National Instruments Two-Slot Embedded Controller NI PXI-8183 Manuale utente

INSTALLATION GUIDE

NI PXI-8183

This document contains information about installing your NI PXI-8183

controller in a PXI chassis.

For complete configuration and troubleshooting information

(including information about BIOS setup, adding RAM, and so on), refer

to the NI PXI-8183 User Manual. The manual is in PDF format on the

documentation CD included with your controller, and the National

Instruments Web site, ni.com.

Installing the NI PXI-8183

This section contains general installation instructions for the NI PXI-8183.

Consult your PXI chassis user manual for specific instructions and

warnings.

1. Plug in your chassis before installing the NI PXI-8183. The power cord

grounds the chassis and protects it from electrical damage while you

install the module. (Make sure the power switch is turned off.)

Caution To protect both yourself and the chassis from electrical hazards, leave the chassis

powered off until you finish installing the NI PXI-8183 module.

2. Remove any filler panels blocking access to the system controller slot

(Slot 1) in the chassis.

3. Touch the metal part of the case to discharge any static electricity that

might be on your clothes or body.

4. Remove the protective plastic covers from the four bracket-retaining

screws as shown in Figure 1.

NI PXI-8183 Installation Guide 2 ni.com

Figure 1. Removing Protective Screw Caps

5. Make sure the injector/ejector handle is in its downward position.

Align the NI PXI-8183 with the card guides on the top and bottom

of the system controller slot.

Caution Do not raise the injector/ejector handle as you insert the NI PXI-8183. The

module will not insert properly unless the handle is in its downward position so that it does

not interfere with the injector rail on the chassis.

6. Hold the handle as you slowly slide the module into the chassis until

the handle catches on the injector/ejector rail.

7. Raise the injector/ejector handle until the module firmly seats

into the backplane receptacle connectors. The front panel of the

NI PXI-8183 should be even with the front panel of the chassis.

8. Tighten the four bracket-retaining screws on the top and bottom of the

front panel to secure the NI PXI-8183 to the chassis.

9. Check the installation.

10. Connect the keyboard and mouse to the appropriate connectors. If you

are using a PS/2 keyboard and a PS/2 mouse, use the Y-splitter adapter

included with your controller to connect both to the PS/2 connector.

1 Protective Screw Cap (4X)

©National Instruments Corporation 3 NI PXI-8183 Installation Guide

11. Connect the VGA monitor video cable to the VGA connector.

12. Connect devices to ports as required by your system configuration.

13. Power on the chassis.

14. Verify that the controller boots. If the controller does not boot, refer to

the What If the NI PXI-8183 Does Not Boot? section.

Figure 2 shows an NI PXI-8183 installed in the system controller slot of a

National Instruments PXI-1036 chassis. You can place PXI devices in any

other slot.

Figure 2. NI PXI-8183 Controller Installed in a PXI Chassis

How to Remove the Controller from the PXI Chassis

The NI PXI-8183 controller is designed for easy handling. To remove the

unit from the PXI chassis:

1. Power off the chassis.

2. Remove the bracket-retaining screws in the front panel.

3. Press the injector/ejector handle down.

4. Slide the unit out of the chassis.

1 PXI-1036 Chassis 2 NI PXI-8183 Controller 3 Injector/Ejector Rail

NATIONAL

INSTRUMENTS

NI PXI-1036

LOW POWER

National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.

Refer to the Terms of Use section on ni.com/legal for more information about National

Instruments trademarks. Other product and company names mentioned herein are trademarks or trade

names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your CD, or

ni.com/patents.

What If the NI PXI-8183 Does Not Boot?

Several problems can cause a controller not to boot. Here are some things

to look for and possible solutions.

Things to Notice:

• Which LEDs come on? The Power OK LED should stay lit.

The Drive LED should blink during boot as the disk is accessed.

• What appears on the display? Does it hang at some particular point

(BIOS, Operating System, and so on)? If nothing appears on the

screen, try a different monitor. Does your monitor work with a

different PC? If it hangs, note the last screen output that you saw for

reference when consulting National Instruments technical support.

• What has changed about the system? Did you recently move the

system? Was there electrical storm activity? Did you recently add

a new module, memory chip, or piece of software?

Things to Try:

• Make sure the chassis is plugged in to a working power source.

• Check any fuses or circuit breakers in the chassis or other power

supply (possibly a UPS).

• Make sure the controller module is firmly seated in the chassis.

• Remove all other modules from the chassis.

• Remove any nonessential cables or devices.

• Try the controller in a different chassis or a similar controller in this

same chassis.

• Recover the hard drive on the controller. (Refer to the Hard Drive

Recovery section in the NI PXI-8183 User Manual.)

• Clear the CMOS. (Refer to the System CMOS section in the

NI PXI-8183 User Manual.)

For more troubleshooting information, refer to the NI PXI-8183 User

Manual. The manual is in PDF format on the documentation CD included

with your controller, and the National Instruments Web site, ni.com.

Altri manuali per Two-Slot Embedded Controller NI PXI-8183

Indice

Altri manuali National Instruments Controllori

National Instruments

National Instruments NI cDAQ-9134 Manuale del proprietario

National Instruments

National Instruments PXI-8109 Manuale utente

National Instruments

National Instruments cRIO-9064 Manuale utente

National Instruments

National Instruments PXI-8115 Manuale utente

National Instruments

National Instruments cRIO-9032 Manuale utente

National Instruments

National Instruments NI PXI-8104 Manuale utente

National Instruments

National Instruments sbRIO-9637 Manuale utente

National Instruments

National Instruments cRIO-904 Series Manuale utente

National Instruments

National Instruments CompactRIO cRIO-9025 Manuale utente

National Instruments

National Instruments 187970E-01 Manuale utente

National Instruments

National Instruments GPIB GPIB-ENET/100 Manuale utente

National Instruments

National Instruments 73 Series Manuale utente

National Instruments

National Instruments cRIO-9033 Manuale utente

National Instruments

National Instruments RMC-8354 Manuale utente

National Instruments

National Instruments NI 9683 Manuale utente

National Instruments

National Instruments PXI Express Series Manuale utente

National Instruments

National Instruments GPIB-232 Manuale utente

National Instruments

National Instruments NI PXIe-8840 Manuale utente

National Instruments

National Instruments DAQ-STC Series Manuale del prodotto

National Instruments

National Instruments CVS-1457RT Manuale utente

National Instruments

National Instruments cDAQ-9133 Manuale utente

National Instruments

National Instruments NI cRIO-9036 Manuale utente

National Instruments

National Instruments cRIO-9034 Manuale utente

National Instruments

National Instruments CompactRIO NI cRIO-9012 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente