Mitutoyo LGB2 Manuale utente
LINEAR GAGES
SLIM HEAD LGB2
User´s Manual
- Instructions for use -
Read this User's Manual thoroughly before operating the instrument.
After reading, retain it close at hand for future reference.
No.: 4771
④
September 2019
LINEAR GAGES
SLIM HEAD LGB2
User´s Manual
- Instructions for use -
Read this User's Manual thoroughly before operating the instrument.
After reading, retain it close at hand for future reference.
No.: 4771
④
September 2019
No.: 4771
④
PRECAUTIONS
In order to obtain the best possible performance and longest service life from your Linear Gage, please read this
manual thoroughly prior to use. Be sure to observe the following precautions:
•Do not apply excessive force or bump when setting up and operating the Linear Gage.
•The Linear Gage has been accurately adjusted at the factory. Never attempt to disassemble it.
•To ensure measuring accuracy, do not use the Linear Gage in an environment where it may be subjected to
sudden temperature changes.
•When using the Linear Gage in conjunction with other instruments or equipment, an appropriate environment
and operating conditions should be ensured for adequate performance.
•Use the Linear Gage as specified below, otherwise the rated function and performance may not be obtained.
•Have preventative safety measures in place to avoid damage should the Linear Gage malfunction.
NOTICE
All information about our products, in particular the illustrations, drawings, dimensional and performance data as
well as other technical data contained in this publication are approximate average values. The design, technical
data, dimensions and weight are subject to change without notice. Our stated standards, similar technical regu-
lations as well as technical data, descriptions and illustrations of the products correspond to the date of printing.
In addition, our General Terms and Conditions shall apply as amended from time to time. Only the offers made
by us are authoritative.
iNo.: 4771
④
Table of Contents
PRECAUTIONS........................................................................................................... i
1 PART NAMES AND DIMENSIONS........................................................................... 1
2 INSTALLING THE LINEAR GAGE............................................................................2
2.1 CONNECTING THE AIR HOSE (FOR 542-223, 542-230).............................. 2
3 CONNECTING THE COUNTER................................................................................ 4
4 OUTPUT SIGNAL SPECIFICATIONS....................................................................... 5
4.1 All models other than 542-421.........................................................................5
4.2 542-421.............................................................................................................7
5 REPLACING THE CONTACT POINT....................................................................... 8
6 REPLACING THE RUBBER BOOT.......................................................................... 9
7 PROTECTION AGAINST DUST AND WATER.......................................................10
8 SPECIFICATIONS.................................................................................................... 11
ii No.: 4771
④
1 PART NAMES AND DIMENSIONS
1PART NAMES AND DIMENSIONS
①
Contact point
②
Rubber boot
③
Stem
④
Body
⑤
Connecting cable
⑥
Air cylinder
⑦
Air nozzle
⑧
Knurled thimble
⑨
Fixing nut
⑩
Displacement
A Preamplifier box
B Output connector
(HIROSE RM12BPE-6PH)
C Output connector (D-sub)
1No.: 4771
④
2 INSTALLING THE LINEAR GAGE
2INSTALLING THE LINEAR GAGE
Insert the stem into the hole of the gage mount or stand and clamp it with the screw.
See the Linear Gage mount examples given below.
CAUTION
•Do not clamp the Linear Gage using excessive force. This may cause the spindle to stick.
•Do not mount the Linear Gage by clamping with a screw on the stem.
•Do not mount the Linear Gage at any portion other than the stem.
•Mount the Linear Gage perpendicular to the surface to be measured. Otherwise, a measurement error will
be produced as shown below.
Error = I0 - I1
•Ensure that the gage body is not subjected to a force via the pull of the cable.
2.1 CONNECTING THE AIR HOSE (FOR 542-223, 542-230)
Connect the air hose as specified below:
•Air pressure: 0.3-0.4MPa (3-4kgf/cm2)
•Lubrication oil: Class 1 turbine oil (ISO VG32)
①
A
②
Air cylinder
③
Valve
④
Lubricator
⑤
Regulator
⑥
Air filter
⑦
Air regulator set
CAUTION
•Never hold the air cylinder when installing the gage. This may damage portion A. Be sure that portion A
is not subjected to excessive force when connecting the air hose.
2No.: 4771
④
2 INSTALLING THE LINEAR GAGE
NOTICE
The following optional brackets are available to mount the Linear Gage. lf brackets require machining, it is rec-
ommended to set dimension B (See the figures below) to 11.5mm. This Linear Gage has very wide applica-
tions. Use of optional brackets is usually more cost-and time-efficient than fabricating custom designed brack-
ets. Thus, optional brackets have been designed to mount the Linear Gage on varied machines using varied
methods. The brackets are fabricated from cast iron (nickel-plated).
Order No. 303568
Model B-1
AØ9.5 G 16
B 11.5 H 12
C 20 I 1.75
D 30 J 40
E 35 K Ø4.5
F 7
Order No. 303570
Model B-3
AØ9.5 E 40
B 11.5 F 20
C 60 G Ø4.5
D 5.5
Order No. 303572
Model B-5
AØ9.5 F 18
B 11.5 G 15
C 20 H 20
D 30 I Ø4.5
E 35
Order No. 303574
Model B-7
AØ9.5 G 10
B 11.5 H 20
CØ15 I 15
D 20 J 35
E 40 K Ø4.5
F 8.5 L 1.25
3No.: 4771
④
3 CONNECTING THE COUNTER
3CONNECTING THE COUNTER
Couple the connector of the Linear Gage with the INPUT connector on the Linear Gage Counter. (Refer to the op-
eration manual that came with the Linear Gage Counter for further details.)
CAUTION
To avoid malfunction due to electrical interference, do not place the cable of the Linear Gage near the power
cord for other equipment.
NOTICE
The output of the Linear Gage Counter can be used to transfer measurement data from the Linear Gage to a
Mitutoyo Digimatic miniprocessor (data processing unit) for statistical calculations.
4No.: 4771
④
4 OUTPUT SIGNAL SPECIFICATIONS
4OUTPUT SIGNAL
SPECIFICATIONS
4.1 All models other than 542-421
1Output connector: RM12BPE-6PH (Manufacturer: Hirose)
2Connector pin assignment
Pin No. Signal name
*Power supply to the Linear Gage(100mA) The ripple of the
power source should be less than 200mV(p-p).
3Output signal level: +5V (4.8V to 5.3V, 80mA): φA, φA, φB, φB, TTL output (equivalent to line driver SN75158)
4Timing chart
(for LGB2-0105L: 0,1µm)
5Receiving connector and receiver Connector (RM12BRD-6S, Hirose) Receiver (Equivalent to differential input
line receiver SN75182)
6Maximum cable length 20m (using an optional extension cable)
7Basic circuitry for processing received signals. The following diagrams show the basic circuitry for processing
the signals from the Linear Gage, and the waveforms of the output signals.
5No.: 4771
④
4 OUTPUT SIGNAL SPECIFICATIONS
These values determine the
falling/rising pulse width.
Up pulse
Down pulse
6No.: 4771
④
Questo manuale è adatto per i seguenti modelli
14
Indice
Altri manuali Mitutoyo Strumento di misura
Mitutoyo
Mitutoyo LSM-9506 Manuale utente
Mitutoyo
Mitutoyo LGH Series Manuale utente
Mitutoyo
Mitutoyo 500-150-30 Manuale utente
Mitutoyo
Mitutoyo BOREMATIC Manuale utente
Mitutoyo
Mitutoyo 700 Series Manuale utente
Mitutoyo
Mitutoyo ID-SX Manuale utente
Mitutoyo
Mitutoyo LG200 Manuale utente
Mitutoyo
Mitutoyo LGF-110L-B Manuale utente
Mitutoyo
Mitutoyo ID-U Manuale utente
Mitutoyo
Mitutoyo 129 Series Manuale utente
Mitutoyo
Mitutoyo HDM 192 Series Manuale utente
Mitutoyo
Mitutoyo Litematic VL-50A Manuale utente
Mitutoyo
Mitutoyo 500-712-20 Manuale utente
Mitutoyo
Mitutoyo Quickmike MDQ Manuale utente
Mitutoyo
Mitutoyo 7210 Manuale utente
Mitutoyo
Mitutoyo ID-C Manuale utente
Mitutoyo
Mitutoyo SURFTEST SV-3100 Manuale utente
Mitutoyo
Mitutoyo CONTRACER CV-2100 Manuale utente
Mitutoyo
Mitutoyo 209 Series Manuale utente
Mitutoyo
Mitutoyo ID-C X series Manuale di servizio
