Oce PlotWave 750 Manuale di installazione e funzionamento
Océ PlotWave® 750
Safety guide
Copyright
© 2013, Océ
All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted in
any form or by any means without written permission from Océ.
Océ makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose.
Furthermore, Océ reserves the right to revise this publication and to make changes from time to
time in the content hereof without obligation to notify any person of such revision or changes.
Edition 2013-04 US
Contents
Chapter 1
Safety information..............................................................................................................5
Safety information (all countries)...................................................................................................................6
Chapter 2
Regulation notices............................................................................................................11
Regulation notices..........................................................................................................................................12
Chapter 3
General information.........................................................................................................17
General information.......................................................................................................................................18
Chapter 4
Miscellaneous....................................................................................................................19
Online support for your product...................................................................................................................20
Contents
3
Contents
4
Chapter 1
Safety information
Safety information (all countries)
Introduction
All the products have been tested in accordance with the strictest international safety standards.
Please read the following sections before you connect the machine to the power supply. These
sections contain important information with regard to the user safety and the prevention of
equipment problems. Make sure that you observe the safety rules hereinafter. This helps to
assure that you can work with the product/system safely. Make sure that you observe all the
precautions mentioned below.
NOTE
Depending on the context, the terms: system, machine, and equipment all will be used to
designate the Océ product for which this user documentation is applicable.
Some parts of the contents of this section may not be applicable to your product.
Please refer to the corresponding Safety Data Sheets for specific safety information. You can
download the Safety Data Sheets from the support site of your product at
"http://global.oce.com/
support/"
Warning and caution indicators (manual)
The following indicators are used in the manuals to categorize the level of the seriousness of
hazard:
WARNING
Indicates a warning concerning operations that may lead to death or injury to persons if not
performed correctly, To use the machine safely, always pay attention to these warnings.
CAUTION
Indicates a caution concerning operations that may lead to injury to persons if not performed
correctly. To use the machine safely, always pay attention to these cautions.
IMPORTANT
Indicates operational requirements and restrictions. Be sure to read these items carefully to
operate the machine correctly, and avoid damage to the machine or property.
NOTE
Indicates a clarification of an operation or contains additional explanations for a procedure.
Reading these notes is highly recommended.
NOTICE: Indicates an operation that must not be performed. Read these items carefully and make
sure not to perform the described operations
Warning and caution indicators (machine)
The following indicators are used in the machine to warn the user of possible safety risks:
Safety information (all countries)
6Chapter 1 - Safety information
CAUTION
Ignoring this caution could cause injury to skin; see also section “Action in response to
troubles”
WARNING
Whenever this label is affixed to parts of the machine that are accessible to the user, a remark
can be found in the user documentation, explaining the potential hazard for which the user is
warned or cautioned. The user is urged to consult the user documentation in order to
understand the safety risk and learn how to avoid damage or injury.
Caution Hot
Ignoring this caution could cause injury to skin: see also section "Action in re-
sponse to troubles"
Warning
Whenever this label is affixed to parts of the machine that are accessible to the
user, a remark can be found in the user documentation, explaining the potential
hazard for which the user is warned or cautioned. The user is urged to consult
the user documentation in order to understand the safety risk and learn how to
avoid damage or injury.
Disassemble and modification
WARNING
• Do not remove covers and panels which are fixed to the machine. Some machines have a
high-voltage component or a laser beam source inside that could cause an electrical shock or
blindness.
• Do not modify this machine, because this could cause a fire, electrical shock or breakdown. If
the machine contains a laser, the laser beam source could cause blindness.
• Do not carry out maintenance activities for other components and maintenance materials
than the components and materials that are mentioned in the user manual.
• Keep maintenance materials away from children.
• To avoid any risk, only properly qualified and trained service technicians are allowed to
modify the machine.
• Do not bridge or disable any safety interlock devices.
CAUTION
• Use maintenance materials or other materials for their intended purpose only.
IMPORTANT
• Do not place any liquids on the machine.
• Do not open any door while the machine starts up or runs, unless the operator panel displays
a message that asks you to open one or more doors.
• Do not bridge any mechanical or electrical circuit breakers.
Safety information (all countries)
Chapter 1 - Safety information 7
Power cord
WARNING
• Do not scratch, abrade, heat, twist, bend, place a heavy object on or cause any other damage
to the power cord. The use of a damaged power cord (exposed core wire, broken wire, for
example) could result in a fire or breakdown. If you find any of these conditions, immediately
turn OFF the power switch and unplug the power cord from the power outlet. Then call your
authorized service representative.
• Do not use an extension lead to connect the machine.
• Only use the mains connector cable that was supplied with the machine.
• Do not use any power cable other than the one provided. Never use the power cable with
any other electrical device.
Power source
WARNING
• Put the power plug directly into a wall socket that has the same configuration as the plug.
The use of an adapter leads can result in an inadequate power supply. If a proper wall outlet
is not available, ask a qualified electrician to carry out the installation.
• Do not use a multiple outlet adapter or an extension lead. Contact your authorized service
representative if an extension lead is required.
IMPORTANT
• Consult your authorized service representative before you connect other equipment to the
same wall outlet.
• Do not connect the machine to a mains voltage that differs from the value as stated on the
power marking label.
NOTE
• If connection to a different mains voltage is required, contact your authorized service
representative.
Power plug
WARNING
• For machines that are connected via a wall socket: Place the machine close to a wall socket
that is easily accessible. The power plug is intended to serve as a disconnect device.
Grounding
WARNING
• Connect the power cord to an electrical outlet (wall socket) that is equipped with a
grounding terminal.
• This equipment has not been designed for connection to an IT power system. An IT power
system is a voltage network in which the neutral wire is not connected to ground.
Safety information (all countries)
8Chapter 1 - Safety information
Installation
WARNING
• We recommend that you only connect copy-control products (or other products) that meet
(inter)national product safety and radio frequency interference standards. Only use an
attachment cable as specified by the manufacturer.
• Make sure that the machine is placed on a level, horizontal surface of sufficient strength.
• Do not place this machine on an unstable or tilted surface.
• Do not place this machine in a location that is subject to lots of vibrations and shocks.
• Do not use flammable sprays, liquids or gases near this product, because this could cause a
fire.
Ventilation
WARNING
• The machine can produce odors of exhaust air when you:
1. Use this machine in a poorly ventilated room for a long time.
2. Produce large amounts of copies or prints.
Therefore, make sure that you ventilate this room well.
• Do not place the machine in rooms which are too small and insufficiently ventilated. See the
Product Safety Data Sheet of the machine for the ventilation requirements.
IMPORTANT
• Do not block the ventilation openings of the machine.
Actions in response to troubles
WARNING
• When a piece of metal, water or any other similar foreign matter gets inside the machine,
immediately turn OFF the power switch and unplug the power cord from the power outlet.
Then call your authorized service representative.
• Immediately stop using the machine if the machine becomes excessively hot, emits smoke,
or produces unusual odors or noises. Immediately turn OFF the power switch and unplug the
power cord from the power outlet. Then call your authorized service representative.
• Stop using the machine if the machine was dropped or a cover was damaged. Immediately
turn OFF the power switch and unplug the power cord from the power outlet. Then call your
authorized service representative.
CAUTION
• Some areas inside the machine become hot. Do not touch the locations that are labeled with
the ”CAUTION HOT” symbol . Touching these areas could cause burns.
• LCD display. Do not rub, press or touch the display surface with hard material, because the
polarizer at the surface can be easily scratched. The LCD module consists of glass. Therefore,
the LCD module can damage when you drop, pinch strongly or punch the module. When
glass breaks, be careful that you do not get injured by glass pieces. Call Customer Service.
Safety information (all countries)
Chapter 1 - Safety information 9
Consumables, supplies and maintenance materials
WARNING
• Do not throw contaminated parts or parts containing toner or ink into an open flame.
• Do not leave parts containing toner or ink or contaminated parts within easy reach of
children.
CAUTION
• Always use the materials which the manufacturer recommended and which are developed
for this machine. Materials not approved by the manufacturer may result in faults in your
machine.
Moving the machine
WARNING
• Make sure that you disconnect the power cord and other cables before you move the
machine.
• Make sure that you check the documentation for the correct machine location before you
move the machine.
• Make sure that whenever the machine is moved, this is done by properly qualified people
who have received adequate instructions.
General use
WARNING
• Do not lean, lie or stand on any part of the machine, including any unit that can be pulled
outward (e.g. paper drawers).
• To prevent overbalance of the machine, only one drawer should be opened at the same time.
CAUTION
• The left cover must be closed during normal operation. This is necessary to ensure proper
operation.
• Turn off the machine before opening the fuser.
• The fuser must be closed during normal operation. The fuser may only be opened to remove
paper after a paper jam. Because of hot surfaces, the operator must always be cautious and
wear heat-protective gloves when removing material in the fuser section.
• If the printer is not equipped with the optional roll loader, the NIOSH limit value for handling
loads will be exceeded if rolls of imaging materials having a net weight of more than 7 kg/
15.4 lbs (i.e. a width of more than approx. 50 cm or 20 inches) are placed in roll position
numbers 2, 4 and 6 by only one person.
IMPORTANT
• Unplug the product when you will not use it for a long period of time.
Safety information (all countries)
10 Chapter 1 - Safety information
Altri manuali per PlotWave 750
3
Indice
Altri manuali Oce Stampante
Oce
Oce Arizona 500 Manuale utente
Oce
Oce ColorWave 600 Manuale utente
Oce
Oce ColorWave 600 Manuale utente
Oce
Oce VarioPrint 6180 Manuale utente
Oce
Oce CPS900 Manuale utente
Oce
Oce PP20D Manuale utente
Oce
Oce Arizona 600 Manuale utente
Oce
Oce VarioPrint 2090 Manuale utente
Oce
Oce TDS750 Manuale utente
Oce
Oce CS620 Pro Manuale di istruzioni
Oce
Oce TDS700 Manuale utente
Oce
Oce fx2081 Manuale utente
Oce
Oce CS 5090 Manuale utente
Oce
Oce CS7075 Manuale utente
Oce
Oce VarioPrint 6000 MICR+ series Manuale utente
Oce
Oce CS6407 Manuale utente
Oce
Oce 9400-I Manuale utente
Oce
Oce VarioLink 4550p Manuale utente
Oce
Oce Arizona 200 GT Manuale utente
Oce
Oce PlotWave 900 Manuale utente
