Moxa Technologies EtherDevice EDS-405A-PTP Series Manuale

Reproduction without permission is prohibited.

P/N: 1802004050010

EDS-405A-PTP Series Hardware

Installation Guide

Moxa EtherDevice™ Switch

First Edition, July 2014

- 2 -

Overview

The Moxa EtherDevice™ EDS-405A-PTP are 5-port 1588v2 PTP switches

designed especially for real-time control applications. In addition, the

built-in Modbus/TCP, PROFINET RT and EtherNet/IP help automation

engineers to easily maintain an integrated SCADA control network..

Package Checklist

The Moxa EDS-405A-PTP switches are shipped with the following items. If

any of these items is missing or damaged, please contact your customer

service representative for assistance.

•EDS-405A-PTP Ethernet switch

•RJ45-to-DB9 console port cable

•Protective caps for unused ports

•Panel mounting kit (optional—must order separately)

•Hardware installation guide

•CD-ROM with user’s manual and Windows utility

•Warranty card

- 3 -

EDS-405A-PTP Panel Layout (standard)

1. Terminal block for power input

PWR1/PWR2 and relay output

2. System state LED

3. Power input 1 LED

4. Power input 2 LED

5. Fault LED

6. MSTR/HEAD LED

7. CPLR/TAIL LED

8. 10/100BaseT(X) ports

9. Model name

10.

Reset button

11.

Grounding screw

12.

Console port

13.

DIP switches

14.

Power 1, 2/Relay input

15.

Screw hole for wall mounting kit

16.

DIN rail kit

- 4 -

Mounting Dimensions (unit = mm)

Unit = mm (inch)

- 5 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should already be fixed to the

back panel of the EDS-405A-PTP when you take it out of the box. If you

need to reattach the DIN rail attachment plate, make sure the stiff metal

spring is situated towards the top, as shown in the following figures.

STEP 1:

Insert the top of the DIN

rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN

rail attachment unit will

snap into place as shown.

To remove the Moxa EtherDevice switch from the DIN-Rail, simply

reverse Steps 1 and 2.

Wall Mounting (optional)

For some applications, you will find it convenient to mount the

EDS-405A-PTP on the wall, as shown in the following figures.

STEP 1:

Remove the aluminum

DIN

-Rail attachment plate

from

the EDS-405A-PTP’s

rear panel, and then

attach

the wall mount plates

with

M3 screws

, as shown in the

diagram

at the right.

STEP 2:

Mounting

the EDS-405A-PTP on the wall requires 4

screws. Use the

switch, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be

less than 3.5

mm in diameter, as shown in the figure

at the right.

NOTE

Before tightening the screws into the wall, make sure the screw

head and shank size are suitable by inserting the screw into one

of the keyhole-shaped apertures of the wall mounting plates.

Do not screw the screws in completely—leave about 2 mm to allow room

for sliding the wall mount panel between the wall and the screws.

STEP 3: Once the screws are fixed in the wall, insert the four screw heads

through the large parts of the keyhole-shaped apertures, and then slide

the EDS-405A-PTP downwards, as indicated. Tighten the four screws for

added stability.

- 6 -

Wiring Requirements

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

Moxa EtherDevice Switch.

Calculate the maximum possible current in each power wire and

common wire. Observe all electrical codes dictating the

maximum current allowable for each wire

size.

If the current goes above the maximum ratings, the wiring could

overheat, causing serious damage to your equipment.

Be sure to read and follow these important guidelines:

•Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

through the same wire conduit. To avoid interference, wires with

different signal characteristics should be routed separately.

•Use the type of signal transmitted through a wire to determine which

wires should be kept separate. The rule of thumb is that wiring that

shares similar electrical characteristics can be bundled together.

•Keep input wiring and output wiring separate.

•When necessary, you should label the wiring to all devices in the

system.

Grounding the EtherDevice Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface, such as a metal panel.

Wiring the Relay Contact

The Relay Contact consists of the two middle contacts of the terminal

block on the EDS-405A-PTP’s top panel. Refer to the next section for

detailed instructions on how to connect the wires to the terminal block

connector, and how to attach the terminal block connector to the terminal

block receptor.

In this section, we explain the meaning of the two contacts used to

connect the Alarm Contact.

- 7 -

FAULT: The two middle contacts of the

-contact terminal block connector

are used to

detect

user-configured events. The two wires

attached to the fault contacts form an open

circuit when a user

-configured event is

triggered. If a user

configured event does not

occur, the fault circuit remains closed.

Wiring the Redundant Power Inputs

The top two contacts and the bottom two contacts of the 6-contact

terminal block connector on the EDS-405A-PTP’s top panel are used for

the EDS-405A-PTP’s two DC inputs. Top and front views of one of the

terminal block connectors are shown in the following figures:

STEP 1:

Insert the negative/positive DC wires

into the

V-/V+ terminals, respectively.

STEP 2:

To keep the DC wires from pulling

loose, use a small flat

-blade screwdriver to

tighten the wire

-clamp screws on the front of

the terminal block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into t

he terminal block

receptor, which is

located on the

EDS-405A-PTP’s top panel.

ATTENTION

Before connecting

the EDS-405A-PTP to the DC power inputs,

make sure the DC power source voltage is stable.

Communication Connections

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) ports located on the EDS’s front panel are used to

connect to Ethernet-enabled devices.

Next, we show pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also show cable wiring diagrams for

straight-through and cross-over Ethernet cables.

- 8 -

10/100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

Reset Button

The reset button is to reset the Ethernet switch to factory default settings

by pressing and holding the reset button for 5 seconds. Use a pointed

object, such as a straightened paper clip or toothpick, to depress the

reset button. This will cause the STATE LED to blink once a second. After

depressing the button for 5 continuous seconds, the STATE LED will start

to blink rapidly. This indicates that factory default settings have been

loaded and you can release the reset button.

NOTE

DO NOT power off the Ethernet switch when loading default

settings.

Turbo Ring DIP Switch Settings

EDS-405A-PTP series switches are plug-and-play managed redundant

Ethernet switches. The proprietary Turbo Ring protocol was developed by

Moxa to provide better network reliability and faster recovery time. Moxa

Turbo Ring’s recovery time is less than 300 ms (Turbo Ring) or 20 ms

(Turbo Ring V2) —compared to a 3 to 5-minute recovery time for

- 9 -

commercial switches—decreasing the possible loss caused by network

failures in an industrial setting.

There are 4 Hardware DIP Switches for Turbo Ring on the top panel of the

EDS-405A-PTP that can be used to set up the Turbo Ring easily within

seconds. If you do not want to use a hardware DIP switch to set up Turbo

Ring, you can use a web browser, Telnet, or console to disable this

function.

NOTE

Refer to the Turbo Ring DIP Switch section and Using

Communication Redundancy

section in the user’s m

anual for

detail

ed information about the settings and usage of Turbo Ring

and Turbo Ring V2.

EDS-405A-PTP Series DIP Switches

The default setting for each DIP Switch is OFF. The

following table explains the effect of setting the DIP

Switch to the ON position

“Turbo Ring” DIP Switch Settings

DIP 1

DIP 2

DIP 3

DIP 4

Reserved for

future use.

ON: Enable

s this

EDS as

the Ring

Master.

ON: Enables the

default “Ring

Coupling” ports.

ON: Activates

DIP

switches 1, 2,

3 to configure

“Turbo Ring”

settings.

OFF: This EDS

will not be the

Ring Master.

OFF: Do not use

this EDS as the

ring coupler.

OFF: DIP

switches 1, 2, 3

will be disabled.

“Turbo Ring V2” DIP Switch Settings

DIP 1

DIP 2

DIP 3

DIP 4

ON: Enables the

default “Ring

Coupling

(backup)” port.

ON: Enables this

EDS as the Ring

Master.

ON: Enables the

default “Ring

Coupling” port.

ON: Activates

DIP switches 1,

2, 3 to configure

“Turbo Ring V2”

settings.

OFF

: Enables the

default “Ring

Coupling

(primary)” port.

OFF: This EDS

will not be the

Ring Master.

OFF: Do not use

this EDS as a ring

coupler.

OFF: DIP

switches 1, 2, 3

will be disabled.

NOTE

If you do not enable any of the EDS-405A-PTP switches to be the

Ring Master, the Turbo Ring protocol will automatically choose

the

EDS-405A-PTP

with the smallest MAC address range to be the

Ring Master. If you accidentally enable more than one

EDS

-405A-PTP to be the Ring Master, these EDS-405A-PTP

switches will auto

-negotiate to determine which switch

will be the

Ring Master.

- 10 -

NOTE

You must enable the Turbo Ring function first before using the

DIP switch to activate the Master and Coupler functions.

LED Indicators

There are several LEDs on the EDS’s front panel. The function of each LED

is described in the following table.

LED

Color

State

Description

STATE

GREEN

The system passed the

self-diagnosis test on boot-up and

is ready to run.

Blinking

The switch is under reset progress

(1 time/s)

RED On

Blinking

The system self-diagnosis fails on

boot-up.

1. RAM Test Fail / System Info Read

Fail / Switch Init./PTP PHY error Fail

(+ Green MSTR lit on : HW FAIL)

2. FW Checksum Fail / Uncompress

Fail

(+ Green Coupler lit on: SW FAIL)

PWR1 AMBER

Power is being supplied to power

input PWR1.

Off

Power is not being supplied to

power input PWR1.

PWR2 AMBER

Power is being supplied to power

input PWR2.

Off Power is not being supplied to

power input PWR2.

FAULT RED On

1. The signal contact is open.

2. The port being disabled because

of the ingress multicast and

broadcast packets exceed the

ingress rate limit

3. Incorrect loop connection in a

single switch

4. Invalid Ring port connection

MSTR/HEAD GREEN

1. The switch is set as the Master of

the Turbo Ring, or as the Head of

the Turbo Chain.

2. POST H.W. Fail (+Stat on and

Fault blinking)

Blinking

1. The switch has become the Ring

Master of the Turbo Ring

2. The Head of the Turbo Chain,

after the Turbo Ring or the Turbo

Chain is down.

3. The switch is set as Turbo

Chain’s Member and the

corresponding chain port is down.

Off

1. The switch is not the Master of

this Turbo Ring.

This switch is set as a Member of

the Turbo Chain.

Indice

Altri manuali Moxa Technologies Interruttore

Moxa Technologies

Moxa Technologies PT-G510 Series Manuale utente

Moxa Technologies

Moxa Technologies NPort 1220 Manuale utente

Moxa Technologies

Moxa Technologies IKS-6700A series Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-P506A-4PoE Series Manuale utente

Moxa Technologies

Moxa Technologies EDS-G4008 Series Manuale utente

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A Series Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-205 Manuale utente

Moxa Technologies

Moxa Technologies EDS-405A Manuale utente

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A/408A Series Manuale

Moxa Technologies

Moxa Technologies MDS-G4000 Series Manuale utente

Moxa Technologies

Moxa Technologies PT-508 Series Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-510A Series Manuale utente

Moxa Technologies

Moxa Technologies PowerTrans PT-7728-PTP Manuale

Moxa Technologies

Moxa Technologies EtherDevice EDS-P206A-4PoE Series Manuale utente

Moxa Technologies

Moxa Technologies S9450I Series Manuale utente

Moxa Technologies

Moxa Technologies EtherDevice EDS-505A Manuale

Moxa Technologies

Moxa Technologies TN-5308 Manuale utente

Moxa Technologies

Moxa Technologies EDS-600 Series Manuale

Moxa Technologies

Moxa Technologies TN-5510A Series Manuale utente

Moxa Technologies

Moxa Technologies ToughNet TN-5510-2GLSX-ODC Manuale

Moxa Technologies

Moxa Technologies EDS-510E Series Manuale utente

Moxa Technologies

Moxa Technologies PowerTransPT-7728-PTP Manuale utente

Moxa Technologies

Moxa Technologies PT-510 Series Manuale

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente