National Instruments PXIe-4466 Manuale utente
PXIe-4466/4467/4468
Getting
Started Guide
2023-03-28
Getting Started Guide
This document explains how to install, configure, and set up the PXIe-446x Sound
and Vibration Module.
Note In this document, the PXIe-4466, PXIe-4467, and PXIe-4468 are
referred to inclusively as the PXIe-446x.
Driver support for the modules was first available in the following NI-DAQmx
versions:
■PXIe-4466—NI-DAQmx 20.7
■PXIe-4467—NI-DAQmx 21.3
■PXIe-4468—NI-DAQmx 22.8
For the list of devices supported by a specific release, refer to the NI-DAQmx
Readme, available on the version-specific download page.
Note Before you begin, install and configure your chassis and controller.
Unpacking the Kit
The PXIe-446x ships in an antistatic package to prevent electrostatic discharge from
damaging device components. To prevent such damage when handling the device,
ground yourself using a grounding strap or by holding a grounded object, such as
your computer chassis, and complete the following steps.
1. Touch the antistatic package to a metal part of the computer chassis.
2. Remove the module from the package and inspect it for loose components or
other signs of damage.
Notice Never touch the exposed pins of connectors.
© National Instruments 3
PXIe-4466/4467/4468 Getting Started Guide
Note Do not install a module if it appears damaged in any way.
3. Unpack any other items and documentation from the kit.
Store the module in the antistatic package when the module is not in use.
Verify the Kit Contents
The following items are necessary to set up and use the PXIe-446x.
■ PXIe-446x analog input/output module
■Module Safety, Environmental, and Regulatory Information document
Other Equipment
The following additional items, not included in the module kit, are necessary to
operate the PXIe-446x.
■PXI Express chassis with
■controller, or
■MXI-Express (card or built-in)
■(optional) LabVIEW
Note For the list of LabVIEW versions supported by a specific version
of NI-DAQmx, refer to the NI-DAQmx Readme, available on the version-
specific download page at ni.com/downloads.
Preparing the Environment
Refer to the module Safety, Environmental, and Regulatory Information
document shipped with your device for the environmental specifications required
for the PXIe-446x.
ni.com
4
PXIe-4466/4467/4468 Getting Started Guide
Note This model is intended for use in indoor applications only.
Installing the Software
You must be an Administrator to install NI soware on your computer.
1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.
2. Download the NI-DAQmx driver soware installer from ni.com/downloads.
NI Package Manager downloads with the driver soware to handle the
installation. Refer to the NI Package Manager Manual for more information
about installing, removing, and upgrading NI soware using NI Package
Manager.
Driver support for the modules was first available in the following NI-DAQmx
versions:
■PXIe-4466—NI-DAQmx 20.7
■PXIe-4467—NI-DAQmx 21.3
■PXIe-4468—NI-DAQmx 22.8
3. Follow the instructions in the installation prompts.
Note Windows users may see access and security messages during
installation. Accept the prompts to complete the installation.
4. When the installer completes, select Restart in the dialog box that prompts
you to restart, shut down, or restart later.
Note Ensure that you have installed the latest version of NI
Package Manager. To access the download page for NI Package
Manager, go to ni.com/info and enter info code NIPMDownload.
© National Instruments 5
PXIe-4466/4467/4468 Getting Started Guide
Installing the PXIe-446x
Notice To prevent damage to the PXIe-446x caused by ESD or
contamination, handle the module using the edges or the metal bracket.
Note To maintain forced air cooling in the PXIe system, refer to the
Maintain Forced-Air Cooling document.
1. Ensure the AC power source is connected to the chassis before installing the
module.
The AC power cord grounds the chassis and protects it from electrical damage
while you install the module.
2. Power o the chassis.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior
to installation. Do not install a module if the backplane is damaged.
4. Remove the black plastic covers from all the captive screws on the module
front panel.
5. Identify a supported slot in the chassis. The following figure shows the
symbols that indicate the slot types.
Figure 1. Chassis Compatibility Symbols
1 2 3 4 5
1. PXI Express System Controller Slot
2. PXI Peripheral Slot
3. PXI Express Hybrid Peripheral Slot
4. PXI Express System Timing Slot
5. PXI Express Peripheral Slot
ni.com
6
PXIe-4466/4467/4468 Getting Started Guide
PXIe-446x modules can be placed in PXI peripheral slots or PXIExpress Hybrid
peripheral slots.
6. Touch any metal part of the chassis to discharge static electricity.
7. Ensure that the ejector handle is in the downward (unlatched) position.
8. Place the module edges into the module guides at the top and bottom of the
chassis. Slide the module into the slot until it is fully inserted.
Figure 2. Module Installation
1
2
3
1. Chassis
2. Hardware Module
3. Ejector Handle in Downward (Unlatched) Position
9. Latch the module in place by pulling up on the ejector handle.
10. Secure the module front panel to the chassis using the front-panel mounting
screws.
Note Tightening the top and bottom mounting screws increases
mechanical stability and also electrically connects the front
panel to the chassis, which can improve the signal quality and
electromagnetic performance.
11. Cover all empty slots using either filler panels (standard or EMC) or slot
blockers with filler panels, depending on your application.
© National Instruments 7
PXIe-4466/4467/4468 Getting Started Guide
Note For more information about installing slot blockers and filler
panels, go to ni.com/r/pxiblocker.
12. Power on the chassis.
Conguring the PXIe-446x in MAX
Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX
informs other programs about which NI hardware products are in the system and
how they are configured. MAX is automatically installed with NI-DAQmx.
1. Launch MAX.
2. In the configuration tree, expand Devices and Interfaces to see the list of
installed NI hardware.
Installed modules appear under the name of their associated chassis.
3. Expand your Chassis tree item.
MAX lists all modules installed in the chassis. Your default names may vary.
Note If you do not see your module listed, press <F5> to refresh the
list of installed modules. If the module is still not listed, power o the
system, ensure the module is correctly installed, and restart.
4. Record the identifier MAX assigns to the hardware. Use this identifier when
programming the PXIe-446x.
5. Self-test the hardware by selecting the item in the configuration tree and
clicking Self-Test in the MAX toolbar.
The MAX self-test performs a basic verification of hardware resources.
PXIe-446x Pinout and LEDs
The following figures show the front panel connections of the PXIe-446x.
ni.com
8
PXIe-4466/4467/4468 Getting Started Guide
Note Refer to the module specifications for information about the
operating input and output ranges and overvoltage protection.
Figure 3. PXIe-4466/4467 Front Panel
DSA Analog I/O
ACC ACTIVE
PXIe-4467
AI 0
AI 1
A
O
0
A
O
1
PFI 0
3
2
4
1
2
25
6
2
2
DSA Analog I/O
ACC ACTIVE
PXIe-4466
AI 0
AI 1
A
O
0
A
O
1
PFI 0
3
2
4
1
2
25
6
2
2
1. PFI
2. Chassis Ground
3. AI+
4. AI-
5. AO+
6. AO-
© National Instruments 9
PXIe-4466/4467/4468 Getting Started Guide
Figure 4. PXIe-4468 Front Panel
DSA Analog I/O
ACC ACTIVE
PXIe-4468
AI 0
AI 1
A
O
0
A
O
1
PFI 0
DSA Analog I/O
ACC ACTIVE
PXIe-4468
AI 0
AI 1
A
O
0
A
O
1
PFI 0
3
2
3
4
4
1
2
1
2
5
6
25
6
2
2
1. PFI
2. Chassis Ground
3. AI+
4. AI-
5. AO+
6. AO-
Table 1. Signal Descriptions
Signal Name Signal Description
AI+ Positive analog input signal
AI- Negative analog input signal
ni.com
10
PXIe-4466/4467/4468 Getting Started Guide
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali National Instruments Unità di controllo
National Instruments
National Instruments PXIe-8238 Manuale utente
National Instruments
National Instruments 9871 Manuale utente
National Instruments
National Instruments SCXI-1581 Manuale utente
National Instruments
National Instruments NI 9217 Manuale utente
National Instruments
National Instruments FieldPoint FP-1001 Manuale utente
National Instruments
National Instruments NI 9401 Manuale utente
National Instruments
National Instruments SET-1415 Manuale elenco delle parti
National Instruments
National Instruments 9861 Manuale utente
National Instruments
National Instruments PXIe-7902 Manuale utente
National Instruments
National Instruments sbRIO-9609 Manuale utente
National Instruments
National Instruments SCXI-1141 Manuale utente
National Instruments
National Instruments PXIe-4302 Manuale
National Instruments
National Instruments CompactRIO cRIO-9263 Manuale utente
National Instruments
National Instruments NI PXI-4220 Manuale utente
National Instruments
National Instruments PXI-2503 Manuale utente
National Instruments
National Instruments NI 9402 Manuale utente
National Instruments
National Instruments SCXI-1502 Manuale utente
National Instruments
National Instruments PXI-2568 Manuale utente
National Instruments
National Instruments NI 9237 Manuale utente
National Instruments
National Instruments NI 9930 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
