Monoprice 21711 Manuale utente
MONOPRICE
Select Mini 3D Printer V2
P/N 21711
User's Manual
2
CONTENTS
SAFETY WARNINGS AND GUIDELINES.......................................................................................................................................3
INTRODUCTION................................................................................................................................................................................................4
FEATURES..............................................................................................................................................................................................................4
CUSTOMER SERVICE....................................................................................................................................................................................5
PACKAGE CONTENTS.................................................................................................................................................................................5
PRODUCT OVERVIEW.................................................................................................................................................................................6
USING THE MENU SYSTEM....................................................................................................................................................................6
SETUP........................................................................................................................................................................................................................ 7
WI-FI SETUP........................................................................................................................................................................................................11
SOFTWARE INSTALLATION AND SETUP..................................................................................................................................12
Installing Cura for Windows.........................................................................................................................................................12
Repetier-Host............................................................................................................................................................................................18
TECHNICAL SUPPORT..............................................................................................................................................................................20
REGULATORY COMPLIANCE.............................................................................................................................................................20
Notice for FCC .........................................................................................................................................................................................20
Notice for Industry Canada..........................................................................................................................................................20
3
SAFETY WARNINGS AND GUIDELINES
Be careful not to damage the yellow film on the build plate.
Do not remove the insulating tape on the extruder nozzle.
Take care to avoid touching hot parts, including heat blocks, extruder nozzle,
extruded filament, and the heated build plate.
Do not wear gloves when operating or repairing to avoid entanglement.
Keep the printer and all accessories out of reach of children.
Do not remove or disconnect the USB cable when printing from a computer.
Do not pull or twist the black cable at any time.
Do not force or tear anything when during unpacking and setup. This may cause
damage to the printer and/or its accessories.
Do not reach inside the printer during operation.
Always allow the printer and extruded filament to cool before reaching inside.
Ensure that the printer is turned off and unplugged from its power source before
making repairs or performing service.
Do not install this device on an unstable surface where it could fall and cause either
personal injury or damage to the device and/or other equipment.
Do not subject the product to extreme force, shock, or fluctuations in temperature
or humidity.
This device is intended for indoor use only.
Do not expose this device to water or moisture of any kind. Do not place drinks or
other containers with moisture on or near the device. If moisture does get in or on
the device, immediately unplug it from the power outlet and allow it to fully dry
before reapplying power.
Do not touch the device, the power cord, or any other connected cables with wet
hands.
Use only in a well-ventilated area. Do not use in close, confined spaces.
4
Prior to operation, check the unit and power cord for physical damage. Do not use if
physical damage has occurred.
Before plugging the unit into a power outlet, ensure that the outlet provides the
same type and level of power required by the device.
Unplug this device from the power source when not in use.
Take care to prevent damage to the power cord. Do not allow it to become
crimped, pinched, walked on, or become tangled with other cords. Ensure that the
power cord does not present a tripping hazard.
Never unplug the unit by pulling on the power cord. Always grasp the connector
head or adapter body.
INTRODUCTION
Thank you for purchasing this 3D printer from Monoprice! This printer features a single
extruder, which is capable of printing in PLA, ABS, and other materials. You can print from a
Windows® or Mac® PC using a USB connection or can print from 3D model files stored on a
microSD™card, without the need for a PC connection of any kind. This printer is easy to
setup and easy to use following the instructions in this manual.
FEATURES
Single extrusion print head
Can print PLA, ABS, and other materials
Open frame design for ease of use and maintenance
Includes 256MB microSD™card with Cura, Repetier-Host, and a sample 3D model
5
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
1x 3D printer
1x Filament rack
1x Plastic scraper
1x USB cable
1x MicroSD™card
1x Hex wrench
1x Power adapter
1x AC power cord (NEMA 5-15 to IEC 60320 C13)
6
PRODUCT OVERVIEW
1. Feed Mechanism
2. Filament Rack
3. Extruder
4. LCD Display
5. Micro USB and MicroSD Ports
6. Input Power Jack and Power Switch
USING THE MENU SYSTEM
The menu system is displayed on a lighted LCD screen.
The menu selection highlight or pointer is moved by pressing the top and bottom
buttons to the right of the display.
Pressing the top button moves the highlight/pointer to the left and up.
Pressing the bottom button moves the highlight/pointer to the right and down.
Pressing the top button while editing a value decreases that value.
Pressing the bottom button while editing a value increases that value.
Press the center button to activate the selected menu item or to save an edited
value.
7
SETUP
Warning! Take care not to remove or damage the yellow tape on the build platform. This
tape is essential to ensure the 3D model properly adheres to the build platform during
printing. If this tape becomes damaged or wears out, replace it with painter's tape,
Kapton® tape, or ordinary masking tape.
Perform the following steps to prepare the printer for use.
1. Remove the printer from its packaging and place it on
a flat, stable surface with plenty of ventilation and a
nearby AC power outlet.
2. Open the Accessories box and remove the Filament
Rack. Slide the tab at the flat end into the slot on the
left side of the printer frame.
3. Ensure that the power switch on the rear panel is in the OFF position (Oside
depressed). Plug the C13 end of the included AC Power Cable into the C14 panel
connector on the AC Power Adapter, then plug the other end into a nearby AC
power outlet. Depress the Iside of the power switch to power the printer ON.
4. Rotate the control wheel clockwise to move
the highlight to the Move entry, then press the
center of the control wheel to open the Move
menu.
5. Rotate the control wheel clockwise to move
the highlight to the Home Axis entry, then
press the center of the control wheel to activate the Home Axis function. The
printer will move the extruder head to the "home" position.
6. Turn the printer off by depressing the Oside of the power switch.
7. Slide a sheet of A4 paper between the build platform and the extruder nozzle. The
extruder height above the build platform should be 0.05mm, which is the thickness
of a sheet of A4 paper. The extruder is at the correct height when the sheet of
8
paper can be slid between the nozzle and the
platform without binding. When the extruder
head is moved or when the paper is moved
under it, there should be a slight amount of
resistance, but the paper should not be
dragged with the extruder when it is moved.
If the height is incorrect, use the included hex
wrench to make slight adjustments to the
platform height by turning the screws at each
corner of the platform. Turn the screws
clockwise to lower the platform and
counterclockwise to raise the platform. Turn
the wrench no more than 1/4 turn each time,
then recheck the height. Continue checking
and adjusting until the height is correct at all
points on the platform.
8. Insert the included microSD™card into the slot
on the right side of the printer.
9. Turn the printer on by depressing the Iside of
the power switch on the rear panel.
10. Rotate the control wheel clockwise to
highlight the Temperature entry, then press
the control wheel to open the Temperature
menu.
11. Use the control wheel to highlight the Extruder
entry, then press the control wheel to edit the
value. Rotate the control wheel to set the
temperature to the target temperature for the
type of filament you plan on using.
12. Using the same procedure, set the Platform temperature to the target temperature
for your filament type.
9
13. If the button under the Extruder and Platform reads Start Preheat, use the control
wheel to highlight the Start Preheat entry, then press it to start preheating the
extruder and build platform. The button will change to read Stop Preheat and the
Extruder and Platform buttons will read the actual temperatures.
14. While the printer is heating, open your filament. Using a pair of scissors or side
cutters, diagonally snip the end of the filament to make a point, as shown in the
images below.
15. Using the control wheel, navigate to the Move menu, then select the Z Axis option
and press the wheel. Turn the control wheel counterclockwise to raise the extruder
off the build platform.
16. Place the filament reel on the filament rack on
the left side of the printer.
17. While squeezing the lever on the Feed
Mechanism, insert the filament and push it into
opening. Keep pushing until you feel resistance
as it hits the extruder. Release the lever on the
Feed Mechanism.
18. Using the control wheel, highlight the Extruder
entry on the Move menu. Press the control
wheel, then turn it counterclockwise to feed
filament into the extruder. Continue until
filament starts to extrude out of the nozzle.
Wait until filament is no longer coming out of
the nozzle.
10
19. Using the included plastic scraper, clean the extruded filament from the nozzle and
build platform.
20. Using the control wheel, select the Print option
from the main menu. The printer will read the
contents of the microSD™card and display
them on screen. Highlight the cat.gcode file,
then press the control wheel to start printing
the model.
21. After the first layer has been laid down, use
the control wheel to Pause or Cancel the
printing operation. Examine the layer and
compare the printed material with the images
in the table below. If the result is wrong, turn
off the printer and re-adjust the platform
height as indicated. Clean off the printed material using the included plastic scraper,
then print the model print again. Keep repeating this process until the result is
correct.
Wrong
The nozzle is too far from the
platform. This can result in the
extruded material not sticking to the
build platform.
Correct
The nozzle is at the correct height
above the platform.
Indice
Altri manuali Monoprice Stampante 3D
Monoprice
Monoprice 30525 Manuale utente
Monoprice
Monoprice MP Education Guider II Manuale utente
Monoprice
Monoprice Maker Select Plus IIIP Manuale utente
Monoprice
Monoprice MP Voxel Pro Manuale utente
Monoprice
Monoprice 35435 Manuale utente
Monoprice
Monoprice maker architect 13861 Guida alla risoluzione dei problemi
Monoprice
Monoprice 34438 Manuale utente
Monoprice
Monoprice 33820 Manuale utente
Monoprice
Monoprice extrusion i3 13860 Manuale utente
Monoprice
Monoprice 15710 Manuale utente
Monoprice
Monoprice 21824 Manuale utente
Monoprice
Monoprice 43363 Manuale utente
Monoprice
Monoprice cadet Manuale di istruzioni
Monoprice
Monoprice Maker Ultimate 2 Manuale utente
Monoprice
Monoprice Voxel 33820 Manuale utente
Monoprice
Monoprice MP10 Manuale utente
Monoprice
Monoprice MP Delta Pro Manuale utente
Monoprice
Monoprice Select Mini 3D Printer V2 Manuale utente
Monoprice
Monoprice maker architect 13861 Manuale utente
Monoprice
Monoprice MP Voxel Manuale utente
