Overland Storage NEO 4000e Manuale utente

IMPORTANT: Overland Storage requires that all NEO

Series parts be removed and replaced by an Overland

Storage authorized service provider. Improper installation may

result in damage which voids existing warranties.

This document describes how to remove and replace the

Power Supply Receiver of a NEO 4000Elibrary from

Overland Storage.

WARNING: The GUI touch screen does not completely

shut off NEO SERIES system power. To reduce the risk

of electric shock or damage, unplug both power cords.

CAUTION: To prevent damage, do not leave a power

supply receiver bay empty during operation of the unit.

Unpacking the Spare

Carefully unpack and verify that you have all the parts:

•NEO 4000E power supply receiver

•Five M3x6mm flathead screws

•Six M4x8mm flathead screws

•One 6/32x3/8 panhead Phillips screw

•Five 6/32x1/4 flathead screws

•These instructions

NOTE: Except for the DB-15 jack screws, discard all the old

screws and use the new screws provided.

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent Electrostatic

Discharge (ESD), observe standard ESD precautions.

1. If the library is operational:

a. Using the GUI or the application software, remove

any cartridges from the drives to prevent damage.

b. Exit the application software and, if necessary,

stop the software services.

c. Use the GUI to remove all the magazines.

IMPORTANT: If the library is non-operational, the

doors can be manually opened by pushing a stiff

wire through the front panel release holes (Figure 1).

Figure 1. Manual Door Release Locations

2. Shut down the library as follows:

a. If necessary, use the GUI to power down the library.

b. Turn the power supply switches to OFF (O).

c. Remove the power cords.

d. Remove all data cables.

e. Also, to reduce weight, we recommend removing the

drive assemblies.

3. If XpressChannel is installed, release it by loosening

the four captive screws on the back side and

unplugging the DB-15 plug.

WARNING: It is recommended that a mechanical

lifter (or at least two people) be used to prevent

injury during rack installation or removal.

4. Using a mechanical lifter (or two people), remove the

unit from the rack and place on a secure ESD surface.

5. Remove the two key top covers:

a. Remove the two screws securing the primary

cover and set the cover aside.

b. Remove the four screws securing the power

supply cover and set the cover aside.

NEO®4000E

Spare Power Supply Receiver

Remove & Replace Instructions

Overview & Notes

NEO-9196

Prepare the Library

NEO-0155

Manual Release

6. If necessary, remove the XpressChannel cover plate

(Figure 2):

a. Remove drives #2 and #4 to access the cover inner

mounting screws.

b. Remove the two screws located inside drive bays #2

and #4.

c. Remove the screw on the top.

d. Remove the two screws outside next the power

supplies securing the cover.

e. Set the XpressChannel cover aside.

7. Remove the power supplies:

a. Remove the mounting screw securing the power

supply locking bracket.

b. Pushing down on the latches, use the handles to pull

the power supplies out of the receiver.

Figure 2. Removing the XpressChannel Cover

1. Working through the opening behind the right

magazine tracks, remove the two 22-pin main power

harness connectors:

a. Press the release on the left side of the left

connector and pull firmly.

b. Repeat Step a for the right connector.

2. Remove all four of the 4-pin drive power connectors

located above and to the right of the 22-pin sockets.

3. Remove and retain the two jack screws that secure

the DB-15 connector (located above the power supplies).

4. Move the DB-15 cable up and toward the chassis

center so as not to interfere with receiver removal.

5. Outside the back of the library, remove the five

mounting screws while supporting the receiver.

6. Carefully remove the receiver through the opening in

the top of the library (Figure 3).

You may have to tip it toward the rear to release the

power sockets at the bottom. Figure 3. Removing the Old Receiver

1. Install the new Power Supply Receiver:

a. Insert it into the opening at the top of the library.

b. From the rear, supporting the receiver, secure it

with five new 6/32x1/4 flathead screws.

2. Connect the receiver wiring inside (Figure 4):

a. Push the lower drive bay main power harness

plug into the right 22-pin connector until it latches.

b. Insert the two lower drive bay drive power plugs

in the lower two 4-pin connectors.

c. Push the upper drive bay main power harness

plug into the left 22-pin connector until it latches.

d. Insert the two upper drive bay drive power plugs

in the next two 4-pin connectors. Figure 4. Receiver Rear Connectors

NEO-9198

M3x6mm

4x8mm

Locking Bracket

Remove the Old Receiver

NEO-9197

DB-15

Connector

Power

Connectors

Install the New Receiver

Upper

Connectors

Drive Bay

Lower

Connectors

Drive Bay

3. Reposition the DB-15 connector to its chassis hole

and secure it with the two retained jack screws.

4. Verify all the wiring is correct:

a. Visually check that none of the wiring is looped or

sticking out into the path taken by the shuttle.

b. Check that the ferrite boxes on the wiring

harnesses are push as close as possible to plugs

connected to the receiver.

CAUTION: Care must be taken to ensure that the

wiring is not positioned so that it comes into contact

with the shuttle during normal operation.

5. If removed, reinstall the XpressChannel cover:

a. Position the XpressChannel cover over the

opening.

b. Install a new M3x6mm flathead screw in the top.

c. Install two new M4x8mm flathead screws inside

drive bays #2 and #4.

d. Install two new M4x8mm flathead screws outside

next the power supplies, securing the cover.

e. Carefully reinsert the #2 and #4 drive assemblies.

6. Reinstall the top covers:

a. Using four new M3x6mm screws, reinstall the

power supply receiver cover.

b. Using two new M4x8mm screws, reinstall the front

chassis cover.

7. Reinstall the power supplies:

a. Carefully insert each power supply and push it

firmly against the rear backplane until it seats.

b. Using the new 6/32x3/8 mounting screw, reinstall

the locking bracket to secure power supplies.

8. Reinstall the library in the rack:

a. Using a mechanical lifter (or two people), carefully

slide the unit in the same rack position.

b. If removed, reinstall the drive assemblies.

c. If used, reconnect the XpressChannel.

d. Reconnect the data cables.

e. Reconnect the power cords.

f. Toggle the power supply switches to ON.

g. Press anywhere on the GUI touchscreen power on

the module.

9. Using the replacement part box, return the old part to

Overland Storage.

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com, or call

1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).

Altri manuali per NEO 4000e

Altri manuali Overland Storage Magazzinaggio

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage REO Series Manuale utente

Overland Storage

Overland Storage NEO S-Series Manuale utente

Overland Storage

Overland Storage LTO-4 Manuale utente

Overland Storage

Overland Storage NEO 4000e Manuale utente

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage SnapScale X2 Node Manuale utente

Overland Storage

Overland Storage REO Series Manuale utente

Overland Storage

Overland Storage SnapServer XSR 120 Manuale utente

Overland Storage

Overland Storage NEO 8000 Manuale utente

Overland Storage

Overland Storage SnapServer Manuale di servizio

Overland Storage

Overland Storage ARCvault 12 Manuale utente

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage NEOxl 40 Manuale utente

Overland Storage

Overland Storage ARCvault Series Manuale utente

Overland Storage

Overland Storage NEO Series Manuale utente

Overland Storage

Overland Storage Neo Series Library Manuale utente

Overland Storage

Overland Storage NEO S-Series Manuale utente

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage NEO XL Series Manuale utente

Overland Storage

Overland Storage NEO 2000e Manuale utente

Overland Storage

Overland Storage ULTAMUS Manuale

Overland Storage

Overland Storage Snap Server 210 Manuale utente

Overland Storage

Overland Storage SnapSAN S3000 Manuale di servizio

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente