Mountup MU0024 Manuale utente
If you have any questions , please contact us.
MU0024
V3.0
75x75
100x100 32"
(1.5~8kg)x2
(3.3~17.6lbs)x2
Dual Monitor Counterbalance Desk Mount
Instruction Manual
01
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
WARNING!
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY.
C (x1)
Clamp Base Support
D (x1)
Clamp
K (x1)
Wingnut
M (x1)
4mm Allen Key
N (x1)
6mm Allen Key
I(x2)
Security Screw
J(x5)
Bolts
B (x2)
VESA Plate
L (x4 )
Pad
A (x1)
Monitor Stand
E (x1)
Base Support Cover
G (x1)
Base Support
F (x1)
Long Screw
H (x1)
Support Plate
M-E (x8)
D6 Washer
M-C (x8)
M6x12 M-F (x8)
M-B (x8)
M4x16
M-D (x8)
M6x16
M-A (x8)
M4x12
(17.6lbs)x2
(8kg)x2
02
Mount clamp base support (C) to monitor stand (A) with Bolts (J). Bolts could be tightened by the 4mm Allen
Key (M), then Apply pads (L) to the monitor stand (A) bottom to avoid desk scratches.
Attach Clamp (D) to clamp base support (C) with Bolts (J) and 4mm Allen Key (M).
ASSEMBLY STEPS
STEP 1: Choose a mounting option
OPTION A: Clamp Installation
Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (D) or by Allen key (N).
Attach base support cover (E) to clamp base support (C).
L
J
OR
M
N
OR
A
C
10-55mm
D
C
50-85mm
D
EC
M
J
J
M
C
STEP 1: (Continued)
03
OPTION B: Grommet Base Installation
Place long screw (F) through the center of base support (G).
Mount grommet base to monitor stand (A) Bottom with Bolts (J) and tighten by 4mm allen key (M).
Apply pads (L) to the monitor stand (A) bottom to avoid desk scratches.
Run long screw (F) through grommet hole on desktop. Attach support plate (H) and wingnut (K).
Last step, tighten Wingnut (K).
G
A
J
F
M
L
K
H
F
04
STEP 2: Attach the monitors to the arm
M-A
M-C
M-E
N
M-B
M-D
M-E
M-F
N
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-A) or (M-C) with washers (M-E) using 6mm
Allen key(N). Do not tighten the screws excessively
or your monitor might be damaged.
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-B) or ((M-D) with washers (M-E) and
spacers (M-F) using 6mm Allen key(N). Do not tighten
the screws excessively or your monitor might be damaged.
B
B
05
Slide the monitor onto the head of swivel arm, install the security screw (I). Make sure the
security screw is installed before you rotate the monitor.
STEP 3: Hang Monitor
Refer to below illustrations to adjust tilting angle of your monitor.
Tilts down
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten the tilting bolt to
Important Notice:
The gas spring tension is pre-set to the weakest level by default, please hold your monitor
by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.
It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas
spring arm falls down greatly.
I
N
06
STEP 4: Adjust the tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in upper arm using 6 mm allen key (N).
Note1:
Be sure to keep the arm in horizontal position during adjustment.
CAUTION
N
Falls down
After being attached to the arm, the monitor fallsdown
and can not stay at the desired height by itself.
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor canstay at the desired
height by itself.
After being attached to the arm, the monitor rises up and
can notstay at the desired heightby itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor canstay at the desired height by itself.
Rises up
As for how many circles the screw should be turned, the table below is for reference.
Note2:
Monitor Weight 1.5kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST) 108643min 12
07
STEP 5: (Continued)
STEP 5: Cable Management
For both bottom and upper portion of the arm, just slide the cable cover up and away from the arm, do not
need to take much eort to pull the ends of the cable cover away from the arm.
08
STEP 5: (Continued)
STEP 5: (Continued)
On the bottom portion of the arm, insert the cable and slide the cable cover down; On the upper portion of
the arm, insert the cable and press the tabs on the inside of the cable cover slightly inward and slide down
to reattach the cable cover.
1
2
Adjust as Desired
09
DESK DESK
Pay attention while clamp install !
Allen key(M,N) can be stored in Base Support Cover(E) for next time using.
Note:
When tilted, if the monitor sags or does not stay, please fasten the
tilting bolt on the mount until the monitor can be held at any
angle as needed.
N
M
+45°
-45°
180°
360°
360°
270°
Indice
Altri manuali Mountup Rack e supporto
Mountup
Mountup MU0021 Manuale utente
Mountup
Mountup MU4002 Manuale utente
Mountup
Mountup MU1005 Manuale utente
Mountup
Mountup MU0032 Manuale utente
Mountup
Mountup MU2001 Manuale utente
Mountup
Mountup MU0033 Manuale utente
Mountup
Mountup MU2002 Manuale utente
Mountup
Mountup MU0011 Manuale utente
Mountup
Mountup MU0002 Manuale utente
Mountup
Mountup MU5001 Manuale utente
Mountup
Mountup MU0026 Manuale utente
Mountup
Mountup MU0014 Manuale utente
Mountup
Mountup MU0027 Manuale utente
Mountup
Mountup MUA6008B Manuale utente
Mountup
Mountup MU0060 Manuale utente
Mountup
Mountup MU0006 Manuale utente
Mountup
Mountup MU0045 Manuale utente
Mountup
Mountup MU4001 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup MU0004 Manuale utente
