Multicomp pro MP780649 Manuale utente

Function Range

inH2O 138.3

osi 5.000

mbar 344.7

kPa 34.47

inHg 10.18

mmHg 258.5

Resolution

0.1

0.001

0.1

0.01

0.001

0.1

Function Range Resolution

ozin280.00 0.01

ftH2O 11.53 0.01

cmH2O 351.5 0.1

kgcm2 0.351 0.001

bar 0.344 0.001

Software (Disk & PC cable).

Manometer

MP780649

1.lntroduction

The device measures Gauge/Differential Pressure from O to 5 psi, it features

11 selectable units of measure: inH2O, psi, bar, mbar, kPa, inHg, mmHg, ozin2,

ftH2O, cmH2O, kgcm2.

Additional features include Data Hold. Auto Power Off disabled, and a USB

connector for capturing readings to a PC using optional software.

Careful use of this meter will provide years of reliable service.

2.Specifications

Dual LCD

±0.3%FSO (25°C)

±0.2% (Max.±0.5% FSO)

±0.29% FSO

±5 psi

20psi

0.5 Seconds typical

Yes

Err.1

Err.2

0 to 50°C

-10 to 60°C

1 x 9V Battery or external 9VDC

Display

Accuracy

Repeatability

Linearity/Hysteresis

Pressure Range

Maximum Pressure

Response Time

Low Battery Indicator

Over range Indicator

Under range Indicator

Operating Conditions

Storage Conditions

Power Supply



.

3.Buttons

The meter has six buttons

UNITS

DIF

REC

HOLD

BACKLIGHT

0N/OFF

4.Display Description

1- Hold Function

2- Differential Mode

3- Primary Data screen

4- Record Mode

5- MAXIMIN/AVG

6- Low Battery indicator

7- Pressure Unit indicator

8- Relative time clock

9- Data output USB socket

LDATALOGGER-- 9



4�C

H/M/S

S MIN AVG 8

6 

 

5.0peration

5-1. Power

Press the ON/OFF button to turn power on or off. The meter will perform a short

self-test when turned on. The meter defaults to the setting used during the last

operation.

5-2. Zero Adjust and Offset

Before use and without fittings attached to the meter, press the HOLD button

for more than 2 seconds to zero the meter. The meter will reset and display "o

o oo" from right to left then 0.000 will be displayed.

If it is desired to offset the meter and display, press the DIF button while taking

a measurement. Subsequent reading will be the difference between the

current measurement and the measurement that was on the display before the

DIF button was pressed.

5-3. Data Hold

Press the HOLD button momentarily to freeze the displayed reading. The

'HOLD' icon will appear on the upper left-hand side of the display. If the

pressure value is over the range, error codes will show on the screen. Press

the HOLD button again to return to normal operation.

5-4. Record

The MAX/MIN mode allows the user to view only the highest (MAX), lowest

(MIN) or average (AVG) readings with relative time stamp.

Press the REG button once and REG appears on the display (all other

functions are locked out except for Power & Backlight). The relative time clock

also appears in the secondary display and starts counting.

Press the REG Button again and MAX appears on the display .The display is

now showing the maximum pressure and relative time that it was recorded.

Press the REG button to display the minimum MIN reading with the relative

time.

Press the REG button to display the average value AVG reading with the

relative time.

Press the REC button again to continue recording MAX/MIN /AVG

measurements.

To exit the MIN/MAX/AVG mode, press the REC button for 3 seconds to

return to normal operation.



.

5-5. Backlight Display

Press the Backlight button to turn on the backlight.

It will remain on for 40 seconds.

5-6. Automatic Power Off

The meter will automatically shut off after 20 minutes to conserve battery life.

To disable Auto Power Off , hold down the HOLD button and turn on the meter on,

An "n" will appear in the display indicating that Auto Power Off mode is disabled.

The meter will return to normal operation when it is turned off.

5-7. Units

Press the Unit button momentarily and the meter will cycle through the 11 available

units of measure as indicated by the cursor on the bottom of the display.

USB

To collect readings to a PC using included software.

6. Error Codes

An error message will appear on the display if the meter fails an internal diagnostic

test. And it will freeze all the buttons.

•Err.1: Pressure value is over the range.

•Err.2: Pressure value is below the range.

•Err.3: DIF function, the differential pressure value is over range.

•Err4: DIF function, the differential pressure value is below range.

7. Battery Replacement

When the battery power falls low "BAT" will appear on the LCD.

Replace the 9V battery noting polarity.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS

OF ELECTRICAL & ELECTRONIC EQUIPMENT

These symbols indicate that separate collection of Waste Electrical and Electronic

Equipment (WEEE) or waste batteries is required. Do not dispose of these items with

general household waste. Separate for the treatment, recovery and recycling of the

materials used. Waste batteries can be returned to any waste battery recycling point

which are provided by most battery retailers. Contact your local authority for details of

the battery and WEEE recycling schemes available in your area

Made in China. LS12 2QQ

Man Rev 1.0

Altri manuali multicomp pro Strumento di misura

multicomp pro

multicomp pro MP700852 Manuale utente

multicomp pro

multicomp pro MP780647 Manuale utente

multicomp pro

multicomp pro MP005768 Manuale utente

multicomp pro

multicomp pro MP780904 Manuale utente

multicomp pro

multicomp pro MP780994 Manuale utente

multicomp pro

multicomp pro MP700506 Manuale utente

multicomp pro

multicomp pro MP780905 Manuale utente

multicomp pro

multicomp pro MP60607 Manuale utente

multicomp pro

multicomp pro MP001186 Manuale utente

multicomp pro

multicomp pro MP700022 Manuale utente

multicomp pro

multicomp pro MP770291 Manuale utente

multicomp pro

multicomp pro MP760607 Manuale utente

multicomp pro

multicomp pro MP700006 Manuale utente

multicomp pro

multicomp pro MP780892 Manuale utente

multicomp pro

multicomp pro MP780118 Manuale utente

multicomp pro

multicomp pro MP760861 Manuale utente

multicomp pro

multicomp pro MP780896 Manuale utente

multicomp pro

multicomp pro MP780966 Manuale utente

multicomp pro

multicomp pro MP780522 Manuale utente

multicomp pro

multicomp pro MP700121 Manuale utente

multicomp pro

multicomp pro MP780859 Manuale utente

multicomp pro

multicomp pro MP780002 Manuale utente

multicomp pro

multicomp pro MP760862 Manuale utente

multicomp pro

multicomp pro MP780117 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente

multicomp pro MP780649 Manuale utente

Manuali Strumento di misura popolari di altre marche