Onicon F-4600 Series Istruzioni operative

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699

www.onicon.com • [email protected]

F-4600 INLINE ULTRASONIC FLOW METER

With Optional LCD Display

Installation and Operation Guide

06-18

2020-3 / 35874

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 2

SAFETY INFORMATION

This meter was calibrated at the factory before shipment. To ensure correct use of the meter, please

read this manual thoroughly.

Regarding this Manual:

• This manual should be passed on to the end user.

• Before use, read this manual thoroughly to comprehend its contents.

• The contents of this manual may be changed without prior notice.

ONICON’s written permission.

• ONICON makes no warranty of any kind with regard to this material, including, but not

limited to, implied warranties of merchantability and suitability for a particular purpose.

• All reasonable effort has been made to ensure the accuracy of the contents of this manual.

However, if any errors are found, please inform ONICON.

• ONICON assumes no responsibilities for this product except as stated in the warranty.

• If the customer or any third party is harmed by the use of this product, ONICON assumes

no responsibility for any such harm owing to any defects in the product which were not

predictable, or for any indirect damages.

Safety Precautions:

The following general safety precautions must be observed during all phases of installation,

operation, service, and repair of this product. Failure to comply with these precautions or with

specic WARNINGS given elsewhere in this manual violates safety standards of design,

manufacture, and intended use of the product. ONICON Incorporated assumes no liability for the

customer’s failure to comply with these requirements. If this product is used in a manner not

specied in this manual, the protection provided by this product may be impaired.

The following symbols are used in this manual:

WARNING

Messages identied as “Warning” contain information regarding the personal safety of individuals

involved in the installation, operation or service of this product.

CAUTION

Messages identied as “Caution” contain information regarding potential damage to the product or

other ancillary products.

IMPORTANT NOTE

Messages identied as “Important Note” contain information critical to the proper operation of the

product.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 3

TABLE OF CONTENTS

1.0 INTRODUCTION ...................................................................................................... 5

1.1 PURPOSE OF THIS GUIDE ........................................................................... 5

1.2 TYPICAL F-4600 FLOW METER .................................................................. 5

1.3 STANDARD FEATURES AND SPECIFICATIONS........................................ 5

1.4 WORKING ENVIRONMENT ......................................................................... 7

1.5 SERIAL NUMBER .......................................................................................... 7

2.0 UNPACKING ............................................................................................................. 7

2.1 CHECKING THAT YOU HAVE RECEIVED EVERYTHING .......................... 7

3.0 INSTALLATION........................................................................................................ 8

3.1 SITE SELECTION ........................................................................................... 8

3.2 INSTALLING THE FLOW SENSOR .............................................................. 8

3.3 REMOTE MOUNTING THE CALCULATOR ENCLOSURE ........................ 12

3.4 POWER AND SIGNAL WIRING CONNECTIONS ...................................... 13

4.0 F-4600 FLOW START UP AND COMMISSIONING ............................................. 14

4.1 START UP ..................................................................................................... 14

4.1.1 Operating Mode .............................................................................. 15

4.1.2 Additional Display Pages ............................................................... 16

4.2 COMMISSIONING....................................................................................... 17

4.2.1 Commissioning Following Initial Power-up.................................. 17

5.0 DIAGNOSTIC FUNCTIONS ................................................................................... 21

6.0 BACNET MS/TP..................................................................................................... 22

6.1 BACNET®OBJECT TYPES .......................................................................... 22

6.2 PROTOCOL IMPLEMENTATION STATEMENT ........................................ 22

6.3 DEVICE OBJECT .......................................................................................... 23

6.4 ANALOG INPUT(S) ..................................................................................... 24

6.5 ANALOG VALUE(S) .................................................................................... 25

6.6 BINARY VALUE(S) ...................................................................................... 26

6.7 MULTI STATE VALUE.................................................................................. 27

6.8 TREND LOG MULTIPLE............................................................................... 28

7.0 MODBUS®........................................................................................................ 29

7.1 MODBUS®MEMORY MAP ......................................................................... 33

7.2 DIAGNOSTIC FUNCTION CODE................................................................. 33

7.3 REPORT SLAVE ID FUNCTION CODE........................................................ 34

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 4

8.0 AUXILIARY INPUTS AND OUTPUTS ................................................................... 35

8.1 DETERMINING AUXILIARY INPUT & OUTPUT CONFIGURATION........ 35

8.2 AUXILIARY INPUTS .................................................................................... 35

8.3 AUXILIARY OUTPUTS ................................................................................ 36

8.3.1 Pulse Outputs.................................................................................. 36

8.4 ANALOG OUTPUTS .................................................................................... 37

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 5

SECTION 1.0: INTRODUCTION

1.1 PURPOSE OF THIS GUIDE

The purpose of this guide is to provide installation and commissioning procedures, and basic

operating and servicing instructions for the ONICON F-4600 ow meter with optional LCD

display.

1.3 STANDARD FEATURES AND SPECIFICATIONS

• Detachable enclosure with alphanumeric display and user interface

• Three 2-wire signal ports can be congured as pulse input or outputs. One of the ports can

be congured as an analog output.

WARNING

Only qualied service personnel should attempt to install or service this product. Serious injury

may result from the improper installation or use of this product.

1.2 TYPICAL F-4600 FLOW METER

The F-4600 inline ow meter utilizes direct path wetted ultrasonic transducers for measuring

the volumetric ow and temperature of liquids in a wide variety of applications. The meter is

provided with a detachable enclosure with a built-in user interface/display.

POWER

24 V AC/DC

Input Power

Input and Output

Signals and

BACnet / MODBUS

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 6

NOTE: Specications subject to change without notice

GENERAL SPECIFICATIONS

ACCURACY

FLOW

± 1% of reading over 25:1 turndown

± 2% of reading over 100:1 turndown

Repeatability: ≤ ± 0.2%

OVERALL FLOW RANGE

500:1 turndown

SENSING METHOD

Direct beam path wetted ultrasonic sensors utilizing

differential transit time velocity measurement

METER SIZES (Nominal diameter in inches)

½, ¾, 1, 1¼, 1½, 2 and 2½

PIPING SYSTEM CONNECTIONS

Male NPT threads

2½” meter provided with ANSI Class 150 raised face

anges

Optional PN16 or ANSI Class 300 raised face anges

FLUID TEMPERATURE RANGE

32°F to 250°F

AMBIENT TEMPERATURE RANGE

-13°F to 131°F

MAXIMUM OPERATING PRESSURE

400 PSI

PRESSURE DROP

Less than 1 psi at 4 ft/sec, decreasing at lower velocities

POWER SUPPLY REQUIREMENTS

20-28V AC/DC, 50/60 Hz, 5 VA maximum

PULSE INPUTS, OUTPUTS, and ANALOG OUTPUT

The three 2-wire signal ports can be congured as pulse inputs or

outputs. One of the ports can be congured as an analog output.

Isolated totalizing pulse inputs for use with sinking open

collector or dry contact outputs

Input rating: 30 VDC, 10 mA maximum

Pulse duration: 50 ms minimum

Isolated totalizing solid state contact closure pulse outputs may

be programmed for energy, volume, alarm indication or coil

indication (MODBUS RTU only)

Contact ratings: 50 mA, 30 V

Contact pulse duration: 50, 100, 500 or 1000 ms (500ms

default)

Analog 4-20 mA, 0-5 V or 0-10 V output for ow rate or

temperature

NETWORK CONNECTION

Isolated RS485 serial interface

COMMUNICATION PROTOCOLS

BACnet MS/TP per ASHRAE Standard 135.1: 2009

MODBUSR RTU

NETWORK CONFIGURATION & ADDRESSING

Baud Rates: 4800, 9600, 19200, 38400, 76800, or 115200

Device Address Range: 1 – 127 (1 - 247 MODBUS)

Device Instance Range: 1 – 4,194,303 (BACnet only)

Parity: None, Even, Odd (MODBUS RTU only)

APPROVALS

FCC: Part 15, Subpart B

Conforms to ANSI/NSF 61 & 372

BTL Certied to ASHRAE 135:2009

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 7

1.4 WORKING ENVIRONMENT

The F-4600 with optional LCD display was designed for installation and use indoors or outdoors

in protected spaces, or in residential, commercial and light industrial environments that are free

of corrosive liquids and fumes, temperature extremes and excess vibration.

The operating ambient air temperature range is -13°F to 131°F. The electrical power should be

relatively clean, free of excess high frequency noise and large voltage transients.

1.5 SERIAL NUMBER

Serial Number

The serial number of your F-4600 is located on the side of the enclosure. The serial number

is a unique identier for the product. Please have this number available when contacting

ONICON for assistance.

SECTION 2.0: UNPACKING

The F-4600 is generally shipped in one package unless optional hardware or equipment is ordered.

Notify the freight carrier and ONICON if any items are damaged in transit.

2.1 CHECKING THAT YOU HAVE RECEIVED EVERYTHING

The following items have been provided with your F-4600 Flow Meter:

Two line size process connection meter couplings* with male NPT threads and sealing gaskets

(shipped attached to meter)

One F-4600 Meter Installation and Operation Guide

One F-4600 Meter Certicate of Calibration

One Remote Mount Bracket

Please notify ONICON if any of these items are missing.

*NOTE: The 2½” version of the meter is provided with anges.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 8

SECTION 3.0: INSTALLATION

The F-4600 Flow Meter should be installed by experienced plumbers, electricians, and others with

related knowledge and experience in the heating, cooling, and uid metering elds. ONICON technical

support personnel are available via telephone or e-mail to provide technical assistance before, during

and after installation. On-site eld engineering, installation, and service are also available at an

additional cost. The installer should use good trade practices and must adhere to all state and local

building, or other, applicable codes.

Before you begin, clean the external surfaces of all pipes at the installation site so that it is free of

debris, foreign matter, solids, leak inhibitors, and chemically aggressive substances. Flush the entire

system so that it is free of ux, solder, pipe and tube cuttings and any other free moving debris.

3.1 SITE SELECTION

Careful attention to the site selection for the meter will help the installers with the initial

installation, reduce start-up problems, and make future maintenance easier. For example, do not

install the meter where it will be difcult for personnel to perform periodic maintenance. When

selecting a site, consider the criteria under Section 1.4: WORKING ENVIRONMENT, as well as

the information below.

The following limitations apply to the installation of the meter:

• The ow meter must be correctly oriented with respect to the direction of ow in the pipe.

Meters installed with reversed ow will not function.

• The F-4600 is provided with a 4.9 ft (1.5 m) cable for the detachable enclosure. Do not alter

this cable length. Doing so will void the calibration and may invalidate the warranty.

• The maximum operating pressure for the ow meter is 400 psi.

• At uid temperatures above 212°F, the enclosure should be remote mounted.

• Do not install the meter in close proximity to strong sources of electromagnetic interference

(e.g. electric motors, VFD’s, uorescent light xtures, etc.)

3.2 INSTALLING THE FLOW SENSOR

Before you install the meter, the entire piping system should be ushed and free of debris. Please

refer to the diagrams on the following page when selecting the installation location. Upstream

straight unobstructed pipe requirements vary considerably based on nature of the upstream

obstructions. As a general rule, ONICON recommends a minimum of 10 diameters of straight

unobstructed pipe whenever possible; keeping in mind that it is always recommended that the

meter be located with as much straight pipe upstream as possible. Recommended minimum

straight run requirements are provided on the following page.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 9

A. This is a recommended position for the ow sensor.

B. Avoid installation locations where air can become trapped in the piping system.

C. This is an acceptable installation location for closed loop pressurized systems.

D. Do not install the sensor downstream of modulating valves or partially open valves.

Fully open isolation valves (e.g. ball valves) are OK.

E. Do not install the ow sensor at the inlet of a pump. To prevent cavitation, the

minimum operating pressure at the inlet of the meter must always exceed the pressure

drop across the meter. Refer to Appendix A-3 for calculating pressure the drop at

different ow rates.

F. Avoid installing the meter downstream of multiple bends out of plane with each other

where there are less than 10 diameters of straight unobstructed pipe between bends.

D & E

Flow Direction

STRAIGHT RUN REQUIREMENTS

Upstream Obstruction

Minimum Upstream Straight Run Required (Pipe Diameters)

Meter Size

0.5 - 1.0" 1.25 - 2.5"

Single Elbow 0 0

Expander / Reducer 0 0

Coil, Upstream 3 3

Isolation Valve, 2 Position 3 5

Control Valve 10 15

Notes:

1 Straight run is based on use of manufacturer provided couplings

2 Avoid the following obstructions where possible: Modulating valves, pump discharge, multiple

elbows out of plane.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-4600 With LCD Flow Meter Manual 06/18 - 2020-3 / 35874 Page 10

Flow Direction The sensor port is always on

the downstream end of meter.

Retaining Nut SealCoupling

The ow sensor is installed with threaded meter couplings and at sealing gaskets as shown

below. Orient the sensor body by aligning the ow direction arrow with the direction of ow

in the pipe.

Model Meter Size Min.

Compression

Min. Turn Past

Initial Contact

Degrees of

Rotation

F-4600-050 ½” 30% 1/2 180°

F-4600-340 ¾” 30% 1/3 120°

F-4600-341 ¾” 30% 1/3 120°

F-4600-010 1” 30% 2/5 140°

F-4600-011 1” 30% 2/5 140°

F-4600-130 1¼” 30% 2/5 140°

F-4600-150 1½” 30% 4/9 160°

F-4600-200 2” 30% 1/2 180°

INSTALLING METER COUPLINGS

• Inspect seating surfaces on the meter’s body and tail piece prior to assembly. Surfaces should be

clean and free of any burs or markings.

• Install the gasket in tail piece. Thread union onto meter’s body, by hand, until gasket and mating

surfaces make rst contact. Mark coupling nut and tail piece.

• Place a corresponding mark on the coupling nut, # of degrees (based on table above) counter

clockwise. Hold meter body while rotating coupling nut clockwise until marks line up. DO NOT

over-tighten.

• Repeat process on opposite side of ow meter body.

NOTE: Torque setting is not an accurate means of gaging compression on gasket due to the lack of

resilience in the gasket material.

• Pressurize system and check for leaks. If any leak is present, DO NOT over-tighten. Relieve pressure

and loosen coupling nuts. Remove and inspect the gasket for damage. Repeat installation process.

Altri manuali per F-4600 Series

Indice

Altri manuali Onicon Strumento di misura

Onicon

Onicon F-4400 Manuale utente

Onicon

Onicon Vortex Flow Meter F-2200 Series Istruzioni operative

Onicon

Onicon F-4600 Series Istruzioni operative

Onicon

Onicon FT-3000 Series Manuale utente

Onicon

Onicon F-5200 Istruzioni operative

Onicon

Onicon D-100 Manuale utente

Onicon

Onicon SYSTEM-30 Istruzioni operative

Onicon

Onicon SYSTEM-20 Istruzioni operative

Onicon

Onicon SYSTEM-20 Istruzioni operative

Onicon

Onicon F-1000 SERIES Istruzioni operative

Onicon

Onicon SeaMetrics EX90 Manuale utente

Onicon

Onicon System-10 BTU Meter Istruzioni operative

Onicon

Onicon System-10 BTU Meter Manuale utente

Onicon

Onicon F-3100 Series Istruzioni per il montaggio

Onicon

Onicon SYSTEM-30 Istruzioni operative

Onicon

Onicon F-4300 Istruzioni di montaggio

Onicon

Onicon System-10 BTU Meter Istruzioni operative

Onicon

Onicon F-1500 Series Istruzioni operative

Onicon

Onicon F-1100 Series Istruzioni operative

Onicon

Onicon System-10 BTU Meter Manuale utente

Onicon

Onicon Fox Thermal FT1 Manuale utente

Onicon

Onicon F-5000 Istruzioni operative

Onicon

Onicon System-10 BTU Meter Istruzioni operative

Onicon

Onicon F-1000 SERIES Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente