Moxa Technologies NPort 5130 Manuale utente
P/N: 1802051000014
*1802051000014*
NPort 5100 Series
Quick Installation Guide
Edition 4.2, November 2018
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
Moxa India:
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
2018 Moxa Inc. All rights reserved.
- 2 -
Overview
NPort 5100 series of device servers are compact, palm-sized data
communication devices that allow you to control RS-232 (NPort 5110),
RS-422/485 (NPort 5130), and RS-232/422/485 (NPort 5150) serial
devices over a TCP/IP-based Ethernet.
NOTE
“-T” indicates an extended temperature model.
Package Checklist
Before installing the NPort 5100 series of device servers, verify that the
package contains the following items:
•1 NPort 5100 Series 1-port serial device server
•100 to 240 VAC power adapter (excluding T models)
•4 stick-on pads
•Quick Installation Guide
•Warranty card
Optional Accessories
•DK-35A: DIN-Rail Mounting Kit (35 mm)
NOTE
N
otify your sales representative if any of the above items are
missing or damaged.
NOTE
The operating temperature of the power adapter in the box is
from 0 to 40°C. If your application is out of this range, please
use a power adapter supplied by UL
Listed External Power
Supply (The power output meets SELV and LPS and rated 12
-
48 VDC, minimum current 0.73 A). Moxa has power adapters
with wide temperature range (
-40 to 75°C, -40 to 167°F), the
PWR-12150-(plug type)-SA-T series, for your reference.
- 3 -
Hardware Introduction
As shown in the following figures, NPort 5100 series of device servers
have one male DB9 port for transmitting RS-232 (NPort 5110), RS-
422/485 (NPort 5130), or RS-232/422/485 (NPort 5150) serial data.
NOTE
The NPort 5110, NPort 5130, and NPort 5150 have the same
form factor.
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper clip
or toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, you should release
the reset button.
- 4 -
LED Indicators—NPort 5100’s top panel has three LED indicators,
which are described in the following table.
LED Name
LED Color
LED Function
Ready
Red
Steady on: Power is on and NPort is booting
up.
Blinking: Indicates an IP conflict, or DHCP or
BOOTP server is not responding properly.
Green
Steady on: Power is on and NPort is functioning
normally.
Blinking: The NPort has been located by NPort
Administrator’s Location function
Off
Power is off, or power error condition exists.
Link
Orange
10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Ethernet cable is disconnected, or has a short.
Tx/Rx
Orange
Serial port is receiving data.
Green
Serial port is transmitting data.
Off
No data is being transmitted or received
through the serial port.
Adjustable pull high/low resistor for RS-422/485 (150
KΩ or 1 KΩ)
Jumpers are used to set the pull
high/low resistor values. The default is
150 KΩ. Short the jumpers to set this
value to 1 KΩ. Do not use the KΩ setting
with RS
-232 mode, since doing so will
degrade the RS
-232 signals and shorten
the communicati
on distance.
Hardware Installation Information
STEP 1: After removing the NPort 5100 device server from the box,
connect the NPort 5100 device server to a network. Use a standard
straight-through Ethernet cable to connect to a hub or switch. When
setting up or testing the NPort 5100 device server, you might find it
convenient to connect directly to your computer’s Ethernet port. In this
case, use a cross-over Ethernet cable.
STEP 2: Connect the NPort 5100 device server’s serial port to a serial
device.
STEP 3: Connect the power adaptor.
STEP 4: Placement options
- 5 -
In addition to placing the
NPort 5100
on a desktop or
other horizonta
l surface,
you may also make use of
the DIN
-Rail or Wall Mount
options, as illustrated here.
Wall Mount
DIN-Rail
NOTE
The operating temperature of the power adapter in the box is
from 0 to 40°C. If your application is out of this range, please
use
a power adapter supplied by UL Listed External Power
Supply (The power output meets SELV and LPS and rated 12
-
48 VDC, minimum current 0.73 A). Moxa has power adapters
with wide temperature range (
-40 to 75°C, -40 to 167°F), the
PWR-12150-(plug type)-SA-T series, for your reference.
For the NPort’s configuration, the default IP address of the NPort is:
LAN: Static IP = 192.168.127.254; netmask = 255.255.255.0
You may log in with the password moxa to change any setting to meet
your network topology (e.g., IP address) or serial device (e.g., serial
parameters). If you would like to apply the Real COM mode to your
application, you will need to install the NPort’s driver on your desktop.
You may also refer to Moxa’s support website
https://www.moxa.com/support/ for the user’s manual, driver, NPort
Search Utility, and more.
NOTE
For the NPort with DB Male serial ports, you may refer to the
DB9 Male Ports
Pin Assignment section to loop back pin 2 and
pin 3 for the RS
-232 interface to carry out a self test on the
device.
Pin Assignments
Ethernet Port Pinouts
Pin No.
Ethernet
1
Tx+
2
Tx-
3
Rx+
6
Rx-
- 6 -
NPort 5110—DB9 male (RS-232) port pinouts
Pin No.
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
–
NPort 5130—DB9 male (RS-422/485) port pinouts
Pin No.
RS-422/485-4W
RS-485-2W
1
TXD-(A)
–
2
TXD+(B)
–
3
RXD+(B)
Data+(B)
4
RXD-(A)
Data-(A)
5
GND
GND
6
–
–
7
–
–
8
–
–
9
–
–
NPort 5150—DB9 male (RS-232/422/485) port pinouts
Pin No.
RS-232
RS-422/485-4W
RS-485-2W
1
DCD
TXD-(A)
–
2
RxD
TXD+(B)
–
3
TxD
RXD+(B)
Data+(B)
4
DTR
RXD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
NPort 5110: 128.7 mA @ 12V, 72 mA @ 24V
NPort 5130: 200 mA @ 12V, 106 mA @ 24V
NPort 5150: 200 mA @ 12V, 106 mA @ 24V
Operating Temperature
0 to 55°C (32 to 131°F), for standard models
-40 to 75°C (-40 to 167°F), for -T models
Operating Humidity
5 to 95% RH
Dimensions
75.2 x 80 x 22 mm
(2.96 x 3.15 x 0.87 in)
including ears
52 x 80 x 22 mm
(2.05 x 3.15 x 0.89 in)
without ears
Serial Line Protection
15 KV ESD for serial port
Magnetic Isolation
1.5 KV for Ethernet
Power Line Protection
Level 2 Burst (EFT), EN61000-4-4
Level 2 Surge, EN61000-4-5
Regulatory Approvals
FCC Class A, CE Class A, UL, LVD
- 7 -
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Moxa Technologies Server
Moxa Technologies
Moxa Technologies NPort Server Pro Manuale utente
Moxa Technologies
Moxa Technologies NPort IA5000 Series Manuale utente
Moxa Technologies
Moxa Technologies NPort DE-311 Manuale utente
Moxa Technologies
Moxa Technologies NPort 5210A Manuale utente
Moxa Technologies
Moxa Technologies CN2610 series Manuale utente
Moxa Technologies
Moxa Technologies NPort 5100A Series Manuale utente
Moxa Technologies
Moxa Technologies NPort 6450 Series Manuale utente
Moxa Technologies
Moxa Technologies NPort 6250 Series Manuale utente
Moxa Technologies
Moxa Technologies NPort P5150A-DB9 Manuale utente
Moxa Technologies
Moxa Technologies NPort 5100A Series Manuale utente
Moxa Technologies
Moxa Technologies NPort 5200 Series Manuale utente
Moxa Technologies
Moxa Technologies CN2610 series Manuale utente
Moxa Technologies
Moxa Technologies NPort 5600-8-DT Manuale utente
Moxa Technologies
Moxa Technologies NPort IA5150 series Manuale utente
Moxa Technologies
Moxa Technologies NPort S8455I Manuale utente
Moxa Technologies
Moxa Technologies NPort 5200 Series Manuale utente
Moxa Technologies
Moxa Technologies NPort 5610-8 Manuale utente
Moxa Technologies
Moxa Technologies NPort 5200A Series Manuale utente
Moxa Technologies
Moxa Technologies NPort 5600-8-DT Manuale utente
Moxa Technologies
Moxa Technologies NPort IA5150 series Manuale utente
