Mountup MU6003 Manuale utente
Height Adjustable Single Monitor Desk Mount
Instruction Manual
75x75
100x100 (2~9kg)
(4.4~19.8lbs)
32"
If you have any questions, please feel free to contact our customer service via Amazon. AHP-21-US1.0
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
(4.4~19.8lbs)
(2~9kg)
A (x1)
Arm
B (x1)
Clamp
All are included in B
Bracket
B1
Clip Plate
B2
Bolt Y
B3
C (x1)
Decorative Cover
F (x1)
Bolt
I(x1)
5mm Allen Key
J(x1)
6mm Allen Key
E(x1)
Base
E1(x3)
Pad
D (x1)
VESA Plate
M-C (x4 )
D5 Washer
01
M-D (x8 )
Spacer H5mm
M-B (x4 )
M4x30mm
M-A (x4 )
M4x12mm
Bolts
B4(x2)
A1 (x1)
Harness Cover
G (x1)
Wire Clip
H(x1)
Fixator
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask
for our help.
Before assembly, please check and make sure all necessary accessories are included and
undamaged. Improper installation, such as use the product for monitors over its load capacity or for
any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for
any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF
REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
ASSEMBLY STEPS
STEP 1: Apply Pads to the Base Bottom
OPTIONA
STEP 2: Clamp Installation Or Grommet Base Installation
02
Fix the Decorative Cover (C) to the Base (E) and fix thebracket on the table by tightening the
Clamp (B).Use a 5mm Allen Wrench (I).
Paste the Pad (E1) onto the Base (E)
E1
E
Loosen Bolts (B4) by using 5mm Allen Key (I),Then align the screw hole on the Base (E), and
then lock the Screw (B4) with a 5mm Allen Wrench (I).
OPTION A: Clamp Installation
I
C
E
Min10mm~Max50mm
B
I
E
Don't over tightened
OPTION B: Grommet Base Installation
STEP 2: (Continued)
03
Use Bolt Y (B3) through the screw hole on Bracket (B1) to fix the Base (E) and the table board
together.
Use 5mm Allen Key(I) to detach Clip Plate(B2)and bolt Y(B3) from Clamp(B).
B4
B1
B2
B3
I
B3
B1
EMin10mm~Max50mm
Install Arm (A),Fixator(H) ,Wire Clip (G) on the base in sequence as shown below.
Make sure to tighten the Fixator(H) to desired place with 5mm Allen Key.
Adjust the tightness of the bolt of Arm(A) to make the rotation flexible.
STEP 3 : Arm Installation
04
G
E
H
A
J
I
NOTE: Hand tighten screws to avoid over tightening.
STEP 4 : Attach Monitor
05
M-A
M-C
I
OPTION B: Curved Back Monitor
Attach the VESA Plate (D) to back of monitor and secure
with Screws (M-B) with Washers (M-C)and
Spacer(M-D)using 5 mm Allen Key (I). Avoid excessive
tightening screws damage the monitor.
OPTION A: Flat Back Monitor
Attach the VESA Plate (D) to back of monitor and
secure with Screws(M-A) with Washers(M-C )
using 5 mm Allen Key (I). Avoid excessive
tightening screws damage the monitor.
D
D
UP
UP
M-B
M-C
M-D
I
one or two piece
STEP 5 : Hang Monitor
06
Refer to below illustrations to
adjust tilting angle of your monitor.
Important Notice:
Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go
suddenly or immediately. Instead, leave the monitor in a slow & gentle way while
observing whether the arms will fall down wildly.
Solution:
1. Loosen the tilting bolt.
2. Hold the bottom of monitor
with one hand and adjust to
determine your desired tilt
angle.
3. Retighten the tilting bolt to
fix the intended angle.
Problem:
If monitor face down
Slide the monitor onto the head of swivel arm.Install the Security Bolt (F).
Make sure the security bolt is tightened before you rotate the monitor.
F
I
STEP 6 : Adjust Tension
07
CAUTION
Note1:
Situation 1: Arm falls down
Solution:
Upper Arm with monitor falls down and fails to stay where
intended.
Turn the inside screw counterclockwise(“+”direction) to increase
gas spring tension until the arm can stay as intended.
Situation 2: Arm rises up
Solution:
Upper Arm with monitor rises up and fails to stay where intended.
Turn the inside screw clockwise(“-”direction) to decrease gas
spring tension until the arm can stay as intended.
J
Be sure to keep the arm in horizontal position during adjustment.
For intended functioning of the mount, you may need to adjust the tension of Arm (A) in
accordance with your monitor weight by 6 mm Allen Key (J).
(AT LEAST) 2 4 6 8 10 12 15
min
For how many circles the screw should be turned, please refer to the table below.
Note2:
STEP 7 : Cable Management
08
I
A1
II
Insert
Tighten
Insert
Press
Press
1.Remove the cable cover using a 5mm Allen Key (I)
2.Fix the wire in the harness wire cover
3.Install and fix the harness cover on the Arm (A) using a 5mm Allen Key (I)
Remove bottom plastic covers from gas spring Arm (A) .Run cables from monitor through bottom
of gas spring Arm (A). Then cover the Wire Cap (A1) onto the upper arm of the Arm (A).
Reattach plastic covers as shown in diagram.
Adjust as Desired
09
DESK DESK
Please do not move stand
outside desk for safety!
±135°
±180°
±90°
±180°
Note: To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of
it with both hands, and rotate vigorously.
If that doesn't work out, please do not hesitate to ask for our help.
Adjust monitor position and rotation.
Swivel
Swivel
Swivel
Tilt
Swivel
Rotation
+90°
-90°
Tilt
Rotation
I
J
Indice
Altri manuali Mountup Rack e supporto
Mountup
Mountup MU0002 Manuale utente
Mountup
Mountup MU0014 Manuale utente
Mountup
Mountup MU2001 Manuale utente
Mountup
Mountup PR8001 Manuale utente
Mountup
Mountup MU4001 Manuale utente
Mountup
Mountup MU0033 Manuale utente
Mountup
Mountup MU0001 Manuale utente
Mountup
Mountup MU4002 Manuale utente
Mountup
Mountup MU0060 Manuale utente
Mountup
Mountup MU2001 Manuale utente
Mountup
Mountup MU0023 Manuale utente
Mountup
Mountup MUA6007B Manuale utente
Mountup
Mountup MU5004 Manuale utente
Mountup
Mountup MU9101B Manuale utente
Mountup
Mountup MU4003 Manuale utente
Mountup
Mountup MU0004 Manuale utente
Mountup
Mountup MU0024 Manuale utente
Mountup
Mountup MU6001 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup MU0011 Manuale utente
