Mountup MU0027 Manuale utente
MU0027 1.5~8kg
(3.3~17.6lbs)
RATED
Gaming Counterbalance Desk Mount
Instruction Manual
PRODUCT LINE GRAPH
02
WARNING!
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
300mm
75mm
100mm
115mm
75mm
100mm
115mm
189mm 208~281mm 62mm
min10~max85mm
min187~max487mm
min10~max85mm
+90°
-45°
±90°
±90°
±180° ±180°
Components
Hardware
PACKAGE CONTENTS
M4x12mm (x4)
M-A
Screws
M4x16mm (x4)
M-B
Screws
M6x12mm (x4)
M-C
Screws
M6x16mm (x4)
M-D
Screws
D6 (x4)
M-E
Washer
5mm(x4)
M-F
Spacer
03
A (x1)
Arm
C (x1)
Bracket
D (x1)
Clamp
F (x1)
Long Bolt
G (x1)
Grommet Base
I (x1)
Security Screw
H (x1)
Support Plate
J (x6)
Screw
K(x1)
Wingnut
L(x1)
Base
M(x1)
Washer
N(x1)
Calathiform Gasket
O(x1)
Bolt
P(x1)
4mm Allen Key
Q(x1)
5mm Allen Key
E(x1)
Bracket Cover
B (x1)
VESA Plate
R(x1)
6mm Allen Key
STEP 1 Mount the Base to Bottom of the Arm
STEP 2 Clamp Installation OR Grommet Base Installation
04
OPTION A: Clamp Installation
Mount bracket (C) to the bottom of arm (A) using screws(J). Tighten the screws with
supplied 4mm Allen key (P).
p
J
C
A
A
L
M
N
O
Q
Mount the base(L) to the bottom of arm (A) using Washer(M), calathiform gasket(N) and Bolt(O).
Tighten (do not over tighten) the Bolt (O) securely with supplied 5mm Allen key (Q).
concave side of the
washer needs to be
faced to the Base (L)
Secure clamp (D) to upper two holes with
bolts (J) using 4mm Allen Key (P) for desks
with a thickness of 10-55mm.
Secure clamp (D) to lower two holes with
bolts (J) using 4mm Allen Key (P) for desks
with a thickness of 50-85mm.
Adjust the Mount to the Desktop
Thickness 10-55mm
Adjust the Mount to the Desktop
Thickness 50-85mm
Attach bracket cover (E)to bracket(C). Tighten the clamp to the desktop using the plastic knob
or by using 6mm allen key (R).
05
R
OR
C
PJ
10-55mm
50-85mm
D
PJ
D
E
STEP 2 (Continued)
OPTION B: Grommet Base Installation
For grommet hole mounting, place long bolt(F) through the center of grommet base (G).
Mount grommet base to the bottom of arm (A) using screws(J). Tighten the screws with
supplied 4mm Allen key (P).
Run long bolt(F) through grommet hole in desktop. Secure it by using the support plate (H)
and Wingnut (K). Tighten Wingnut.
06
G
J
F
P
K
H
A
F
STEP 3 Attach the monitor to the arm
OPTION A:Flat Back Monitor
Attach the VESA plate (B) to back of monitor and secure with
screws (M-A) or (M-C) with washers (M-E) using 6mm Allen
Key(R). Avoid excessive tightening screws damage the
monitor.
OPTION B:Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-B) or ((M-D) with washers (M-E) and
spacers (M-F) using 6mm Allen Key(R). Avoid
excessive tightening screws damage the monitor.
07
B
M-A
M-C
M-E
R
M-B
M-D
M-E
M-F
R
B
08
Slide the monitor onto the head of swivel arm(A), install the security screw (I). Make
sure the security screw is installed before you rotate the monitor.
If the monitor sags or does not stay, please fasten the tilting bolt on the mount until the
monitor can be held at any angle as needed. Refer to below illustrations to adjust tilting
angle of your monitor.
Refer to below illustrations to
adjust tilting angle of your monitor.
Note: Fasten/loosen the tilting bolt
as needed per arrow direction (+/-)
shown in above diagram.
R
I
A A
09
STEP 4 Adjust the tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension spring in Arm (A) by using 6 mm Allen key (R).
Note:
It is normal for a bit noise when you adjust the spring tension.
R
R
A
After being attached to the arm, the monitor falls down
and can not stay at the desired height by itself.
Turn clockwise(“+”direction) to increase tension
until the monitor can stay at the desired Height by itself.
After being attached to the arm, the monitor rises up and
can not stay at the desired height by itself.
Turn counter-clockwise(“-”direction) to reduce tension until the
monitor can stay at the desired Height by itself.
WARNING
Please DO NOT loosen the screw.
10
STEP 5 Cable Management
Remove the bottom plastic covers from spring arm(A) as shown in diagram.
Run cables from monitor through the bottom of spring arm (A). Reattach plastic covers
as shown in diagram.
A
A
Indice
Altri manuali Mountup Rack e supporto
Mountup
Mountup MU5004 Manuale utente
Mountup
Mountup MU0022 Manuale utente
Mountup
Mountup MU1005 Manuale utente
Mountup
Mountup MU2001 Manuale utente
Mountup
Mountup MU0002 Manuale utente
Mountup
Mountup MU0004 Manuale utente
Mountup
Mountup MU2005 Manuale utente
Mountup
Mountup MU0006 Manuale utente
Mountup
Mountup MU6003 Manuale utente
Mountup
Mountup MU0032 Manuale utente
Mountup
Mountup MU4003 Manuale utente
Mountup
Mountup MU2002 Manuale utente
Mountup
Mountup MU7012 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup MU0060 Manuale utente
Mountup
Mountup MU0023 Manuale utente
Mountup
Mountup MU0006 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup MU9101B Manuale utente
Mountup
Mountup MU6001 Manuale utente
