switch
GAIN
By setting the switch to the GAIN side, the analog
input value at that time will be saved by the
A1S64AD as the gain value.
5) Test mode terminal
TEST
Short-circuit across terminals 1 and 2 when setting
the offset or gain.
3.2 Setting the offset and gain
Follow the procedure below to change the input/output conversion characteristics.
Start
Short-circuit the test mode terminal
(across 1-2)
Set the "channel selection switch"
to the channel to be changed.
A
Apply the voltage or current to be
set as the offset value.
1)
TEST
RUN
CH
V
V+
COM
I+
V+
COM
A
For voltage
For current
Actually connected resistance value
RUN OFF SET
ON
Set the offset switch to "OFF SET".
OFF
Set to
channel
to be set.
End
Release the test mode terminal
(across 1-2).
Adjust any other
channels?
YES
Apply the voltage or current to be
set as the gain value.
Set the gain switch to "GAIN".
1)
NO
For voltage
For current
V
V+
COM
I+
V+
COM
A
Actually connected resistance value
RUN GAIN
ON
TEST
A
Remarks
The offset value and gain value have the following meanings.
(1) The offset value is the analog input value (voltage or current) at which the digital
output value is "0".
(2) The gain value is the analog input value (voltage or current) at which the digital
output value is the following:
(a) 2000 (1/4000 resolution)
(b) 4000 (1/8000 resolution)
(c) 6000 (1/12000 resolution)
Altri manuali per MELSEC A1S64AD
1
Indice
Altri manuali Mitsubishi Unità di controllo
Mitsubishi
Mitsubishi QJ71WS96 Series Manuale utente
Mitsubishi
Mitsubishi AL-ASI-BD Manuale utente
Mitsubishi
Mitsubishi AJ71PB92D Manuale utente
Mitsubishi
Mitsubishi MELSEC QD75P Manuale utente
Mitsubishi
Mitsubishi L Series Manuale utente
Mitsubishi
Mitsubishi Q Series Manuale utente
Mitsubishi
Mitsubishi FX1N-5DM Manuale utente
Mitsubishi
Mitsubishi MELSEC-A Manuale utente
Mitsubishi
Mitsubishi MELSEC Q Series Manuale utente
Mitsubishi
Mitsubishi Q Series Manuale utente
Mitsubishi
Mitsubishi MELSEC-F FX2N Series Manuale utente
Mitsubishi
Mitsubishi MELSEC Q Series Manuale utente
Mitsubishi
Mitsubishi MELSEC-A A1SJ71AS92 Manuale utente
Mitsubishi
Mitsubishi Q68TD-G-H01 Manuale utente
Mitsubishi
Mitsubishi MELSEC L Series Manuale utente
Mitsubishi
Mitsubishi QD75M1 Manuale utente
Mitsubishi
Mitsubishi MELSEC-A A1SD61 Manuale utente
Mitsubishi
Mitsubishi MELSEC-L Series Manuale utente
Mitsubishi
Mitsubishi AJ65BT-64DAV Manuale utente
Mitsubishi
Mitsubishi AL-ASI-BD Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
