Nautel VS1 Manuale utente

VS1 Transmitter

Installation Manual

Document:NHB-VS1-INS

Issue: 10.0 2018-10-29

Status: Standard

Nautel Limited

10089 Peggy’s Cove Road

Hackett’s Cove, NS Canada B3Z 3J4

Phone: +1.902.823.3900 or

Toll Free: +1.877.6NAUTEL (6628835) (Canada & USA only)

Fax: +1.902.823.3183

Nautel Inc.

201 Target Industrial Circle

Bangor, Maine USA 04401

Phone: +1.207.947.8200

Fax: +1.207.947.3693

Customer Service (24 hour support)

+1.877.628.8353 (Canada & USA only)

+1.902.823.5100 (International)

Email: [email protected]

Web: www.nautel.com

The comparisons and other information provided in this document

have been prepared in good faith based on publicly available

information. The reader is encouraged to consult the respective

manufacturer's most recent published data for verification.

© Copyright 2018 NAUTEL. All rights reserved.

VS1 Installation Manual Table of contents

Page v

Contents

Release control record vii

Preparing for installation 1-1

Mounting the transmitter 2-1

Connecting to station reference ground 3-1

Installing the RF feed line 4-1

Connecting ac power 5-1

Installing program inputs 6-1

Planning 6-1

Connecting cables 6-1

Installing control and monitoring wiring 7-1

Planning 7-1

Connecting cables 7-1

Commissioning 8-1

Pre-Commissioning 8-2

Commissioning 8-3

Network Setup 8-7

Changing the OS Password 8-9

VS1 Installation Manual

Page vi Issue 10.0 2018-10-29

Parts and tools 9-1

Contacting Nautel 9-1

Parts supplied by Nautel 9-2

Parts not supplied by Nautel 9-2

Parts ordering 9-2

Module replacement program 9-3

Tools for installation 9-3

Pre-installation / Installation assistance 10-1

Pre-installation consulting 10-1

Installation and commissioning service 10-1

Online documentation 10-3

On-site support 10-3

Training 10-4

Standard warranty 10-5

Extended warranties 10-8

List of terms 11-1

VS1 Installation Manual

Issue 10.0 2018-10-29 Page vii

Release control record

Issue Date Reason

10.0 2018-10-29 Hardware Release 10 (NARF65I and NARF65I/01).

Supports software version VS SW 5.2 and higher.

VS1 Installation Manual

Page viii Issue 10.0 2018-10-29

VS1 Installation Manual Preparing for installation

Issue 10.0 2018-10-29 Page 1-1

Section 1: Preparing for installation

Before installing your VS1 transmitter, perform the following steps:

1. Ensure that you have performed the pre-installation tasks described in the 

VS1 Pre-installation Manual.

2. Inspect the shipping box for damage. Report any damage immediately to your Nautel sales

representative and the carrier.

3. Unpack the box. Remove all items from packing and place them on a suitable work area.

Check your packing list to make sure that you received all the components, including the

VS1, VS1 Quick Start Guide, VS1 USB device (contains technical manual set and

unpacking/installation video), installation kit and ancillary kit.

4. Assemble your parts and tools. For a list of required tools, see “Parts and tools” on page 9-1.

5. When you are ready to install the VS1 transmitter, follow the steps shown in Figure 1.1 on

page 1-2.

TIP When you have completed a task or step, put a check mark beside the step

number.

Note:



The VS1 Quick Start Guide provides a more streamlined method to unpack, install and

commission your transmitter. If you used the Quick Start Guide to successfully commission your

transmitter, Nautel recommends you use the information in this Installation Manual to verify

your installation or for more in-depth information, as required.

CAUTION: 

FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR MANUFACTURER’S

WARRANTY. FOR MORE INFORMATION, REVIEW YOUR WARRANTY DOCUMENTS.

VS1 Installation Manual Preparing for installation

Page 1-2 Issue 10.0 2018-10-29

Figure 1.1: Flowchart - Installing the transmitter

Mounting the transmitter - see page 2-1

Connecting to station reference ground - see page 3-1

Installing control and monitoring wiring - see page 7-1

Commissioning - see page 8-1

Perform operational tasks:

“Commissioning” and “Going On-Air”, beginning on page 8-3

Installing the RF feed line - see page 4-1

Installing program inputs - see page 6-1

Connecting ac power - see page 5-1

Altri manuali per VS1

5

Indice

Altri manuali Nautel Trasmettitore

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente