molex 207129 Series Manuale utente
Hand Crimp Tool for Claspcon™ Crimp Terminal
Doc No: ATS-011010088 Release Date: 11-29-0 UNCONTROLLED COPY Page 1 of 5
Revision: D Revision Date: 10-30-08
INSULATION
CRIMP
BRUSH
STRIP
LENGTH
BELL MOUTH
CRIMP HEIGHT
BEND
DOWN
BEND UP
ROLLING
CONDUCTOR
CRIMP
TWISTING
Hand Crimp Tool
Speci ication Sheet
Order No. 11-01-0088
Engineering No. HTR4059A
FEATURES
Simple trouble-free full cycle mechanism assures consistent complete terminations
All crimp cavities are fully machined in high carbon steel, then heat treated
SCOPE
Products: Claspcon™ Female Crimp Terminal, 2 -30 AWG.
Terminal Order No. Wire Size Insulation Diameter
Maximum Strip Length Terminal
Series No.
Loose Piece
Reel AWG
mm² mm In. mm In.
02-05-1117
02-05-1119
02-05-1115
02-05-1216
02-05-1217
02-05-1116
02-05-5223
2107
02-05-1118
02-05-5332
2 -30
0.20-0.05
1.78 .070 3.17-3.96
.125-.156
Customer to cut off terminal from reel: 0.20mm (.008”) maximum Cut-off Tab.
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the
scope.
TYPE 3
Hand Crimp Tool for Claspcon™ Crimp Terminal
Doc No: ATS-011010088 Release Date: 11-29-0 UNCONTROLLED COPY Page 2 of 5
Revision: D Revision Date: 10-30-08
CONDITIONS:
After crimping, the conductor profiles should measure the following (see notes on page ).
Solder Speci ication
Conductor Crimp
Wire Size
Width (Re ) Height (Re )
Ψ Pull Force
Minimum Pro ile
Terminal Series No.
AWG mm2 mm In. mm In. N Lb. A B
2 0.20 1.65-1.70 .065-.067 0.6 .025 35.6 8.00 X
26 0.12 1.65-1.70 .065-.067 0.6 .025 26.7 6.00 X
28 0.08 1.65-1.70 .065-.067 0.6 .025 17.8 .00 X
2107
30 0.05 1.65-1.70 .065-.067 0.6 .025 13.3 3.00 X
Notes:
1. Solder crimp heights are supplied for tool calibration only. To
verify tool calibration, insert solder slug (5% tin and 95% lead) into
the crimping profile of the hand tool. Close the hand tool
completely, as if a terminal and wire combination is present.
Measure the solder for crimp height and width. See Figure 1.
Actual crimp heights will vary with every terminal, conductor, and
insulation combinations.
Ψ Pull force should be used as the final criteria for an
acceptable crimp. Pull force is measured with no
influence from the insulation crimp. The insulation
should be stripped long (1/2 in.) so the insulation
grips on the terminal do not grip the wire insulation or
the conductor. Refer to Molex Quality Crimping
Handbook 63800-0029 for additional information on
crimping and crimp testing.
OPERATION
Open the tool by squeezing the handles together, at the
end of the closing stroke, the ratchet mechanism will
release the handles, and the hand tool will spring open.
Crimping Terminals
1. Place the proper terminal into the correct die profile
(A or B), and into the locator block till the terminal
stops. The front of the terminal should sit a little on
the terminal insulation grip guide. See Figure 1.
2. Partially close the tool until the terminal is held in place.
WIRE
TERMINAL
INSULATION
GRIP GUIDE
TERMINAL
LOCATING
BLOCK
Figure 1
TERMINAL
WIDTH
HEIGHT
Figure 1
Hand Crimp Tool for Claspcon™ Crimp Terminal
Doc No: ATS-011010088 Release Date: 11-29-0 UNCONTROLLED COPY Page 3 of 5
Revision: D Revision Date: 10-30-08
3. Place a properly stripped wire into the
terminal and down into insulation grip guide.
See Figure 2.
. Close the tool until the ratchet releases.
5. Carefully lift up on the wire and remove the
crimped terminal.
Note: The tamper proof ratchet action will not
release the tool until it has been fully closed.
Maintenance
It is recommended that each operator of the tool
be made aware of, and responsible for, the
following maintenance steps:
1. Remove dust, moisture, and other
contaminants with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine
oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs
cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight
automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life.
. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
certain terminations may affect the electrical characteristics of an application.
5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,
and store the tool in a clean, dry area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a partially closed position, Do
Not force the handles open or closed. The tool will open easily by lifting the
ratchet release lever (See Figure ).
How to Adjust Tool Crimp Force (See Figure )
It may be necessary over the life of the tool to adjust tool-crimping force. Listed
below are the steps required to adjust the crimping force of the hand tool to
obtain proper crimp conditions:
1. Loosen the stud nut on the back of the handle.
2. With a screwdriver in the slot on the other side of the stud, adjust the force.
Clockwise will increase the force, counter clockwise will decrease the force.
3. Retighten the nut.
. Check the crimp specifications after tool force adjustment.
INSULATION
PUNCH
TERMINAL
TE
RMINAL
LOCATING
BLOCK
Figure 2
WIRE
TERMINAL
INSULATION
GRIP GUIDE
CONDUCTOR
ANVIL
INSULATION
ANVIL
CONDUCTOR
PUNCH
Hand Crimp Tool for Claspcon™ Crimp Terminal
Doc No: ATS-011010088 Release Date: 11-29-0 UNCONTROLLED COPY Page of 5
Revision: D Revision Date: 10-30-08
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Repetitive use of this tool should be avoided.
CAUTIONS:
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
. Use only the Molex terminals specified for crimping with this tool.
Notes:
1. This tool should only be used for the terminals and wire gauges specified on this sheet.
2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above).
Variations in tools, terminals, wire stranding and insulation types may affect crimp height.
3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all
insulation sizes.
. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts
available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.
5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no
influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips
on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping
Handbook 63800-0029 for additional information on crimping and crimp testing.
6. Molex does not certify crimp hand tools.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
Hand Crimp Tool for Claspcon™ Crimp Terminal
Doc No: ATS-011010088 Release Date: 11-29-0 UNCONTROLLED COPY Page 5 of 5
Revision: D Revision Date: 10-30-08
PARTS LIST
Item Number
Order Number
Description Quantity
1 6 000-0073 Repair Kit (Springs, Pins and E-Rings)
1
2 11-11-0156 Terminal Locating Blade 1
3 11-11-0157 Terminal Insulation Grip Guide 1
Americas Headquarters
Lisle, Illinois 60532 U.S.A.
1-800-78MOLEX
Far East North Headquarters
Yamato, Kanagawa, Japan
81- 62-65-232
Far East South Headquarters
Jurong, Singapore
65-6-268-6868
European Headquarters
Munich, Germany
9-89- 13092-0
Corporate Headquarters
2222 Wellington Ct.
Lisle, IL 60532 U.S.A.
630-969- 550
Fax: 630-969-1352
Visit our Web site at http://www.molex.com
1/8” DIA. X .56” LG
ROLL PIN
RATCHET RELEASE LEVER
REPAIR KIT. ALL PARTS
REQUIRED FOR REPAIR.
(ONLY MAIN SPRINGS SHOWN)
1
Figure 4
2
#6
-
32 X 9/16” LG BHCS
3
Altri manuali per 207129 Series
100
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali molex Utensili per crimpatura
molex
molex 207129 Series Manuale utente
molex
molex 63816-0900 Manuale utente
molex
molex RHT-4754 Manuale utente
molex
molex CR5904 Manuale utente
molex
molex 63816-0200 Manuale utente
molex
molex TPX50-50 Guida utente
molex
molex 5050731100 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 63823-4500 Guida utente
molex
molex 63825-5000 Manuale utente
molex
molex 63816-0200 Manuale utente
molex
molex RHT-5771 Manuale utente
molex
molex 63825-2600 Manuale utente
molex
molex CR5907 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex AT-200 Manuale utente
molex
molex 207129 Series Manuale utente
molex
molex 64001-8800 Manuale utente
molex
molex 207129 Series Manuale utente
Manuali Utensili per crimpatura popolari di altre marche
Textron
Textron ESG105L Manuale utente
Tyco Electronics
Tyco Electronics 90035-3 Manuale utente
Emerson
Emerson Klauke ES 20RMCCFB Manuale utente
Continental Refrigerator
Continental Refrigerator PC150HD Manuale utente
TE Connectivity
TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente
Tyco Electronics
Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente