Nordval DC202-2CH Manuale utente
HELLO,
Thank you for purchasing the DC202-2CH dashcam. Let’s get started!
TABLE OF CONTENTS
Declaration of conformity
What’s in the box
Installing your dashcam
Installing with Nordväl Power Kit USB-C (optional)
Connecting to the app
App options
Setting the parking mode
Playback recordings on PC
Voice control & voice guidance
Frequently asked questions
Product specifications
04
05
07
09
11
12
16
17
18
19
21
3
English
DECLARATION OF CONFORMITY
Product information
For the following
Product: Dashcam
Type: DC202-2CH
Declaration and applicable standards
Hereby, TJM Supplies B.V. declares that the type of dashcam DC202-2CH series
conforms to: Directive EMC 2014/53/EU and the RoHS directive (2011/65/EU) and its
amendment directives 2015/863/EU on the restriction of the use of certain
hazardous substances in electronic equipment.
The full text of the EU declaration of conformity can be found at the following internet
address: www.nordval.eu/declaration-of-conformity/
Importer
Company: TJM Supplies B.V.
Address: Zompstraat 8
8102 HX Raalte
The Netherlands
Email: [email protected]
Phone number: +31 85-0402973
Chamber of Commerce number: 72016981
VAT number: NL858946439B01
Nordväl® is the registered trademark of TJM Zwerink Holding B.V.
Specifications are subject to change without notice.
Copyright© 2023 TJM Supplies B.V. All rights reserved.
Manufactured in China.
4
5
WHAT’S IN THE BOX
Please check the box for each of the following items before installing your dashcam:
Nordväl DC202-2CH front and rear camera
Micro SD card
USB-C power cable (3.5m) + USB car charger
AV cable rear camera (6m)
Electrostatic films
5x Cable clips + pry tool
Extra adhesive tape
DC202-2CH Details
Windshield mounting
2K lens
4K lens
Blue LED light
Red LED light
Micro SD card slot
USB-C port
English
Speaker
GPS antenna
Function button
White indicator light
Windshield mounting
Reset pin
User manual
6
DC202-2CH Buttons & functions
Button Function Instructions
Function
button
Record audio toggle
button Press the button once to activate or
deactivate audio recording.
DC202-2CH LED status
LED light Meaning
Blue
If the blue light flashes, the dashcam is recording.
If the blue light is solid, the dashcam is powered on but not recording.
Red If the red light flashes, the SD card cannot be read.
If the red light is solid, that the SD card needs to be formatted.
Blue /
Red
If the red light and the blue light flash alternately, an “event
recording” is taking place.
If the red light and the blue light flash simultaneously, an update or
message is ongoing.
Press and hold the function button for 10
seconds to reset the WiFi password +
format SD card.
SD card format + WiFi
password restoring
White If the white light is solid, audio recording is on.
If the white light is off, audio recording is off.
7
INSTALLING YOUR DASHCAM
English
Caution
•
•
Do not install the product in a location where it may obstruct
the driver’s field of vision.
Attach the camera to the windshield, behind the rear-view
mirror. Clean and dry the windshield before installation.
Turn off the engine. Carefully insert
the micro SD card into the micro SD
card slot until it clicks.
1Remove the plastic film from the
front camera. Remove the
protective film from the adhesive
tape.
2
Attach the camera to the
windshield, behind the rear-view
mirror. If desired, stick the
electrostatic film between the
windshield and the dashcam.
3Adjust the angle of the lens by
rotating the camera about 10°
downwards. This ensures that the
camera records with a good aspect
ratio. It is recommended to
maintain a ratio of 2/3 road and 1/3
horizon.
4
7
Plug the 12V power cable into the
car’s cigarette lighter and plug the
cable into the dashcam.
5Remove the plastic film from the
rear camera. Remove the protective
film from the adhesive tape.
6
8
Start the engine. The dashcam powers up and starts recording. Video files are stored
on the micro SD card. When the micro SD card is full, the newest video files will
replace the oldest video files (loop recording). This means that the SD card always
contains the most recent recordings.
8
Attach the camera to the rear window in a place where the view is not obstructed.
Place the rear camera in such a way that the adhesive edge is on the right side as
shown in the image above.
7
If the rear camera image is upside down or mirrored, you can correct this in
the app settings.
Note
INSTALLING WITH NORDVÄL POWER
KIT USB-C
Caution
•
•
Read this manual carefully before installation and, if in doubt,
consult an authorized installer.
Nordväl is not responsible for any damage caused by
incorrect connection or by not following the instructions in
this manual.
(Optional)
9
English
Stop the engine and remove the fuse box lid.
Refer to your car owner’s manual to locate the fuse box and remove the lid. The
location and layout of the fuse box and the type of the fuse box depends on the
brand and type of vehicle.
1
Connect the red ACC(+) fuse to the fuse box (switched power).
Find a spare switched fuse or remove a switched fuse from the fuse box. Then place
the red ACC(+) fuse in the referred place.
2
Connect the yellow BAT fuse to the fuse box (constant power).
Find a spare constant fuse, or remove one from the fuse box. Then place the yellow
BAT fuse in the referred place.
3
Connect the black GND wire to a ground point.
Attach the GND wire to a grounding point, such as a bolt located directly on a metal
part of the vehicle frame.
Connect the USB-C cable to the Nordväl dashcam and start the engine. Check if the
dashcam turns on and keeps recording when you turn off the engine.
4
10
CONNECTING TO THE APP
11
English
Download the “Kacam” app by scanning the QR code
provided on this page, or by searching for it in the App
Store or Google Play Store.
Enable Bluetooth and GPS location, then open the
WiFi settings on your smartphone and select the
network: “DC202-2CH”. Use the default password:
“12345678” to connect.
Once connected, open the app to see live video,
change the camera settings, or download recorded
videos and photos.
App Store
Google Play Store
1
2
3
When you connect your smartphone to the dashcam for the first time,
your smartphone will ask you if you want to keep or break the WiFi
connection. Choose to keep WiFi connection.
For the app to work properly, it is important that your location settings
are enabled in your smartphone.
Note
12
APP OPTIONS
Capture image
Click on “Snapshot”
to capture an image
from the video.
Recording/Stop
Click to start or stop
recording.
Dashcam Albums
Access all saved
videos and images
here.
Audio Recording
Click to start or stop
the sound recording.
Switch Camera
Switch the display
image of the front
and rear camera.
Video Resolution
Adjust the resolution
of the recording.
General
Altri manuali per DC202-2CH
1
Indice
Altri manuali Nordval Telecamera da cruscotto
