NVision 30100VA Manuale utente
1
2
WELCOME
Thank you for purchasing our nVISION®Tire Pressure Monitoring System … the most sophisticated and
robust TPMS technology available!
This product is designed to give you years of reliable performance. If you have any questions about this product,
how to set it up or how to use, do not return it to the dealer where you bought it.
Instead, call our expert customer support team toll free at (800) 835-0129. Our tech service team is available
between the hours of 8am to 5pm CST, Monday through Friday.
NOTE: All warranties must be registered within 30 days of purchase. You can also visit
www.nVisionSafety.com to complete the warranty registration form, or call our customer support team
at the toll free number above.
3
TABLE OF CONTENTS
INITIAL INSTALLATION
Get Your TPMS Ready.............................................................................................................................................5-10
Boosting Your Signal ................................................................................................................................................. 11
Display Screen - Alerts ........................................................................................................................................19-20
Getting The Most From Your TPMS ......................................................................................................................... 21
YOUR NEW TPMS SYSTEM
Tire Safety Alerts........................................................................................................................................................ 12
TPMS Components..................................................................................................................................................... 13
Monitor Power Buttons............................................................................................................................................. 14
Navigation And Control Buttons.............................................................................................................................. 15
TPMS Warnings.......................................................................................................................................................... 16
Display Screen............................................................................................................................................................ 17
Edit Settings................................................................................................................................................................. 18
INFORMATION
Frequently Asked Questions................................................................................................................................22-27
FCC Compliance.......................................................................................................................................................... 28
Warranty Information............................................................................................................................................29-30
System Specifications............................................................................................................................................... 31
GETTING STARTED
It is important to read and understand your owner’s manual. It contains valuable information
as well as tips or suggestions for getting the most from your new TPMS System.
There are 3 basic installation steps:
1. Make sure you have the correct pressure in your tires before you install the system. It is best to install the
system in the morning when your tires are cool.
2. Turn on the monitor and scroll through the vehicle options that match your exact tire configuration.
Press the button to confirm your selection.
3. The system will ask you to install sensors one-by-one for each configuration. Locate the tire that corresponds to
the blinking tire symbol on your monitor. Screw the sensor on. When the pressure registers correctly, press .
You have established a unique electronic signature for that tire. Follow the prompts for all other tires.
Your nVISION®TPMS has a unique memory feature that allows you to store other configurations (trailers, vehicles,
motorhomes, etc.). Follow the same set up procedures for up to 4 different vehicles.
That’s it! Simple. Straight-forward. You’re now ready to roll….enjoy and be safe!!
4
5
GET YOUR TPMS READY
ACTIVATE
•Before you power up your TPMS system for the first time, you will need to attach the pivoting antenna. You will
find an antenna port in the back of the monitor. Screw the pivoting antenna into the port. Be careful not to over-
tighten the antenna.
TIP: The pivoting antenna provides flexibility and you can position to maximize signal strength from
sensors to the monitor. Also, easily pivots to fit into tight compartments in your RV.
•Insert Quick-Set™Installation Cord into the front of the monitor
for power. System will default to PSI. At initial start up, unit
will default to memory position #1
TIP: The Quick-Set™Installation Cord allows you to take the
monitor with you tire by tire for a faster and easier installation
experience.
Quick-Set™Installation Cord
(9-volt battery not included)
P
I
V
O
T
I
N
G
PSI
DEFINE MODE
When you turn your monitor on for the first time, your screen should look like
this. The “Define” Mode allows you to choose a wheel configuration that
exactly matches your vehicles and trailers.
TIP:We recommend that you program your most common driving
configurations into Memory Position 1 and 2.
Press the arrow keys to scroll through our menu of tire configurations to find
the correct configuration for your vehicle. For example, If you have a 10-wheel
motorhome scroll to this configuration
Stop on correct vehicle configuration and press to confirm selection
REMEMBER: Please take your monitor with you to each tire using the Quick-Set™Installation Cord.
NOTE:It is critical that you place the sensor on the tire that corresponds to the
flashing tire on the monitor. The system will store this specific sensor location into
memory. If you don’t put the sensor on the corresponding tire location, the pressure
will be read and reported properly, but the display will not provide the correct tire
location.
The monitor will advance to sensor installation on the tires. You will begin with the left front
tire. Please follow the diagram below when installing the sensors for your vehicle.
6
START
PSI
7
The monitor will advance to the next sensor location to install. Repeat the
same steps to complete the installation on all tires you will be monitoring.
SPARE TIRES: We recommend monitoring your spare tire so that
you know it is ready in the event of a tire failure. If you don’t want to
monitor this tire, move the curser to “NO” while this tire is blinking
and press “OK” to confirm. The system will advance to the next tire.
IMPORTANT: After you press on the last sensor in memory
position 1, monitor will advance to memory position 2 to install
your next vehicle or trailer configuration.
Press to move to Memory Position 2 and repeat the same steps
as you did for Memory Position 1 to complete your installation.
Once you have installed all of your vehicles or trailers you wish to
monitor. Use the navigational buttons and scroll to “SAVE” and
Press to exit Define Mode and enter Vehicle Position Mode.
PSI
PSI
The front left tire will begin flashing. This is where the first sensor
needs to be attached
Screw the sensor on the valve stem
The “YES” icon on the screen will be flashing. Wait for the correct
pressure to appear
Press after the correct pressure appears on the monitor
PSI
8
VEHICLE POSITION MODE
After saving your last memory position the system advances to Vehicle Position
Mode. This mode allows you to choose among the vehicles or trailers you have
stored.
TIP: In Vehicle Position Mode all defined vehicles or trailers will display
on the RIGHT side of the screen. Once positions are selected for front
and or back, the icons will display in the assigned positon.
“FRONT” icon is flashing, Press
Select the memory position you wish to monitor in the “FRONT” (The front
vehicle will be located on the LEFT hand side of the screen in normal mode)
Press to confirm
“BACK” icon is flashing, Press
Select the memory position you want to monitor in the “BACK” (The back
vehicle will be located on the RIGHT hand side of the screen in normal mode).
Press to confirm.
If you only want to monitor 1 vehicle, select “FRONT” or “Back” for
that vehicle. Then scroll to “SAVE” and Press to advance to
normal mode.
TIP: Only 1 “Front” and 1 “Back” Vehicle Configuration can be monitored
at a time.
“SAVE” icon will be flashing on the screen. Press to save your vehicle
configuration and advance to normal mode.
PSI
PSI
9
NORMAL OPERATION
Once you have completed programming your Memory Positions, your system
will enter normal operating mode. Your TPMS system will begin checking
your tires. You will see a series of check marks illuminate in the middle on
the right side of the display screen. These checks indicate that your TPMS
system is reestablishing the RF connections with each sensor and verifying
tire conditions. When all tire conditions report at normal levels, checking
will stop and your monitor will illuminate the green light.
If you have turned your monitor off, you will need to turn it on to begin the
normal operation mode. Note that from the off position, your TPMS system
will need to reestablish the RF signature for each sensor for the Memory
Positions last used. This process could take up to 5 minutes depending on the communication cycle of the sensors.
When the monitor reestablishes RF connections, the monitor will display a yellow light, to indicate that it has yet to
verify all tire conditions.
TIP: We recommend that once your system is operating, you leave it plugged in and turned on. This ensures that
you have a continuous monitoring of all tires. If your vehicle is to be parked for more than 30 days, we recommend
you turn the monitor off.
PSI
This is what your screen should
look like in Normal Mode.
10
PSI
CHANGING YOUR VEHICLE POSITION
When in Normal Mode, Press the Vehicle Position Button on the monitor.
CAUTION: Pressing the Vehicle Position Button will clear all memory
positions that have been saved in the “FRONT” or “BACK” Position
“FRONT” icon is flashing, Press
Select the memory position you wish to monitor in the “FRONT” (The front
vehicle will be located on the LEFT hand side of the screen in normal mode)
Press to confirm
“BACK” icon is flashing, Press
Select the memory position you would like to monitor in the “BACK” (The back
vehicle will be located on the RIGHT hand side of the screen in normal mode)
Press to confirm.
“SAVE” icon will be flashing on the screen. Press to save your vehicle
configuration and advance to normal mode.
When all tires report within normal tire conditions, the green light will
illuminate.
PSI
PSI
Indice
Altri manuali NVision Strumento di misura
