Mountup MU0004 Manuale utente
Single Monitor Counterbalance Desk Mount
Instruction Manual
75x75
100x100
2~8kg
4.4~17.6lbs
32"
MU0004
V6.0
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
17.6lbs
(8kg)
A (x1)
Arm
C (x1)
Bracket
D (x1)
Clamp
F (x1)
Grommet Base
G (x1)
Wingnut
I (x1)
Bolt
H (x1)
Carriage Bolt
J (x1)
Support Plate
K(x1)
4mm Allen Key
L(x1)
5mm Allen Key
M(x1)
6mm Allen Key
E(x5)
M6x10
B (x1)
VESA Plate
M-C (x4)
D6 Washer
M-A (x4)
M4x12
M-B (x4)
M6x12
01
M-D (x4)
spacer
OPTION A: Clamp Installation
Mount bracket (C) to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (K).
Attach clamp (D) to bracket (C) using bolts (E) and 4mm allen key (K). Mount according to thickness of desktop.
Secure stand to desktop by tightening clamp (D) or by using 6mm allen key (M).
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
D
E
KK
E
10-60mm
10-90mm
D
M
OR
OR
02
C C
D
E
K
A
C
OPTION B: Grommet Base Installation
For grommet hole mounting, place carriage bolt (H) through the center of grommet base (F). Mount grommet
base to bottom of gas spring arm (A) using bolts (E). Tighten using 4mm allen key (K). Run carriage bolt (H)
through grommet hole in desktop. Attach metal plate (J) and wingnut (G). Tighten wingnut.
STEP 1: (Continued)
G
H
J
03
K
F
E
H
A
STEP 2: Attach Monitor
B
B
M-A
M-B
M-C
M
04
M-A
M-B
M-C
M-D
M
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to back of monitor and
secure with screws(M-A)or(M-B) with washers(M-C)
using 6 mm Allen Key (M). Avoid excessive
tightening screws damage the monitor.
CAUTION:To select the correct screws(M-A or M-B)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct screw for your monitor.
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-A) or (M-B) with washers (M-C)and
spacers(M-D)using 6 mm Allen Key (M). Avoid excessive
tightening screws damage the monitor.
Slide the monitor onto the head of swivel arm, install the security bolt (I). Make sure the security
bolt is installed before you rotate the monitor.
STEP 3: Hang Monitor
Refer to below illustrations to
adjust tilting angle of your monitor.
05
I
Note: Fasten/loosen the tilting bolt
as needed per arrow direction (+/-)
shown in above diagram.
L
L
STEP 4: Adjust Tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in gas spring arm (A) using 5 mm allen key (L).
06
L
A
If necessary, refer to above illustrations
to adjust the level of tightness of the
arms.
CAUTION
After being attached to the arm, the monitor falls down
and can not stay at the desired height by itself.
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor can stay at the desired
Height by itself.
After being attached to the arm, the monitor rises up and
can not stay at the desired height by itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor can stay at the desired Height by itself.
Note：
Be sure to keep the arm in horizontal
position during adjustment. Or else it
would be dicult to adjust the mount
or damage the mount.
+
-
L
STEP 5: Cable Management
07
A
Remove bottom plastic covers from gas spring arm(A) as shown in diagram.
STEP 5: (Continued)
08
Run cables from monitor through bottom of gas spring arm (A). Reattach plastic covers as shown in diagram.
Adjust as Desired
09
DESK DESK
Pay attention while clamp install !
Note: When tilted, if the monitor sags or does not stay,
please fasten the tilting bolt on the mount until the
monitor can be held at any angle as needed.
360°
360°
360°
+90°
-45°
180°
Altri manuali per MU0004
1
Indice
Altri manuali Mountup Rack e supporto
Mountup
Mountup MU4002 Manuale utente
Mountup
Mountup MU5004 Manuale utente
Mountup
Mountup MU0014 Manuale utente
Mountup
Mountup MU6002 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup PR8001 Manuale utente
Mountup
Mountup MUA6007B Manuale utente
Mountup
Mountup MU0032 Manuale utente
Mountup
Mountup MU0060 Manuale utente
Mountup
Mountup MU4003 Manuale utente
Mountup
Mountup MU0004 Manuale utente
Mountup
Mountup MU0011 Manuale utente
Mountup
Mountup MU0006 Manuale utente
Mountup
Mountup MU0029 Manuale utente
Mountup
Mountup MU0011 Manuale utente
Mountup
Mountup MU2002 Manuale utente
Mountup
Mountup MU0022 Manuale utente
Mountup
Mountup MU0024 Manuale utente
Mountup
Mountup MU0021 Manuale utente
Mountup
Mountup MU9101B Manuale utente
