NXP Semiconductors MCIMX93-EVKCM Manuale utente

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

i.MX i.MX 93 EVKCM

APPLICATIONS PROCESSOR QSG

ABOUT THE i.MX 93 EVKCM

The i.MX 93 applications processor is the latest member of the

i.MX 9 family. It excels in machine learning, vision, advanced multimedia

and industrial IoT applications. Elevating edge intelligence, i.MX 93

processors are the solid foundation for products built for smart homes,

smart cities, and industrial applications.

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

FEATURES

SOM Module

• i.MX 93 applications processor

with:

–2x Arm®Cortex®-A55

–1× Arm®Cortex®-M33

–0.5 TOPS NPU

• LPDDR4X 16-bit 2GB

• eMMC 5.1, 32GB

• Power Management IC (PMIC)

• Power Measurement ADC

Base Board

• MicroSD 3.0 card slot

• Two USB 2.0 C connector

• One USB 2.0 C for Debug

• One USB C PD only

• M.2 Key-E for Wi-Fi/BT/802.15.4

• One MIPI-CSI connector

• One CAN port

• Four channels for ADC

• 6-axis IMU w/ I3C support

• I2C Expansion connector

• Two 1 Gbps Ethernet

–Port0 supports ETER

–Port1 supports TSN

• Multiple display interface:

–MIPI-DSI connector

–1x4 data lane LVDS w/ Backlight

• Audio Codec Support

• PDM MIC array support

• External RTC w/ coin cell

• 2X20 Pin Expansion I/O

GET TO KNOW THE i.MX 93 EVKCM

USB C PDUSB C PDUSB CUSB C

DebugDebug Audio JackAudio JackUSB2.0 C x2USB2.0 C x2 GbE RJ45 x2GbE RJ45 x2

II22C EXPC EXPMIPI CSIMIPI CSI

ADCADCMIPI DSIMIPI DSI LVDS / Back LightLVDS / Back Light

PDM MICPDM MIC

GPIO EXPGPIO EXP

MicroSDMicroSD

Figure 1: Top view i.MX 93 11x11 EVKCM board

CANCAN

RDPM I/FRDPM I/F

JTAGJTAG

M.2 slotM.2 slot

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

GET TO KNOW THE i.MX 93 EVKCM CONTINUED

M.2 slot (E-KEY)M.2 slot (E-KEY)

Figure 2: Back view i.MX 93 11x11 EVKCM board

GETTING STARTED

Table 1 — Kit Contents

ITEM DESCRIPTION

MCIMX93-EVKCM i.MX 93 11X11 EVKCM board

Power Supply USB C PD 45W, 5V/3A; 9V/3A; 15V/3A; 20V/2.25A supported

USB Type-C Cable USB 2.0 C Male to USB 2.0 A Male

Software Linux BSP image programmed in eMMC

Documentation Quick Start Guide

Table 2 — Customer Supplied Accessories

ITEM DESCRIPTION

IMX-MIPI-HDMI MIPI-DSI to HDMI adapter board

LVDS LCD 12.1” TFT LCD, 1280x800 RGB

RPi-CAM-MIPI IAS camera to RPi camera adapter (AR0144 sensor)

Audio HAT Audio expansion board with most of audio features

M.2 Module PN: LBES5PL2EL; Wi-Fi 6 / BT 5.2 / 802.15.4 support

Contact [email protected] to obtain a free sample

Unpack the Kit

The MCIMX93-EVKCM is shipped with the items listed in Table 1.

Prepare Accessories

The following items in Table 2 are recommended to run the

MCIMX93-EVKCM.

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

GETTING STARTED

CONTINUED

Download Software and Tools

Installation software and documentation are available

at www.nxp.com/imx93evkcm. The following are available

on the website:

Table 3 — Software and Tools

ITEM DESCRIPTION

Documentation

• Schematics, layout and Gerber files

• Quick Start Guide

• Hardware Design Guide

• i.MX 93 EVKCM Board User Manual

• Power Consumption Measurement

Software Development • Linux BSPs

Demo Images

• SCopy of the latest Linux®images that are available to program

on to the eMMC

• MCIMX93-EVKCM software can be found at nxp.com/imxsw

1Confirm Boot

Switches

The boot switches should be set to boot

from “eMMC”, SW1301[1-4] (Figure 1) are used

for boot, See table below:

2Connect USB

Debug Cable

Connect the UART cable into the port JP1401

(Figure 1). Connect the other end of the cable to

a PC acting as a host terminal. UART connections

will appear on the PC, this will be used as A55

and M33 core system debugging.

Open the terminal window (i.e., Hyper Terminal

or Tera Term), choose the right COM port number

and apply the following configuration.

• Baud rate: 115200bps

• Data bits: 8

• Parity: None

• Stop bits: 1

3Connect LVDS

panel Display

Connect an LVDS panel with J702 2x20 PIN header

through cable. Make sure jumpers on J703 (P2-P3)

and J704 (P2-P1) have been installed.

4Connect

Mouse

Connect the mouse to the USB2 C port connector

J302 through USB C OTG cable.

SETTING UP THE SYSTEM

The following will describe how to

run the pre-loaded Linux image on

the MCIMX93-EVKCM (i.MX 93).

BOOT DEVICE SW1301[1-4]

eMMC/uSDHC1 0000

5Connect

Power Supply

Connect the USB C PD power supply to J301,

then power up the board by SW301 switch.

QUICK START GUIDE

MCIMX93-EVKCM

i.MX 93 APPLICATIONS PROCESSOR

SETTING UP THE SYSTEM

CONTINUED

6Board

Boot Up

As the board boots up, you will see 4 penguins

appear in the upper left-hand corner of the

monitor, and then you will see the Linux terminal

Icon on the top left and timer on right top corner .

Congratulations, you are up and running.

J301J301

J704J704 J703J703 J702J702

J1401J1401 J302J302

JW301JW301

ADDITIONAL INFORMATION

Boot Switches

SW1301[1-4] is the boot configuration switch, the default boot device

is eMMC/uSDHC1, as shown in Table 4. If you want to try other boot

devices, you need to change the boot switches to corresponding

values as listed in Table 4.

Note: 1 = ON 0 = OFF

Indice

Altri manuali NXP Semiconductors Hardware per computer

NXP Semiconductors

NXP Semiconductors UM10569 Manuale utente

NXP Semiconductors

NXP Semiconductors AXIOM M52259DEMOCOM Manuale di installazione

NXP Semiconductors

NXP Semiconductors AN11211 Guida alla risoluzione dei problemi

NXP Semiconductors

NXP Semiconductors winbond MCX-N9 BRK Series Manuale utente

NXP Semiconductors

NXP Semiconductors JN5179 Manuale utente

NXP Semiconductors

NXP Semiconductors PN7150 Manuale utente

NXP Semiconductors

NXP Semiconductors OM13488 Manuale utente

NXP Semiconductors

NXP Semiconductors FRDM-MCXN947 Manuale utente

NXP Semiconductors

NXP Semiconductors MCIMX7SABRE Manuale utente

NXP Semiconductors

NXP Semiconductors WCT1012 Manuale utente

NXP Semiconductors

NXP Semiconductors MCUXpresso IDE MQX RTOS Guida

NXP Semiconductors

NXP Semiconductors MR-CANHUBK344 Istruzioni per l’uso

NXP Semiconductors

NXP Semiconductors i.MX 8M Mini LPDDR4 EVK Manuale utente

NXP Semiconductors

NXP Semiconductors freescale TRK-S12ZVHY64 Manuale utente

NXP Semiconductors

NXP Semiconductors i.MX 8MDQLQ Manuale utente

NXP Semiconductors

NXP Semiconductors KTTWR17510EVBUG Manuale utente

NXP Semiconductors

NXP Semiconductors AN12398 Manuale utente

NXP Semiconductors

NXP Semiconductors JN5148 Manuale utente

NXP Semiconductors

NXP Semiconductors QorIQ LS1028A Manuale utente

NXP Semiconductors

NXP Semiconductors I2C Bus AN11022 Manuale utente

NXP Semiconductors

NXP Semiconductors i.MX RT1170 Istruzioni per l'installazione e il funzionamento

NXP Semiconductors

NXP Semiconductors i.MX 8M Manuale utente

NXP Semiconductors

NXP Semiconductors S32G-VNP-EVB3 Manuale utente

NXP Semiconductors

NXP Semiconductors UM11650 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente