ooznest WorkBee CNC Manuale utente
WorkBee CNC
Power Supply Assembly Instructions
WorkBee CNC 1
Table of Contents
1.0 Getting Started 3
1.1 Check Product Contents 4
1.2 Notes on Assembly 4
2.0 Power Supply Assembly 5
2.1 Output 6
2.1.1 Securing XT60-Male Outputs ........................................................ 6
2.1.2 Inserting LED-Volt-Meter .............................................................. 7
2.2 Input 8
2.2.1 IEC-Inlet Wires ........................................................................... 8
2.2.2 Attaching IEC-Inlet...................................................................... 9
2.3 Connecting PSU-Cover 10
2.3.1 Connecting Wires ...................................................................... 10
2.3.2 Attaching PSU-Cover ................................................................. 12
2.3.3 Testing .................................................................................... 13
3.0 Appendix 14
3.1 Appendix A - Kit Contents 15
WorkBee CNC Getting Started 2
1.0 Getting
Started
WorkBee CNC Getting Started 3
1.1 Check Product Contents
When you receive your kit, the first thing you should do is check the contents against the
list in Appendix A. The majority of the parts will be separated into boxes that correspond
to the subsections in this manual. Additional spare small parts will be included. If anything
is missing or damaged (or if you have any other problems) please contact us at
1.2 Notes on Assembly
This manual has been written for the construction of a 750 x 750mm screw driven version
of the WorkBee. If you have a different version everything is exactly the same, with the
exception of longer V-Slot extrusions and wire routing.
It is recommended that you read through the whole manual before beginning the build in
order to get a full picture of the assembly process. Before beginning each step, make
sure you have studied the diagram and have the required parts in front of you. A PDF
version of the manual is available on our website and this will allow you to zoom in on the
diagrams if needed.
Be very careful to not over tighten the nuts and bolts on the plastic parts, otherwise they
may crack. Everything should easily fit together, and so if it isn’t, take a step back and
re-read the instructions.
Assembly of this kit involves the use of electricity and therefore you should take appro-
priate precautions to ensure you are assembling the kit in a safe manner. When following
wiring diagrams, double check that everything is connected correctly. Before carrying out
any work on the electrics make sure that the machine is switched off.
The polarity is indicated by the color of the wire, not by the color of the connectors at each
end. For the AC IEC input, the live wire is brown, neutral blue, and earth is green and yel-
low. For the DC Wiring of the machine a positive wire is red, negative is black, and earth
is green and yellow.
WorkBee CNC Power Supply Assembly 4
2.0 Power
Supply
Assembly
WorkBee CNC Power Supply Assembly 5
2.1 Output
2.1.1 Securing XT60-Male Outputs
A. Insert the XT60-Male connectors into the provided inset on the PSU-Cover. it should
sit flush with the front of the PSU-Cover.
B. Secure the XT-Male connector using 2 x Plastite-Screw-M2.5-8mm through the holes
provided on the securing tab as seen on the internal view. When initially placing the
screw, it is helpful to hold each screw in place using tweezers or long nose pliers.
WorkBee CNC Power Supply Assembly 6
2.1.2 Inserting LED-Volt-Meter
A. Gently push the LED-Volt-Meter into the provided gap on the top of the PSU Cover.
The wires on the LED-Volt-Meter should be oriented to the front of the PSU-Cover.
WorkBee CNC Power Supply Assembly 7
2.2 Input
2.2.1 IEC-Inlet Wires
A. Attach the receptacle end of the IEC-Inlet-Live-Wire, IEC-Inlet-Neutral-Wire & IEC-
Inlet-Earth-Wire to their respective terminal tabs on the IEC-Inlet, as seen in the
above image.
WorkBee CNC Power Supply Assembly 8
2.2.2 Attaching IEC-Inlet
A. Secure the assembled IEC-Inlet to the PSU-Cover using 2 x Plastite-Screw-M3-8mm.
Ensure the switch is on the right hand side.
Altri manuali per WorkBee CNC
2
Indice
Altri manuali ooznest Sistema di controllo
