National Instruments NI-9206 Manuale utente

NI-9206 Getting

Started

2022-07-06

Contents

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Guidelines for Hazardous Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety Guidelines for Hazardous Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Special Conditions for Hazardous Locations Use in Europe and Internationally.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Special Conditions for Marine Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

NI 9206 Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Floating Dierential Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting Grounded Dierential Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting RSE Voltage Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting NRSE Voltage Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting Fuel Cell Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

NI 9206 Connection Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting to a Spring-Terminal Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

High-Vibration Application Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Worldwide Support and Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ni.com

NI-9206 Getting Started

Overview

This document explains how to connect to the NI 9206.

Note Before you begin, complete the soware and hardware installation

procedures in your chassis documentation.

Note The guidelines in this document are specific to the NI 9206. The

other components in the system might not meet the same safety ratings.

Refer to the documentation for each component in the system to

determine the safety and EMC ratings for the entire system.

Safety Guidelines

Operate the NI 9206 only as described in this document.

Caution This icon denotes a caution, which advises you to consult

documentation where this symbol is marked.

NI-9206 Getting Started

Caution Do not operate the NI 9206 in a manner not specified in this

document. Product misuse can result in a hazard. You can compromise the

safety protection built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for repair.

Hazardous Voltage This icon denotes a warning advising you to take

precautions to avoid electrical shock with the NI 9206.

Safety Voltages

Connect only voltages that are within the following limits:

Maximum voltage[1]

AI, PFI0, and D0 to COM ±30 V DC

1 The maximum voltage that can be applied or output between AI and COM without

creating a safety hazard.

Isolation Voltages

Channel-to-channel None

Channel-to-earth ground

Continuous

U.S. (UL 61010-1) 600 V DC, Measurement Category I

Europe (IEC 61010-1) 400 V DC, Measurement Category I

Withstand 2,500 V PK, verified by a 5 s dielectric withstand test

Measurement Category I is for measurements performed on circuits not directly

connected to the electrical distribution system referred to as MAINS voltage. MAINS

is a hazardous live electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary circuits. Such

voltage measurements include signal levels, special equipment, limited-energy

ni.com

NI-9206 Getting Started

parts of equipment, circuits powered by regulated low-voltage sources, and

electronics.

Caution Do not connect the NI 9206 to signals or use for measurements

within Measurement Categories II, III, or IV.

Note Measurement Categories CAT I and CAT O are equivalent. These test

and measurement circuits are for other circuits not intended for direct

connection to the MAINS building installations of Measurement Categories

CAT II, CAT III, or CAT IV.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the following precautions. A

hazardous voltage is a voltage greater than 42.4 Vpk voltage or 60 VDC to earth

ground.

Caution Ensure that hazardous voltage wiring is performed only by

qualified personnel adhering to local electrical standards.

Caution Do not mix hazardous voltage circuits and human-accessible

circuits on the same module.

Caution Ensure that devices and circuits connected to the module are

properly insulated from human contact.

Caution When module terminals are hazardous voltage LIVE (>42.4 Vpk/

60 VDC), you must ensure that devices and circuits connected to the

module are properly insulated from human contact. You must use the

NI 9941 backshell kit to ensure that the terminals are not accessible.

NI-9206 Getting Started

Caution In addition to attaching the connector backshell to the NI 9206,

you must install the entire system in a UL Listed, suitably rated NEMA or IP

enclosure for safe use.

Figure 1. NI 9206 in a Suitably UL Rated NEMA or IP Enclosure

1. Suitably rated NEMA or IP enclosure that requires tool access

2. NI 9206 with NI 9941 connector backshell installed

Safety Guidelines for Hazardous Locations

The NI 9206 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous

locations; Class I, Zone 2, AEx nA IIC T4 Gc and Ex nA IIC T4 Gc hazardous locations;

and nonhazardous locations only. Follow these guidelines if you are installing the

NI 9206 in a potentially explosive environment. Not following these guidelines may

result in serious injury or death.

Caution Do not disconnect I/O-side wires or connectors unless power has

been switched o or the area is known to be nonhazardous.

Caution Do not remove modules unless power has been switched o or

the area is known to be nonhazardous.

Caution Substitution of components may impair suitability for Class I,

Division 2, or Zone 2.

ni.com

NI-9206 Getting Started

Caution The system must be installed in an enclosure certified for the

intended hazardous (classified) location, having a tool secured cover/door,

where a minimum protection of at least IP54 is provided.

Special Conditions for Hazardous Locations Use in Europe and

Internationally

The NI 9206 has been evaluated as Ex nA IIC T4 Gc equipment under DEMKO 03

ATEX 0324020X and is IECEx UL 14.0089X certified. Each NI 9206 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient temperatures of

-40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9206 in Gas Group IIC hazardous locations,

you must use the device in an NI chassis that has been evaluated as Ex nC IIC T4, Ex

IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution Transient protection shall be provided that is set at a level not

exceeding 140% of the peak rated voltage value of 85 V at the supply

terminals to the equipment.

Caution The system shall only be used in an area of not more than

Pollution Degree 2, as defined in IEC/EN 60664-1.

Caution The system shall be mounted in an ATEX/IECEx-certified

enclosure with a minimum ingress protection rating of at least IP54 as

defined in IEC/EN 60079-15.

Caution The enclosure must have a door or cover accessible only by the

use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits

for electromagnetic compatibility (EMC) stated in the product specifications. These

requirements and limits provide reasonable protection against harmful interference

NI-9206 Getting Started

when the product is operated in the intended operational electromagnetic

environment.

This product is intended for use in industrial locations. However, harmful

interference may occur in some installations, when the product is connected to a

peripheral device or test object, or if the product is used in residential or

commercial areas. To minimize interference with radio and television reception and

prevent unacceptable performance degradation, install and use this product in strict

accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved

by National Instruments could void your authority to operate it under your local

regulatory rules.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for marine (shipboard)

applications. To verify Lloyd’s Register certification for a product, visit ni.com/

certification and search for the LR certificate, or look for the Lloyd’s Register mark

on the product.

Caution In order to meet the EMC requirements for marine applications,

install the product in a shielded enclosure with shielded and/or filtered

power and input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes and cables to

ensure that the desired EMC performance is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI 9206 meets the following

specifications.

Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 70 °C

Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

ni.com

NI-9206 Getting Started

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals for complete

specifications.

NI 9206 Pinout

AI0

AI1

AI3

AI5

AI7

AI17

AI19

AI21

AI23

DO0

AI2

AI4

AI6

AI16

AI18

AI20

AI22

COM

AI9

AI8

AI10

AI12

AI14

AI24

AI26

AI28

AI30

AISENSE

AI11

AI13

AI15

AI25

AI27

AI29

AI31

PFI0

Signal Description

AI Analog input signal connection

AISENSE Reference connection for NRSE measurements

COM Common reference connection to isolated ground

DO Digital output signal connection

PFI Programmable function interface, digital input signal connection

Table 1. Signal Descriptions

Signals

You can connect single-ended or dierential signals to the NI 9206. Use a dierential

measurement configuration to attain more accurate measurements and less noise.

NI-9206 Getting Started

The following table shows the signal pairs that are valid for dierential connection

configurations with the NI 9206.

Channel AI + AI-

0 AI0 AI8

1 AI1 AI9

2 AI2 AI10

3 AI3 AI11

4 AI4 AI12

5 AI5 AI13

6 AI6 AI14

7 AI7 AI15

16 AI16 AI24

17 AI17 AI25

18 AI18 AI26

19 AI19 AI27

20 AI20 AI28

21 AI21 AI29

22 AI22 AI30

23 AI23 AI31

Table 2. Dierential Pairs

Connecting Floating Dierential Signals

You can connect floating dierential signals to the NI 9206.

ni.com

NI-9206 Getting Started

Altri manuali per NI-9206

Indice

Altri manuali National Instruments Unità di controllo

National Instruments

National Instruments NI-9361 Manuale

National Instruments

National Instruments Isolated Current Output Module SCC-CO20 Manuale utente

National Instruments

National Instruments VXI-8340 Series Manuale utente

National Instruments

National Instruments NI 9516 Manuale utente

National Instruments

National Instruments PXIe-4480 Manuale utente

National Instruments

National Instruments NI 6520 Manuale utente

National Instruments

National Instruments NI 9265 Manuale utente

National Instruments

National Instruments PXIe-4353 Manuale

National Instruments

National Instruments 9871 Manuale utente

National Instruments

National Instruments PXI Terminal Block NI TB-2708 Manuale utente

National Instruments

National Instruments PXI-6683 Series Manuale utente

National Instruments

National Instruments REM-11178 Manuale utente

National Instruments

National Instruments 9220 Manuale

National Instruments

National Instruments NI 9852 Manuale utente

National Instruments

National Instruments NI 9474 Manuale utente

National Instruments

National Instruments 9266 Manuale utente

National Instruments

National Instruments SCC-FT01 Manuale utente

National Instruments

National Instruments NI-5783 Manuale utente

National Instruments

National Instruments NI PCIe-1430 Manuale utente

National Instruments

National Instruments PXIe-8861 Manuale utente

National Instruments

National Instruments Module SCXI-1125 Manuale

National Instruments

National Instruments PXI-2503 Manuale utente

National Instruments

National Instruments NI 9203 Manuale

National Instruments

National Instruments ATCA-3671 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente