National Instruments Isolated Analog Output Module SCC-AO10 Manuale utente

USER GUIDE

SCC-AO10 Isolated Analog

Output Module

The SCC-AO10 is an isolated voltage output module with an output range

of ±10 V. The output voltage level is controlled by the DAC output of an

E Series DAQ device. You can increase the output voltage level to ±20 V

by connecting two SCC-AO10 modules in series.

Conventions

The following conventions are used in this guide:

»The »symbol leads you through nested menu items and dialog box options

to a final action. The sequence File»Page Setup»Options directs you to

pull down the File menu, select the Page Setup item, and select Options

from the last dialog box.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to

avoid injury, data loss, or a system crash. When this symbol is marked on

the product, refer to the Read Me First: Safety and Radio-Frequency

Interference document, shipped with the product, for precautions to take.

When symbol is marked on a product it denotes a warning advising you to

take precautions to avoid electrical shock.

When symbol is marked on a product it denotes a component that may be

hot. Touching this component may result in bodily injury.

bold Bold text denotes items that you must select or click in the software, such

as menu items and dialog box options. Bold text also denotes parameter

names.

SCC-AO10 Isolated Analog Output Module User Guide 2 ni.com

italic Italic text denotes variables, emphasis, a cross reference, an introduction

to a key concept, or text as it appears on a hardware label. This font also

denotes text that is a placeholder for a word or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the

keyboard, sections of code, programming examples, and syntax examples.

This font is also used for the proper names of disk drives, paths, directories,

programs, subprograms, subroutines, device names, functions, operations,

variables, filenames, and extensions.

SC-2345 SC-2345 refers to both the SC-2345 connector block and the SC-2345 with

configurable connectors.

SCC SCC refers to any SCC Series signal conditioning module.

©National Instruments Corporation 3 SCC-AO10 Isolated Analog Output Module User Guide

What You Need to Get Started

To set up and use the SCC-AO10, you need the following items:

❑SC-2345/2350 with one of the following:

– SCC-PWR01

– SCC-PWR02 and PS01 power supply

– SCC-PWR03 (requires a 7 to 42 VDC power supply, not included)

❑One or two SCC-AO10 modules

❑SC-2345/2350 User Manual, available at ni.com

❑SCC-AO10 Isolated Analog Output Module User Guide

❑SCC Quick Start Guide, available at ni.com

❑Read Me First: Safety and Radio-Frequency Interference

❑SC-2345 Quick Reference Label

❑68-pin E Series DAQ device, documentation, and 68-pin cable of less

than 1.5 m length

❑1/8 in. flathead screwdriver

❑Numbers 1 and 2 Phillips screwdrivers

❑Wire insulation strippers

❑NI-DAQ (current version) for Windows 2000/NT/XP/Me

Note Software scaling of measurements is not supported on the Macintosh operating

system.

SCC-AO10 Isolated Analog Output Module User Guide 4 ni.com

Device Specific Information

Note For general SCC module installation and signal connection information, and

information about the SC-2350 carrier, refer to the SCC Quick Start Guide, available

for download at ni.com/manuals.

Installing the SCC-AO10

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document

before removing equipment covers or connecting/disconnecting any signal wires.

Plug the SCC-AO10 into either SC-2345 analog output socket J(X+17),

where Xis 0 or 1. The SC-2345 routes the voltage output of E Series DAQ

device analog output channel AO (X) to the SCC-AO10.

Connecting the SCC-AO10 to a Load

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document

before removing equipment covers or connecting/disconnecting any signal wires.

Note The signal names have changed. Refer to ni.com/info and enter rdtntg to

confirm the signal names.

The SCC-AO10 has a three-pin screw-terminal connector that accepts

28–16 AWG wires.

The screw terminals are labeled by pin numbers 1 to 3. Pin 1 is the isolated

ground. Pins 2 and 3 both connect to the isolated voltage output for

flexibility in field wiring.

Caution Connecting an external voltage source to the output terminals of the SCC-AO10

may damage the module.

Figures 1 and 2 show the SCC-AO10 connected to a nonreferenced load

and to a load with a high common-mode voltage.

©National Instruments Corporation 5 SCC-AO10 Isolated Analog Output Module User Guide

Figure 1. SCC-AO10 Connected to a Nonreferenced Load

Figure 2. SCC-AO10 Connected to a Load with a High Common-Mode Voltage

Connecting Two SCC-AO10 Modules in Series

You can increase the maximum total output voltage to ±20 V by connecting

two SCC-AO10 modules in series. Plug the two modules into sockets J17

and J18 of the SC-2345, and wire the modules to a load as shown in

Figure 3.

AO GND

SCC-AO10

E Series

DAQ Device

AO (

)

Load

AO GND

SCC-AO10

E Series

DAQ Device

AO (

)

Load

SCC-AO10 Isolated Analog Output Module User Guide 6 ni.com

Figure 3. Connecting Two SCC-AO10 Modules in Series

The SC-2345 routes the E Series DAQ device analog output channels

AO 0 and AO 1 to the SCC-AO10 modules, and the resulting maximum

output voltage range is ±20 V. Refer to Figure 3 and use the following

formula to calculate the total output voltage from both SCC-AO10

modules:

VOutTotal =VOUT1 +VOUT2

where

VOutTotal is the total output voltage from both SCC-AO10 modules

VOUT1 is the voltage across terminals 1 and 3 of the SCC-AO10

module in socket J17

VOUT2 is the voltage across terminals 1 and 3 of the SCC-AO10

module in socket J18

For information about how to configure the SCC-AO10 module with

NI-DAQmx, refer to the SCC Quick Start Guide.

SCC-AO10 in Socket J18

SCC-AO10 in Socket J17

Load

AO GND

E Series

DAQ Device

AO 0

AO GND

AO 1

VOUT2

VOUT1

–

VOutTotal

–

©National Instruments Corporation 7 SCC-AO10 Isolated Analog Output Module User Guide

Using the SCC-AO10

Scaling Voltage Measurements

The SCC-AO10 is a ±10 V isolated analog output module. The output

voltage is controlled by an E Series DAQ device AO output channel,

AO (X). The relationship between the AO (X) voltage level and the output

voltage level of the SCC-AO10 is a one-to-one linear relationship. That is,

VAO (X) =VAO10

where

VAO (X)is the AO 0 voltage level

VAO10 is the SCC-AO10 voltage output in volts

Isolated Ground Reference

Each SCC-AO10 module is referenced to its own isolated ground. Each

isolated ground can have up to 300 V of common-mode voltage between

itself and any other channel ground or chassis ground. Refer to the

Connecting the SCC-AO10 to a Load section for ways to use the isolated

ground in signal connections.

Calibrating Gain and Offset Errors

The SCC-AO10 is calibrated at the factory before shipment. To adjust the

gain and offset of the SCC-AO10 in your system using an E Series DAQ

device, you need a voltage meter and a 1/8 in. flathead screwdriver. Before

adjusting the SCC-AO10, allow 30 minutes for the DAQ device to warm

up to its nominal operating temperature.

To adjust the gain and offset of the SCC-AO10, complete the following

steps:

1. Disconnect the load from the SCC-AO10 you want to calibrate.

2. Set an output range of –10 to +10 V for AO (X), the E Series DAQ

device channel connected to the SCC-AO10.

3. Connect the negative lead of the voltmeter to the isolated ground

terminal (pin 1) and the positive lead to the voltage output terminal

(pin 2 or 3) of the SCC-AO10.

4. Using your software, set AO (X) to output 0 VDC.

5. Adjust the offset potentiometer on the top of the SCC-AO10 until the

voltmeter reads 0 VDC ±100 µV. The offset is now calibrated.

6. Using your software, have AO (X) output 9.9 VDC.

SCC-AO10 Isolated Analog Output Module User Guide 8 ni.com

Adjust the gain potentiometer on the top of the SCC-AO10 until the

voltmeter reads 9.9 VDC. The gain is now calibrated.

Specifications

These ratings are typical at 25 °C unless otherwise stated.

Electrical

Number of output channels.....................One nonreferenced (floating)

Input range ..............................................±10 V

Output range ...........................................±10 V

Current drive...........................................±30 mA

Gain nonlinearity ....................................0.5% of full-scale output range

Output noise............................................2.5 mVrms typ; 4 mVrms max

Bandwidth...............................................>23 kHz

Slew rate .................................................1 V/µs

Short circuit protection

Current.............................................37 mA max

Duration...........................................Unlimited

Load impedance......................................10,000 pF max

Power Requirement

Analog power .........................................180 mW max at full load

172 mW max with no load

+15 V ...............................................6 mA max at full load

5.73 mA max with no load

–15 V ...............................................6 mA max at full load

5.73 mA max with no load

Digital power (+5 V) ..............................1.15 W max at full load

600 mW max with no load

+5 V .................................................230 mA max

120 mA max with no load

©National Instruments Corporation 9 SCC-AO10 Isolated Analog Output Module User Guide

Physical

Dimensions............................................. 8.89 cm × 2.92 cm ×1.85 cm

(3.50 in. ×1.15 in. ×0.73 in.)

Mass ....................................................... 37 g

I/O connectors ........................................ One 20-pin right-angle male

connector; one 3-pin screw

terminal

Field-wiring diameter............................. 28 to 16 AWG

Maximum Working Voltage

Maximum working voltage refers to the output signal voltage plus the

common-mode voltage.

Module to earth ...................................... ±300 V, Installation Category II

Environmental

Operating temperature............................ 0 to 50 °C

Storage temperature ............................... –20 to 70 °C

Humidity ................................................ 10 to 90% RH, noncondensing

Maximum altitude .................................. 2,000 m

Pollution Degree (indoor use only) ........ 2

Stability

Recommended warm-up time ................ 10 min (30 min for connected

E Series DAQ device)

Output offset drift................................... 300 µV/°C

Gain temperature coefficient.................. 300 ppm/°C

SCC-AO10 Isolated Analog Output Module User Guide 10 ni.com

Safety

This product is designed to meet the requirements of the following

standards of safety for electrical equipment for measurement, control,

and laboratory use:

• IEC 61010-1, EN 61010-1

• UL 3111-1, UL 61010B-1

• CAN/CSA C22.2 No. 1010.1

Note For UL and other safety certifications, refer to the product label, or visit

ni.com/hardref.nsf, search by model number or product line, and click the

appropriate link in the Certification column.

Electromagnetic Compatibility

Emissions................................................EN 55011 Class A at 10 m

FCC Part 15A above 1 GHz

Immunity ................................................EN 61326:1997 + A2:2001,

Table 1

CE, C-Tick, and FCC Part 15 (Class A) Compliant

Note For EMC compliance, operate this device with shielded cabling.

CE Compliance

This product meets the essential requirements of applicable European

directives, as amended for CE marking, as follows:

Low-Voltage Directive (safety)..............73/23/EEC

Electromagnetic Compatibility

Directive (EMC) .....................................89/336/EEC

Note Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit

ni.com/hardref.nsf, search by model number or product line, and click the

appropriate link in the Certification column.

Altri manuali per Isolated Analog Output Module SCC-AO10

Indice

Altri manuali National Instruments Unità di controllo

National Instruments

National Instruments PXIe-4357 Manuale

National Instruments

National Instruments NI 9226 Manuale utente

National Instruments

National Instruments NI FlexRIO PXI-7952R Manuale utente

National Instruments

National Instruments NI 9262 Manuale utente

National Instruments

National Instruments NI 9852 Manuale utente

National Instruments

National Instruments NI 9247 Manuale utente

National Instruments

National Instruments NI R Series Manuale utente

National Instruments

National Instruments PXIe-8821 Manuale utente

National Instruments

National Instruments FP-CTR-500 Manuale utente

National Instruments

National Instruments SCXI -1122 Manuale

National Instruments

National Instruments Module SCXI-1503 Manuale

National Instruments

National Instruments NI 9246 Manuale utente

National Instruments

National Instruments 9238 Manuale per l'uso e la cura

National Instruments

National Instruments PXIe-7902 Manuale utente

National Instruments

National Instruments SLSC-12101 Manuale utente

National Instruments

National Instruments NI 9930 Manuale utente

National Instruments

National Instruments NI 9401 Manuale utente

National Instruments

National Instruments SCXI-1521 Manuale utente

National Instruments

National Instruments NI 9861 Manuale utente

National Instruments

National Instruments SCC-LP Series Manuale utente

National Instruments

National Instruments NI 9411 Manuale utente

National Instruments

National Instruments NI 9214 Manuale utente

National Instruments

National Instruments FBUS-HSE/H1 LD Manuale utente

National Instruments

National Instruments NI PCIe-1430 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente