NetComm 3G25W-R Manuale utente
Overview
The NetComm 3G25W-R integrates a Wireless LAN and 3G WAN into
one unit. Connection to the Internet is achieved through either a 3G
service or via a fixed line xDSL/Cable/Satellite connection to the
3G25W-R’s WAN port, providing you with the flexibility to choose how
you access the Internet. The 3G25W-R’s automatic failover ensures
you are always connected by activating the 3G connection should the
xDSL/Cable/Satellite connection drop out.
Users are able to share a single 3G connection via both a wired and
wireless connection to the 3G25W-R. With a built in 802.11n wireless
access point, this router provides wireless speeds of up to 150Mbps,
150% faster than 11g technology¹. On top of this, the 3G25W-R has
four LAN ports for wired connections to multiple devices. Rather than
being restricted to certain USB modems, the 3G25W-R allows the
user to simply insert an active SIM and utilise 3G Mobile Broadband
for internet connectivity.
The 3G25W-R includes advanced security features such as VPN
pass-through, a full complement of wireless security options and a
built in firewall.
1 Maximum wireless signal rate and coverage values are derived from IEEE Standard 802.11g and
802.11n Draft 2.0 specifications. Actual wireless speed and coverage are dependent on network and
environmental conditions included but not limited to volume of network traffic, building materials and
construction/layout.
3G25W-R Features:
Powerful wireless router with support for 3G Mobile Broadband
Creates instant Wireless hotspots to share the Internet
connection of a 3G USB modem or DSL/Cable modem
Supports Wireless N standard with data speeds up to
150Mbps¹
One WAN port for alternate wired Internet connection
(DSL/Cable/Satellite via Ethernet)
Four LAN ports to connect wired devices like PCs or gaming
consoles
Ensures connectivity and business continuity with auto Internet
failover from WAN port to 3G Mobile Broadband
Easy WiFi Protected Setup (WPS) by the single touch of a
button to establish a secure wireless connection
Full Wireless security - WEP, WPA, WPA2
Browser based interface for configuration and management:
OS independent and easy to use
Package Contents
Your 3G25W-R Wireless Router with voice Package contains the
following items:
3G25W-R Wireless Router
Quick Installation Guide
User Guide on CD
Power Supply Unit
Ethernet Cable
If any of the above items are damaged or missing, please contact your
dealer immediately.
Minimum System Requirements
Before continuing with the installation of your 3G25W-R Wireless
Router, please confirm that you comply with the minimum system
requirements.
Active SIM card for 3G Broadband access if you want to use a
3G Broadband service.
Note: Subject to terms and conditions from your 3G Broadband Internet Service.
Computer with Windows, Macintosh, or Linux-based operating
systems with a working Ethernet adapter with TCP/IP Protocol
installed.
Internet Explorer version 6.0 or Netscape Navigator version 7.0
and above.
Wireless Computer System Requirements
Computer with a working 802.11b, 802.11g, 802.11n wireless
adapter
LED indicators:
(PICTURES)
LED color Description
Status Green in flash Device status is working.
Red in flash Disconnected.
No SIM card / signal or unverified
PIN code
Amber in flash Connecting.
Red Connected.
Signal strength in level one
(weak)
Red in quick flash Roaming alert, and 3G signal is
weak
3G Signal Strength LED
Amber Connected.
Signal strength in level two or
three (middle)
Amber in quick flash Roaming alert, and 3G signal is
middle
Green Connected.
Signal strength in level four or
five (strong)
Green in quick flash Roaming alert, and 3G signal is
strong
Green EDGE or GPRS connection is
established
2G/2.5G LED
Green in flash Data packet transferred via
2G/2.5G
Green UMTS/HSDPA/HSUPA
connection is established
3G/3.5G LED
Green in flash Data packet transferred via
3G/3.5G
USB / 3G LED Green Connected with 3G dongle via
USB port
Green RJ45 cable is pluggedWAN LED
Green in flash Data access
Green RJ45 cable is pluggedLAN LED
Green in flash Data access
Green WLAN is on
Green in flash Device is in WPS PBC mode
WiFi LED
Green in fast flash Device is in WPS PBC mode
Restoring Factory Defaults
This feature will reset the Router to its factory default configuration. Occasions may present
themselves where you need to restore the factory default settings on your router. Typical
situations are:
You have lost your password and unable to login to the router;
You have purchased the router from someone else and need to reconfigure the
device.
You are asked to perform a factory reset by a member of the excellent NetComm
Support Staff.
In order to restore your router to its factory default settings, please follow these steps:
Ensure that the router is powered on (for at least 20 seconds).
Use a paper clip or a pencil tip to depress the reset button for ten seconds and
release. At this point, the reset is in progress. Do not power off the unit at this point.
After the router reboots, the default settings are now restored. This entire process
takes several minutes to complete.
Once you have reset the router to its default settings you will be able to access the
device’s web configuration using http://192.168.1.1 with password “admin”.
Default Settings
LAN (Management)
Static IP Address:192.168.1.x
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
WAN (Internet)
WAN mode: DHCP
WirelessSSID: (refer to the wireless security card insert)
Security: WPA2-PSK
WEP Key: (refer to the wireless security card insert)
Modem Access
Password: admin
Connecting your 3G25W-R Wireless Router
Step 1: Attach the antenna.
1. Remove the antenna from its plastic wrapper.
2. Screw the antenna in a clockwise direction to the back panel of the unit.
3. Once secured, position the antenna upward at its connecting joint. This will ensure optimal
reception.
4. And pull out the “USIM/SIM & PWR” labelled tag.
5. Ensure the Power Switch is off.
DO NOT connect the 3G25W-R to power before performing the installation
steps below.
Step 2: Insert a SIM/USIM into the 3G25W-R.
Step 3: Insert the Ethernet cable into the LAN Port:
Insert the Ethernet cable into LAN port on the back panel of the 3G25W-R, and an available
Ethernet port on the network adapter on the computer you will use to configure the 3G25W-R.
Step 4: Power on the 3G25W-R:
1. Connect the power adapter to the receptor on the back panel of your 3G25W-R.
2. Then plug the other end of the power adapter into a wall outlet or power strip.
3. Turn on the Power Switch.
Step 5: Complete the setup.
1. All LEDs will flash to indicate power has been applied.
2. The LEDs will flash ON and OFF as the 3G25W-R performs its startup initialisation and
Internet connection processes. This will take a few minutes.
3. When complete, the Status LED will flash.
SettingupyourPC
Having physically connected your 3G25W-R, the next step is to configure the router to
establish a broadband connection. Depending on your computers current settings you may
first need to reconfigure the TCP/IP (Network Settings) to access your Wireless Router.
Follow the instructions for your operating system.
ForWindows98SE/ME/2000/XP
1. Click on “Start” -> “Control Panel” (in Classic View). In the Control Panel; double click on
“Network Connections” to continue.
2. Single RIGHT click on “Local Area connection”, then click “Properties”.
3. Double click on “Internet Protocol (TCP/IP)”.
4. Check “Obtain an IP address automatically” and “Obtain DNS server address automatically”
then click on “OK” to continue
5. Click “Show icon in notification area when connected” (see screen image in 3. above) then click on
“OK” to complete the setup procedures.
ForWindowsVista32/64
1. Click on “Start” -> “Control Panel” -> “Network and Sharing Center”.
2. In the Manage network connections, click on “Manage network connections” to continue.
3. Single RIGHT click on “Local Area connection”, then click “Properties”.
4. The screen will display the information “User Account Control” and click “Continue” to continue.
5. Double click on “Internet Protocol Version 4 (TCP/IPv4)”.
6. Check “Obtain an IP address automatically” and “Obtain DNS server address automatically”
then click on “OK” to continue.
Indice
Altri manuali NetComm Router di rete
NetComm
NetComm Dynalink MyZone 3G24W Manuale utente
NetComm
NetComm 3G9WB Manuale di istruzioni
NetComm
NetComm Freshtel NB9 Manuale utente
NetComm
NetComm NB4 Manuale utente
NetComm
NetComm V100 Manuale utente
NetComm
NetComm G.SHDSL 4-port Security Modem Routers NB712 Manuale utente
NetComm
NetComm NTC-6000 SERIES Manuale utente
NetComm
NetComm NB16WV Manuale utente
NetComm
NetComm NB9WMAXXn Manuale utente
NetComm
NetComm XBox NF1901ACV Manuale utente
NetComm
NetComm Whitepaper TR-069 Manuale utente
NetComm
NetComm Smart Hub 4G Manuale utente
NetComm
NetComm NP290W Manuale utente
NetComm
NetComm Freshtel NB9 Manuale utente
NetComm
NetComm NWL-15 Manuale utente
NetComm
NetComm NB5PLUS4 Manuale utente
NetComm
NetComm NB14 Manuale utente
NetComm
NetComm NB5PLUS4 Manuale utente
NetComm
NetComm N3G002W Guida rapida
NetComm
NetComm Poe01 Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza