Mountup MU0006 Manuale utente
Triple Monitor Counterbalance Desk Mount
Instruction Manual
If you have any questions , please contact us.
MU0006 75x75
100x100
(1~8kg)x3
(2.2~17.6lbs)x3
27"
V9.0
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Beforestarting assembly, verify all parts are included and undamaged. Improperinstallation may cause damage or
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
(2.2~17.6lbs)x3
(1~8kg)x3
A (x1)
Arm
B (x1)
Clamp
All are included in B
Bracket
B1
Clip Plate
B2
Bolts
B5
Bottom Plate
B3
Bolt Y
B4
C (x1)
Decorative cover
G (x1)
Wire clip
K (x1)
Grommet Base
H (x3)
Bolt
I (x3)
Bolt
J (x1)
Support Plate
L(x1)
4mm Allen Key
M(x1)
5mm Allen Key
N(x1)
6mm Allen Key
E(x1)
Middle Head
F(x1)
Pole
D (x3)
VESA Plate
M-E (x12)
D6 Washer
01
M-C (x12)
M6x12 M-F (x12)
M-B (x12)
M4x16
M-D (x12)
M6x16
M-A (x12)
M4x12
Loosen Bolts (B5)by using 6mm Allen Key (N), then lift clip plate (B2), bottom plate (B3), and bolt Y (B4) a little
to release them from bracket (B1).
Attach clip plate(B2), bottom plate(B3), bolt Y(B4), to bracket (B1) using bolts (B5) and 6mm allen key (N).
Mount according to the thickness of desktop.
Mount bracket(B1) to pole(F) using bolts (I). Tighten using 4mm allen key(L).
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
02
35-80mm
NN
10-45mm
F
B1
B5
I
L
B1B1
B3
B4
B3
B4
B5
B5
B2B2
N
OPTION A: Clamp Installation
B4
B
C
N
B1
B2
B3
B4
Decorative cover(C)to pole(F) and secure stand to desktop by tightening clamp (B). Tighten bolt Y (B4) or
by using 6mm allen key (N).
F
OPTION B: Grommet Base Installation
Use 6mm allenkey(N) to detach the bolt(B5), clip plate(B2),bottom plate(B3) and bolt Y(B4) from clamp(B).
STEP 1: (Continued)
03
Install the grommet base plate(K) to the pole (F) using bolt (I).
Install pole(F) with bolt Y(B4) and support plate(J). Tighten bolt Y (B4)or by using 6mm allen key (N).
N
B1
B2
B3
B4
B5
B4
K
B4
10-80mm
I
F
J
N
Install the middle head(E), wire clip(G) and swivel arm(A) to the pole.
Fasten the boltwith supplied 6mm Allen key (N)
STEP 2 : Arm Installation
04
N
G
E
A
Just tighten the bolt, do not
over tighten it in case the
cast aluminum part could
be damaged.
NOTE: Hand tighten screws toavoid over tightening.
STEP 3 : Attach Monitor
05
M-A
M-C
M-E
N
M-B
M-D
M-E
M-F
N
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure
with screws (M-B) or (M-D) with washers (M-E)and
washers(M-F)using 6 mm Allen Key (N). Avoid excessive
tightening screws damage the monitor.
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and
secure with screws(M-A)or(M-C) with washers(M-E)
using 6 mm Allen Key (N). Avoid excessive
tightening screws damage the monitor.
D
D
STEP 4 : Hang Monitor
06
H
Refer to below illustrations to adjust tilting angle of your monitor.
Tilts down
N
Slide the monitors onto the head of swivel arm.Install the security bolt (H). Make sure the security bolt is
installed before you rotate the monitor.
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten the tilting bolt to
Important Notice:
The gas spring tension is pre-set to the weakest level by default, please hold your monitor
by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.
It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas
spring arm falls down greatly.
STEP 5 : Adjust Tension
tension in gas spring arm (A) using 6 mm Allen Key (N).
07
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Falls down
After being attached to the arm, the monitor fallsdown
and can not stay at the desired height by itself.
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor canstay at the desired
height by itself.
After being attached to the arm, the monitor rises up and
can notstay at the desired heightby itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor canstay at the desired height by itself.
Rises up
A
CAUTION
Circles
Monitor Weight
(AT LEAST)
As for how many circles the screw should be turned, the table below is for reference.
Note2:
1kg 2kg 3kg 4kg 5kg 6kg 7kg 8kg
min 1 2 5 7 10 13 15
STEP 6 : Cable Management
Remove bottom plastic covers from gas spring arm (A) .Run cables from monitor through bottom of
gas spring arm (A). Reattach plastic covers as shown in diagram.
08
A
Adjust as Desired
09
M
±180°
±90° ±90°
+35°
-35°
M
N
DESK DESK
Pay attention while clamp install !
Note: The total length of 3 monitors after
arrayed can not be longer than 183cm.
≤183cm
If necessary, refer to above illustrations
to adjust the level of tightness of the
arms.
+
-
M
Altri manuali per MU0006
1
Indice
Altri manuali Mountup Rack e supporto
Mountup
Mountup MU0060 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup MU0032 Manuale utente
Mountup
Mountup MU0024 Manuale utente
Mountup
Mountup MU7012 Manuale utente
Mountup
Mountup MU0011 Manuale utente
Mountup
Mountup MU0011 Manuale utente
Mountup
Mountup MU5004 Manuale utente
Mountup
Mountup MU2005 Manuale utente
Mountup
Mountup MU0022 Manuale utente
Mountup
Mountup MU4003 Manuale utente
Mountup
Mountup MU0014 Manuale utente
Mountup
Mountup MU0002 Manuale utente
Mountup
Mountup MU6002 Manuale utente
Mountup
Mountup MU4002 Manuale utente
Mountup
Mountup MU0045 Manuale utente
Mountup
Mountup MU9101B Manuale utente
Mountup
Mountup MU0033 Manuale utente
Mountup
Mountup MU6001 Manuale utente
Mountup
Mountup MU2001 Manuale utente
