OHAUS TD52 Manuale utente

TD52 Indicator

Analog Option

Instruction Manual

Kit Analógico

Manual de instrucciones

Kit Analogue

Manuel d’instruction

Analog-Kit

Bedienungsanleitung

Kit Analogico

Manuale di Istruzioni

模拟量选件

使用说明书

아날로그 키트는

사용설명서

ディフェンダー5000 シリーズ

アナログキット

取扱説明書

Дополнительный интерфейс аналогового вывода для

весового терминала TD52

Руководство по эксплуатации

Manual_TD52_Analog_V1

EN-1

INTRODUCTION

This analog kit is for use with the Defender® 5000 TD52 indicators.

INTERFACE INSTALLATION

For TD52P:

1. Separate the indicator from the base by loosening load cell cable

male connector. Remove the interface option cover.

2. Break off the rib of the interface option cover as shown.

Load cell cable connector

Interface option cover

Rib

EN-2

3. Connect the 12-pin Cable Connector included with the kit to the

Main Board Connector 2. Place the ferrite in the slot of the rear

housing as shown.

4. Install the Analog Current Loop board in the indicator using 2 screws as

shown. Connect the 12 pin connector cable from the main board to the

Analog Current Loop board 12 pin connector.

5. Connect the current loop cable to the 3 pin and 3 pin connectors.

Ferrite

Main board connector

Cable

Screw

12 Pin connector

3 Pin / 3 Pin connector

Current Loop Cable

EN-3

In the direction of the arrow (from

the bottom up)

Description

V-

Negative voltage output

V+

Positive voltage output

GND

Ground

I-

Negative current output

I+

Positive current output

GND

Ground

6. Fix the cable with the cable tie to avoid falling off from the terminal

block. Put the Interface option cover back on the terminal.

For TD52XW:

1. Remove the interface option cover. Remove the 6 screws with sealed

washers. Remove the M25 hole plug as shown.

Nylon cable tie

Load cell cable connector

Screws

M25 Hole plug

EN-4

2. Rotate the rear housing down away from the front housing as

shown.

3. Connect the 12-pin Cable Connector included with the kit to the

Main Board Connector 2. Place the ferrite in the slot of the black

part as shown.

4. Disassemble the M25 Cable Gland by loosening the cap nut and removing

the rubber seal. Pass the Current Loop Output cable through the cap nut,

then spread the rubber seal and place it over the cable. Now pass the

cable through the body of the cable gland.

Main board connector 2

Ferrite

Cable

M25 Gland

Cap nut

4~20mA Current loop

output cable

EN-5

5. Install the relay board. Secure it with 2 screws to Boss Post 5 and

7 as shown.

Connect the 12 pin connector cable from the main board to the

Analog Current Loop board 12 pin connector.

6. Pass the Current Loop Output cable through the M25 hole.

Connect it to the 3 pin and 3 pin connector as shown below.

7. Put the rear housing back on the front housing. Re-install the 6

screws (Torque is 1.8N*m±0.5).

Boss post 5, 7

Screw

3 Pin / 3 Pin connector

12 Pin connector

Cable

Current Loop Cable

EN-6

8. Fasten the cap nut of M25 gland to the rear housing.

9. Warp the rubber seal onto the Current Loop Output cable and push

it to the hole.

10. Fasten the cap nut of M25 gland.

Cap nut of M25 gland

Rubber seal

EN-7

For TD52XW with reversed rear cover:

1. Remove the interface option cover. Remove the 6 screws with

sealed washer. Remove the M25 hole plug as shown.

2. Take the rear housing down from the front housing as shown.

Load cell cable connector

Screws

M25 Hole plug

EN-8

3. Connect the cable to the main board connector 2.

4. Disassemble the cable gland by loosening the cap nut and

removing the rubber seal. Pass the relay output through the cap

nut, then spread the rubber seal and place it over the cable. Now

pass the cable through the body of the cable gland.

Cable

M25 Gland

Cap nut

4~20mA Current loop

output cable

Main board connector 2

Altri manuali per TD52

Indice

Lingue:

Altri manuali OHAUS Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente