National Instruments PXIe-8521 Manuale utente

USER MANUAL

PXIe-8521

4-port, 100BASE-T1 PXI Automotive Ethernet Interface Module

This document explains how to install and configure the PXIe-8521 module.

Contents

Introduction...............................................................................................................................1

Getting Started.......................................................................................................................... 2

Installing the PXIe-8521................................................................................................... 2

PXIe-8521 Pinout..............................................................................................................4

Connection Guidelines......................................................................................................4

Port Modes........................................................................................................................ 5

PHY State..........................................................................................................................8

Configuring the PXIe-8521 in MAX................................................................................ 9

Programming the PXIe-8521............................................................................................ 9

LED Functionality...................................................................................................................10

Synchronization Methods....................................................................................................... 10

Local Time...................................................................................................................... 10

Network Time..................................................................................................................11

Host Time........................................................................................................................ 11

PXI Triggers.................................................................................................................... 11

Introduction

Kit Contents

• PXIe-8521 module

• 26 AWG x 8 mm insulated ferrules, x 20

• Screw driver for use with connector spring terminal push buttons

•PXIe-8521 Safety, Environmental, and Regulatory Information

Note The PXIe-8521 ships with plug connectors pre-installed on each port.

Getting Started

Installing the PXIe-8521

Notice To prevent damage to the PXIe-8521 caused by ESD or contamination,

handle the module using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the module.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the module.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic covers from all the captive screws on the module front panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 1. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

PXIe-8521 modules can be placed in PXI Express peripheral slots, PXI Express hybrid

peripheral slots, or PXI Express system timing slots.

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the downward (unlatched) position.

8. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the module into the slot until it is fully inserted.

2| ni.com | PXIe-8521 User Manual

Figure 2. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Downward (Unlatched) Position

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the module front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

11. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize

cooling air flow, depending on your application.

12. Power on the chassis.

PXIe-8521 User Manual | © National Instruments | 3

PXIe-8521 Pinout

Figure 3. PXIe-8521 Pinout

PORT 1

LINK/

ACT

STATUS

TAP

PORT 2

LINK/

ACT

STATUS

PORT 3

LINK/

ACT

STATUS

TAP

PORT 4

LINK/

ACT

STATUS

PXIe-8521

100BASE-T1

PORT 1

LINK/

ACT

STATUS

Link/Act

LED

Port Identification

Status

LED

Pin 1

Pin 2

Pin 3

Tap

Pairs

Ports

Table 1. PXIe-8521 Pinout Signal Descriptions

Pin Number Signal Type Signal Direction Signal Description Signal Required

1 TRX_P Bi-directional Transceiver plus Required

2 TRX_M Bi-directional Transceiver minus Required

3 Shield — Shield Optional

Connection Guidelines

Notice Operate this product only with cables less than 15 m in length.

4| ni.com | PXIe-8521 User Manual

1. Push a solid wire or ferrule directly into the terminal.

2. When inserting a stranded wire without a ferrule, first open the terminal by pressing the

push button with a finger or the included screwdriver tool.

3. Verify that all strands of a stranded wire are securely retained.

4. Insulated ferrules are recommended for small-gauge stranded wire. 26 AWG x 8 mm

barrel length insulated ferrules are included with the product.

Note A ferrule crimping tool is not included with this product.

5. Tighten the connector screw flanges to the torque specification in the PXIe-8521

Specifications for the best shock and vibration performance. The connector screw flanges

ship in a non-torqued configuration for easy removal.

6. When removing a wire, first open the terminal by pressing the push button with a finger

or the included screwdriver tool.

Port Modes

The PXIe-8521 includes four ports that can be configured as independent network interfaces

on the module. The ports can function in Direct mode or Tap mode. Regardless of mode,

traffic on each port can be monitored. When monitoring is enabled, all traffic that is

transmitted or received on that port is captured. Each packet is timestamped by both the local

time keeper and the port's network time keeper. The local time keeper runs off PXI Clk10 if

present on the chassis. Each port has an independent network time keeper, which uses IEEE

802.1AS to synchronize time with other devices on the network.

Note Port mode cannot be changed while an XNET session is started on the port.

When the port mode is changed, port connectivity is lost while the change is

configured.

Data Path Overview

The following diagram describes each port within the PXIe-8521.

PXIe-8521 User Manual | © National Instruments | 5

Figure 4. PXIe-8521 Block Diagram

PXIe-8521

User Application

PXIe Controller

XNET OS Stack

Intel i210

XNET

Monitor

XNET

Endpoint

DUT

802.1AS

Firmware

MAC

PHY

Each port has three data paths: XNET monitor, XNET endpoint, and OS stack. All three data

paths can be used simultaneously depending on port mode. The monitor path reads and

inspects all Ethernet frames that are received or transmitted on the port. The endpoint path

transmits and receives Ethernet frames on the port. The endpoint path is typically used if you

need it to act as an AVB endpoint. The OS stack path transmits and receives data using

standard network sockets via the operating system's network stack. The OS stack is typically

used with applications designed to use traditional TCP- or UDP-based protocols for its

network communication.

Note The PXIe-8521 does not support jumbo frames.

For Ethernet interfaces, the suffix "/monitor" indicates the use of a monitor path when it is

appended to the interface name. For example, "ENET1" specifies use of the endpoint path, and

"ENET1/ monitor" specifies use of the monitor path. The monitor path is used to read Ethernet

frames that are received or transmitted on each port. When Tap is enabled, data received via

the monitor path by a Tap pair will be identical on each port in the pair.

The IEEE 802.1AS protocol is implemented by the firmware running on the PXIe-8521, and

packet timestamps are taken near the device's physical layer. This helps guarantee a high

degree of synchronization accuracy for each port's network time.

6| ni.com | PXIe-8521 User Manual

Direct Mode

The following diagram describes Direct mode on the PXIe-8521.

Figure 5. Direct Mode

PXIe-8521

User Application

PXIe Controller

XNET OS Stack XNET

XNET

Endpoint Intel i210 Intel i210 XNET

Endpoint

DUT1

MAC

PHY

DUT2

MAC

PHY

Note This diagram shows a design with two ports. Each of the device's four ports

can run independently under Direct mode.

Note Although it is not shown in the diagram, you can simultaneously use the

XNET monitor data path on each port while it is in Direct mode. This allows you to

analyze all network traffic that is transmitted and received on the port's endpoint.

In Direct mode, ports are directly connected and function as endpoints; Ethernet frames

received and transmitted on the port have no relationship to any other ports on the device.

Input and output sessions are supported in Direct mode. The PXIe-8521 supports up to four

ports using Direct mode.

Tap Mode

In Tap mode, a pair of adjacent ports on the device, called tap partners, are connected to form a

Tap that allows the PXIe-8521 to monitor traffic. In Tap mode, physical Port 1 and Port 2 are

PXIe-8521 User Manual | © National Instruments | 7

Tap partners, and Port 3 and Port 4 are Tap partners. A frame received on one Tap partner is

transmitted out of the other Tap partner, which mimics the behavior of an Ethernet cable.

Note For more information about Tap latency, refer to the PXIe-8521

Specifications.

When an input session is created using an XNET interface for either Tap partner, and the "/

monitor" suffix is used with the XNET interface, the session reads frames going through the

Tap partners. Output sessions are not supported in Tap mode.

Note You only need to select the monitor of one port in the Tap pairing. If both

monitors are selected, you will receive the same data twice.

Setting one port to Tap mode will automatically set the port's Tap partner to Tap mode. The

PXIe-8521 supports two Taps (Ports 1/2 and Ports 3/4) using this mode. All four ports can also

be used simultaneously while one pair is in Tap mode and the other ports are in Direct mode.

The following diagram describes one Tap pair on the PXIe-8521.

Figure 6. Tap Mode

PHY

XNET

Monitor

PHY

PXIe-8521

DUT1 DUT2

User Application

XNET XNET

PXIe Controller

PHY State

The PXIe-8521 PHY's master/slave state can be configured for communication with its peer

PHY. In traditional Ethernet networks, this master/slave state is negotiated automatically at the

PHY level. However, in Automotive Ethernet networks such as IEEE 100BASE-T1, the

master/slave state is commonly configured statically and is typically determined by the PHY

state setting of the connected DUT. Configure the PHY state of the PXIe-8521's port to the

opposite of the connected DUT's PHY state.

8| ni.com | PXIe-8521 User Manual

Configuring the PXIe-8521 in MAX

Use Measurement & Automation Explorer (MAX) to configure your National Instruments

hardware. MAX informs other programs about which devices reside in the system and how

they are configured.

1. Launch MAX.

2. In the configuration tree, expand Devices and Interfaces to see the list of installed NI

hardware.

Note If you do not see your module listed, press <F5> to refresh the list of

installed modules. If the module is still not listed, power off the system, ensure

the module is correctly installed, and restart.

3. Expand your module to see the list of ports.

4. Record the NI-XNET interface name that MAX assigns to each port of the hardware. Use

this name when programming the PXIe-8521.

5. For each port, configure the port mode to either Direct or Tap, depending on whether you

want to fully participate in network communication as an endpoint (Direct) or monitor an

existing network connection (Tap).

6. For each port, configure the PHY state to either Master or Slave, depending on the

corresponding state of the PHY that you are connecting to.

Note Two PHYs that are physically connected must be configured to use

opposing PHY states. One PHY must be configured to be the master, and the

other PHY must be configured to be the slave.

7. Self-test the hardware by selecting the item in the configuration tree and clicking Self-

Test in the MAX toolbar.

The MAX self-test performs a basic verification of hardware resources.

Programming the PXIe-8521

You can program the PXIe-8521 using both the NI-XNET API and the operating system's

standard network stack API. Both APIs can be used simultaneously. Select an API based on

the needed function, listed below:

API Functionality

NI-XNET • Monitor

• AVB endpoint

• IEEE 802.1AS synchronization

• Trigger synchronization

• Port configuration

Operating System Network Stack • Network sockets (TCP/IP and UDP/IP)

NI-XNET provides many of the advanced data access and timing & synchronization

capabilities for the device, while availability of the OS network stack provides a

PXIe-8521 User Manual | © National Instruments | 9

straightforward way to integrate applications that rely on standard network sockets for their

network communication.

LED Functionality

The PXIe-8521 includes two LED indicators per port to help you monitor hardware and bus

status.

LED Label LED State LED Color Condition

LINK/ACT Off — No link established

Default power-up state

Solid Green Link established, 100 Mbits/s

Blinking Green Activity, 100 Mbits/s

STATUS Off — Default power-up state

Solid Green Direct Mode, master (PHY state)

Amber Direct Mode, slave (PHY state)

Fade in and out1Green Tap Mode, master (PHY state)

Amber Tap Mode, slave (PHY state)

Blinking Green Port ID

Amber Not synchronized

Red Catastrophic error2

Synchronization Methods

The PXI and PXI Express chassis feature a dedicated synchronization bus integrated into the

backplane. NI-XNET products support use of this bus to synchronize with other National

Instruments hardware products such as DAQ, IMAQ, and NI Motion Control. The PXI

synchronization bus consists of a flexible interconnect scheme for sharing timing and

triggering signals in a system.

Local Time

The PXIe-8521 uses PXI_Clk10, a 10 MHz PXI backplane clock, to drive the local time

keeper and to synchronize with other modules in the PXI chassis. If the PXI backplane clock is

not available, the PXIe-8521 uses an internal oscillator.

1When in Tap Mode, ports that are paired fade in phase with each other, but out of phase with other

ports.

2In the case of a catastrophic error, recover by invoking Reset on the module in MAX. Contact NI

for further support if the error continues to occur.

10 | ni.com | PXIe-8521 User Manual

Indice

Altri manuali National Instruments Unità di controllo

National Instruments

National Instruments 9472 Manuale utente

National Instruments

National Instruments CompactRIO cRIO-FRC Manuale utente

National Instruments

National Instruments NI 9512 Manuale utente

National Instruments

National Instruments NI 9930 Manuale utente

National Instruments

National Instruments SCXI-1100 Manuale utente

National Instruments

National Instruments NI 6520 Manuale utente

National Instruments

National Instruments PXIe-4466 Manuale utente

National Instruments

National Instruments NI 9475 Manuale utente

National Instruments

National Instruments NI 9213 Manuale utente

National Instruments

National Instruments NI 9214 Manuale utente

National Instruments

National Instruments 7330 Manuale utente

National Instruments

National Instruments sbRIO-9205 Manuale utente

National Instruments

National Instruments NI 9757 Manuale utente

National Instruments

National Instruments NI 9265 Manuale utente

National Instruments

National Instruments PC/104-GPIB Manuale utente

National Instruments

National Instruments NI 9881 Manuale utente

National Instruments

National Instruments NI 9221 Manuale utente

National Instruments

National Instruments NI 9262 Manuale utente

National Instruments

National Instruments SCXI-1521 Manuale utente

National Instruments

National Instruments ISM-7400 Manuale utente

National Instruments

National Instruments NI 9263 Manuale

National Instruments

National Instruments Relay Module SCC-RLY01 Manuale utente

National Instruments

National Instruments FIeldPoint FP-AO-200 Manuale utente

National Instruments

National Instruments 9205 Manuale

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente