Moxa Technologies CA-132/132I Manuale utente

CA-132/132I User’s Manual

Third Edition, November 2004

www.moxa.com/product

Moxa Technologies Co., Ltd.

Tel: +886-2-8919-1230

Fax: +886-2-8919-1231

Web: www.moxa.com

MOXA Technical Support

Worldwide: [email protected]

The Americas [email protected]

CA-132/132I User’s Manual

The software described in this manual is furnished under a license agreement and may be used only in accordance

with the terms of that agreement.

Reproduction without permission is prohibited.

Trademarks

MOXA is a registered trademark of The Moxa Group.

All other trademarks or registered marks in this manual belong to their respective manufacturers.

Disclaimer

Information in this document is subject to change without notice and does not represent a commitment on the part of

Moxa.

Moxa provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not

limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to

the products and/or the programs described in this manual, at any time.

Information provided in this manual is intended to be accurate and reliable. However, Moxa Technologies assumes

no responsibility for its use, or for any infringements on the rights of third parties that may result from its use.

This product might include unintentional technical or typographical errors. Changes are periodically made to the

information herein to correct such errors, and these changes are incorporated into new editions of the publication.

Table of Contents

Chapter 1 Introduction ......................................................................................1-1

Overview ............................................................................................... 1-2

Package Checklist................................................................................. 1-2

Product Features................................................................................... 1-2

Product Specifications........................................................................... 1-2

Chapter 2 Hardware Installation.......................................................................2-1

Hardware Installation ............................................................................ 2-2

Block Diagram of CA-132/132I.............................................................. 2-2

RS-422/485 Interface Settings .............................................................. 2-3

I/O Base Address & Interrupt Vector Settings ....................................... 2-3

IRQ Setting............................................................................................ 2-5

Initial Inspection .................................................................................... 2-5

RS-422/485 Pin Assignments ............................................................... 2-6

Chapter 3 Software Installation........................................................................3-1

Windows NT.......................................................................................... 3-2

Windows 2000/XP/2003........................................................................ 3-6

Windows 95/98/ME ............................................................................. 3-16

DOS .................................................................................................... 3-22

Chapter 4 Serial Programming Tool ................................................................4-1

PComm Installation ............................................................................... 4-2

PComm Programming Library............................................................... 4-2

Utilities................................................................................................... 4-2

RS-485 Programming ........................................................................... 4-4

By RTS Mode (For back-compatibility).................................................. 4-4

Appendix A Service Information ........................................................................A-1

MOXA Internet Services........................................................................A-2

Problem Report Form............................................................................A-3

Product Return Procedure.....................................................................A-4

Revision History ....................................................................................A-5

Chapter 1 Introduction

Welcome to MOXA CA-132/132I Series of advanced 2-port RS-422/485 PC/104 communication

modules, a new industrial multiport serial board solution. Both ports of CA-132/132I can be

configured by DIP Switch for either the RS-422 or RS-485 interface, and with its PC/104 standard, the

CA-132/132I Series is compatible with any PC/104 CPU module or CPU card that accepts PC/104

expansion modules.

The following topics are covered in this chapter:

!Overview

!Package Checklist

!Product Features

!Product Specifications

CA-132/132I User’s Manual

1-2

Overview

CA-132/132I is a PC/104 module that supports the RS-422/485 serial interfaces, and can be used with

PC/104 CPU modules or CPU cards that accept PC/104 expansion modules. CA-132/132I has two

independent serial interfaces, which are accessed through RJ45 connectors. You can configure both ports

for the RS-422 or RS-485 interfaces by DIP switch. The module’s industry-standard MOXA UART

(16C550 compatible) is fully programmable. Moxa has implemented its patented ADDC™ technology

for RS-485 automatic direction control, so there is no need to change jumpers to switch the module

between driver and receiver. The built-in 16 KV ESD surge protection protects other devices connected

to the RS-485 network.

Package Checklist

MOXA CA-132/132I products are shipped with the following items:

!1 MOXA CA-132/132I 2-port serial board

!CA-132/132I Document & Software CD

!CA-132/132I Quick Installation Guide

NOTE: Notify your sales representative if any of the above items is missing or damaged.

Product Features

CA-132/132I Series products enjoy the following features:

!2 RS-422/485 ports

!RS-422/485 communication distance up to 4000 feet (1.2 km)

!High speed data transmission rate up to 230.4 Kbps

!Switch selectable for I/O and INT Vector addresses (from Hex 000 to 3FF)

!64-byte FIFOs

!IRQ settings are selectable by jumper

!Built-in 16 KV ESD surge protection for TX and RX lines

!4 LED indicators onboard (red for TX, and green for RX)

!Support 4-wire RS-422 and 2/4-wire RS-485

!ADDC™ for RS-485 transmission

!CA-132I has 2 KV isolation protection

Product Specifications

CA-132/132I Series boards have the following specifications:

!Dimensions: 9.6 cm ×9.0 cm

!Bus: PC/104

!Baud rate: 50 to 230.4 Kbps

!Character length: 5, 6, 7, or 8 bits

!Parity: even, odd, none, mark, and space

!Stop bit: 1, 1.5 or 2

!I/O connectors: dual 8-pin RJ-45 connectors

!Interrupt levels: IRQ 3, 4, 5, 6, 7, 9, 10, 11, 12 or 15

!Clock input: 14.745 MHz

!Power consumption (+5 V): CA-132/210 mA, CA-132I/455 mA

!MTBF: 100,000 hrs @ 25℃environment

!Operating temperature: 0 to 55℃

Introduction

CA-132/132I User’s Manual

1-3

!Storage temperature: -20 to 85℃

!Relative humidity: 5 to 95%, non-condensing

!Regulatory Approvals: FCC Class A, CE

Chapter 2 Hardware Installation

This chapter includes information about hardware installation of CA-132/132I Series boards. The

following topics are covered:

!Hardware Installation

!Block Diagram of CA-132/132I

!RS-422/485 Interface Settings

!I/O Address & Interrupt Vector Settings

!IRQ Setting

!Initial Inspection

!RS-422/485 pin assignments

CA-132/132I User’s Manual

2-2

Hardware Installation

The hardware installation of CA-132/132I serial boards is easy to carry out. Before you insert

CA-132/132I into the PC/104 interface, you must first configure the RS-422/485 setting, I/O Base

Address & Interrupt Vector, and IRQ Settings. Follow the detailed steps given below to install the

CA-132/132I serial board in your computer.

Step 1: Configure the RS-422/485 setting, I/O Base Address & Interrupt Vector, and IRQ Settings

(see details below).

Safety First!

To avoid damaging your system and boards, make sure your PC’s power is turned off before installing

your CA-132/132I board.

Step 2: Turn your PC’s power off, and also shut off the power to any peripheral devices, and remove

the PC’s cover.

Step 3: Insert the CA-132/132I serial board into the PC/104 interface slot.

Step 4: Fasten the holding screw to fix the serial board in place.

Step 5: Replace the PC’s cover.

Step 6: Power on the PC.

Block Diagram of CA-132/132I

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Moxa Technologies Hardware per computer

Moxa Technologies

Moxa Technologies ioLogik E2000 Series Manuale utente

Moxa Technologies

Moxa Technologies RKP-A110 Series Manuale utente

Moxa Technologies

Moxa Technologies THINKCORE W311 Manuale utente

Moxa Technologies

Moxa Technologies C104P Manuale utente

Moxa Technologies

Moxa Technologies C168P Manuale utente

Moxa Technologies

Moxa Technologies MPC-2101 Series Manuale utente

Moxa Technologies

Moxa Technologies UC-8410 Istruzioni per l’uso

Moxa Technologies

Moxa Technologies CP-102N-T Manuale utente

Moxa Technologies

Moxa Technologies W315A Manuale utente

Moxa Technologies

Moxa Technologies CP-118U Series Manuale utente

Moxa Technologies

Moxa Technologies MiiNePort E1-SDK Manuale utente

Moxa Technologies

Moxa Technologies CP-602U-I Manuale utente

Moxa Technologies

Moxa Technologies NPort Server Lite DE-302 Manuale utente

Moxa Technologies

Moxa Technologies CP-118EL Manuale utente

Moxa Technologies

Moxa Technologies Industio C114HI Manuale utente

Moxa Technologies

Moxa Technologies CP-102E Manuale utente

Moxa Technologies

Moxa Technologies MAR-2000 Istruzioni per l’uso

Moxa Technologies

Moxa Technologies CI-104J Manuale utente

Moxa Technologies

Moxa Technologies V2201 Istruzioni per l’uso

Moxa Technologies

Moxa Technologies VPort 66-2MP Series Manuale utente

Moxa Technologies

Moxa Technologies ABC-02-USB-T Manuale utente

Moxa Technologies

Moxa Technologies CP-118U Series Manuale utente

Moxa Technologies

Moxa Technologies CP-102U/UL Manuale utente

Moxa Technologies

Moxa Technologies ABC-02-USB Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente