Mountup MU0004 Manuale utente

Single Monitor Desk Mount

Instruction Manual

If you have any questions , please contact us.

75x75

100x100

2~8kg

4.4~17.6lbs

32"

MU0004

V8.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of

this product, please contact us.

Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or

serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed

weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.

ADULT SUPERVISION IS REQUIRED.

NOTE: Not all hardware included will be used.

DO NOT EXCEED WEIGHT CAPACITY.

WARNING!

PACKAGE CONTENTS

17.6lbs

(8kg)

A (x1)

Upper Arm

B (x1)

Lower Arm

F (x1)

Clamp

I (x1)

Grommet Base

J (x1)

Wingnut

L (x1)

Bolt

K (x1)

Carriage Bolt

N (x1)

3mm Allen Key

O (x1)

4mm Allen Key

P (x1)

6mm Allen Key

G(x5)

M6x10

H(x4)

Pad

C (x1)

Base

M (x1)

Support Plate

M-C (x4)

D6 Washer

M-A (x4)

M4x12

M-B (x4)

M6x12 M-D (x4)

spacer

E (x1)

Bracket

D (x1)

VESA Plate

ASSEMBLY STEPS

STEP 2: Clamp Installation or Grommet Base Installation

STEP 1: Apply Pads to the Base Bottom

OPTION A: Clamp Installation

Mount Bracket (E) to Base Bottom (C) with Bolts (G). Bolts could be tightened by the 4mm Allen Key (O).

Similarly, attach Clamp (F) to Bracket (E) with Bolts (G) and 4mm Allen Key (O).

Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (F) or by Allen key (P).

10-60mm

10-90mm

Apply pads (H) to the base

bottom to avoid desk scratches.

STEP 2: (Continued)

OPTION B: Grommet Base Installation

For grommet hole mounting, place Carriage Bolt (K) through the center of Grommet Base (I).

Mount Grommet Base to Base Bottom (C) with Bolts (G) and tighten by 4mm allen key (O).

Run Carriage Bolt (K) through Grommet Hole on desktop. Attach Support Plate (M) and Wingnut (J).

Last step, tighten Wingnut (J).

10-90mm

Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw

using 3mm Allen key (N).

STEP 3: Arm Installation

Note: Please note that the side with

the label“ ” is installed on the

base(C) when installing the lower

arm(B) to the base (C).

DO NOT tighten the

screw excessively or

it might be stripped.

DO NOT tighten the

screw excessively or

it might be stripped.

STEP 4: Attach Monitor

M-A

M-B

M-C

M-A

M-B

M-C

M-D

OPTION A: Flat Back Monitor

Attach the VESA plate (D) to back of monitor and

secure with screws(M-A)or(M-B) with washers(M-C)

using 6 mm Allen Key (P). Do not tighten the screws

excessively or your monitor might be damaged.

CAUTION:To select the correct screws(M-A or M-B)

for your monitor, you can try to screw it on your

monitor by hand. The one can screw inside is the

correct screw for your monitor.

OPTION B: Curved Back Monitor

Attach the VESA plate (D) to back of monitor and secure

with screws (M-A) or (M-B) with washers (M-C)and

spacers(M-D)using 6 mm Allen Key (P). Do not tighten

the screws excessively or your monitor might be damaged.

Slide the monitor onto the head of swivel arm, install the security bolt (L). Make sure the security

bolt is installed before you rotate the monitor.

STEP 5: Hang Monitor

Refer to below illustrations to adjust tilting angle of your monitor.

Tilts down

Note:

1. Loosen the tilting bolt.

2. Adjust monitor to your

desired tilting angle.

3. Retighten the tilting bolt to

Important Notice:

The gas spring tension is pre-set to the weakest level by default, please hold your monitor

by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.

It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas

spring arm falls down greatly.

STEP 6: Adjust Tension

Note1:

Be sure to keep the arm in horizontal position during adjustment.

Falls down

After being attached to the arm, the monitor fallsdown

and can not stay at the desired height by itself.

Turn counter-clockwise(“+”direction) to increase gas

spring tension until the monitor canstay at the desired

height by itself.

After being attached to the arm, the monitor rises up and

can notstay at the desired heightby itself.

Turn clockwise(“-”direction) to reduce gas spring tension

until the monitor canstay at the desired height by itself.

Rises up

CAUTION

Monitor Weight 2kg 3kg 4kg 5kg 6kg 7kg 8kg

Circles (AT LEAST)

As for how many circles the screw should be turned, the table below is for reference.

Note2:

For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust

tension in upper arm (A) using 6 mm allen key (P).

1 4 8 11 14 17

min

STEP 5: (Continued)

STEP 7: Cable Management

Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram.

Remove bottom plastic covers from gas spring arm as shown in diagram.

Adjust as Desired

DESK DESK

Pay attention while clamp install !

360°

+90°

-45°

180°

Adjust monitor position and rotation.

Altri manuali per MU0004

Indice

Altri manuali Mountup Rack e supporto

Mountup

Mountup MU0033 Manuale utente

Mountup

Mountup MU5004 Manuale utente

Mountup

Mountup MU0021 Manuale utente

Mountup

Mountup MU0022 Manuale utente

Mountup

Mountup MU2005 Manuale utente

Mountup

Mountup MU2001 Manuale utente

Mountup

Mountup MU0004 Manuale utente

Mountup

Mountup MU0014 Manuale utente

Mountup

Mountup MU7012 Manuale utente

Mountup

Mountup MU0002 Manuale utente

Mountup

Mountup MU4002 Manuale utente

Mountup

Mountup MU0032 Manuale utente

Mountup

Mountup MU6001 Manuale utente

Mountup

Mountup PR8001 Manuale utente

Mountup

Mountup MU2001 Manuale utente

Mountup

Mountup MU0005 Manuale utente

Mountup

Mountup MU0045 Manuale utente

Mountup

Mountup MU0029 Manuale utente

Mountup

Mountup MUA6007B Manuale utente

Mountup

Mountup MU5001 Manuale utente

Mountup

Mountup MU0023 Manuale utente

Mountup

Mountup MU0001 Manuale utente

Mountup

Mountup MU0014 Manuale utente

Mountup

Mountup MU0060 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente