Overland Storage NEO Series Manuale utente

IMPORTANT: Overland Storage requires that all NEO

Series parts be removed and replaced by an Overland

Storage authorized service provider. Improper installation may

result in damage which voids existing warranties.

This document describes how to remove and replace the

Shuttle Track assembly in a NEO 4000Elibrary from

Overland Storage.

WARNING: The GUI touch screen does not completely

shut off NEO SERIES system power. To reduce the risk

of electric shock or damage, unplug both power cords.

Unpacking the Spare

Carefully unpack and verify that you have all the parts:

•NEO 4000EShuttle Track assembly

•Eight (8) M3x20mm panhead Phillips screws

•Eight (8) M3 cup washers

•These instructions

Electrostatic Discharge Information

A discharge of static electricity can damage micro-circuitry

or static-sensitive devices. To help prevent Electrostatic

Discharge (ESD), observe standard ESD precautions.

1. If the library is operational:

a. Using the Graphical User Interface (GUI) or the

application software, remove any cartridges from

the drives to prevent damage.

b. Exit the application software and, if necessary,

stop the software services.

c. Use the GUI to remove all the magazines.

IMPORTANT: If the library is non-operational, the

doors can be manually opened by pushing a stiff

wire against the mechanical releases (Figure 1) directly

behind the front panel to remove the magazines.

Figure 1. Manual Door Release Locations

2. Power off the library as follows:

a. Use the GUI to power down the library.

b. Turn the power supply switches to OFF (O).

c. Remove the power cord.

3. Remove all external host cables.

4. Also, to reduce weight, we recommend removing the

drive assemblies at this time.

WARNING: It is recommended that a mechanical

lifter (or at least two people) be used to prevent

injury during rack installation or removal.

5. Using a mechanical lifter (or two people), remove the

unit from the rack and place on a secure ESD surface.

6. Remove and retain the two screws securing the front

top cover.

7. Lift and remove the front top cover, and set aside.

NEO ®4000E

Spare Shuttle Track Assembly

Remove & Replace Instructions

Overview & Notes

NEO-0169

Preparing the Library

NEO-0155

Manual Release

1. Remove the shuttle:

a. By hand, turn the motor/track coupler until the

track section is at a 45° or larger angle (Figure 2).

b. With one hand supporting the top of the shuttle,

grasp the shuttle base and carefully slide the

shuttle off the track.

Figure 2. Top View of Track Showing Movable Section

c. Without twisting the shuttle flex cable, set the

shuttle assembly (with the PCB up) on the top

edge of the unit (Figure 3).

Figure 3. Set the Shuttle Aside; PCB Up

2. Disconnect the track flex cable from the track plate

PCB (Figure 4):

Figure 4. Cable Connections on Flex Cable Card

3. Remove the eight M3x20mm screws and washers

(Figure 5) securing the two Z-Axis assemblies to the

track plate.

Figure 5. Remove the Z-Axis Screws

4. Raise the front Z-Axis about 1/2 inch by turning the

motor coupler clockwise (Figure 6).

Figure 6. Turn Front Z-Axis Motor Coupler

5. Raise the rear Z-Axis about one inch by turning the

pulley gear clockwise (Figure 7).

Figure 7. Turn Rear Z-Axis Pulley Gear

Removing the Old Assembly

NEO-0150

Motor/Track Coupler Shuttle

Assembly

Flex Cable PCB

Remove Screws

Turn Coupler

Turn Gear

6. Verify that the Z-Axis has cleared the track plate

alignment pins (Figure 8).

7. Carefully remove the old track and set it aside.

IMPORTANT: Check for loose hardware on the chassis

floor. Remove it before continuing.

Figure 8. Shuttle Track Z-Axis Alignment Pins

1. Position the new track assembly on the chassis floor.

2. Attach the rear Z-Axis:

a. Lower the rear Z-Axis bracket onto the alignment

pins on the track plate by turning the pulley gear

counterclockwise.

b. Align both sides of the rear Z-Axis base to the edges

of the track plate (Figure 9).

Figure 9. Align Rear Z-Axis Bracket & Tighten Screws in Order

c. Using four new M3x20mm screws and M3 cup

washers, secure the rear Z-Axis to the track plate

using around 6 lbs of torque.

Tighten the screws in the order shown in Figure 9.

Be sure the cup washer is positioned correctly

(Figure 10).

Figure 10. Screw and Cup Washer Assembly

3. Attach the front Z-Axis:

a. Lower the front Z-Axis bracket by turning the

motor coupler counterclockwise until it contacts the

track plate.

b. Align both sides of the front Z-Axis base to the edges

of the track plate (Figure 11).

Figure 11. Align Front Z-Axis Bracket & Tighten Screws in Order

c. Using four new M3x20mm screws and M3 cup

washers, secure the front Z-Axis to the track plate

using around 6 lbs of torque.

Tighten the screws in the order shown in Figure 11.

4. Reconnect the track flex cable to the track assembly

PCB (Figure 12).

Figure 12. Cable Connections on Flex Cable Card

Alignment Pins

Installing the New Assembly

Align Z-Axis Base 1

to Track Edges

Screw head

Cup Washer

(Cup Up)

Align Z-Axis Base

2to Track Edges

Track Track

Flex Cable PCB

5. Reinstall the shuttle:

a. By hand, turn the track motor/track coupler until

it is at a 45° or greater angle (Figure 13).

Figure 13. Top View of Track Showing Movable Section

b. Carefully lift the shuttle and position it at the open

end of the track, checking that there are NO twists

in the flex cable (Figure 14).

Figure 14. Flex Cable Position Around Shuttle Spooler

NOTE:

The open side of the shuttle should be on the left.

c. Slide the shuttle onto the track making sure the

shuttle flex cable wraps around the spooler correctly.

Power On Library

Before returning the unit to the rack, verify that it works.

1. For SCSI systems, verify the terminators are still in

place.

2. Plug in the power cord.

3. Turn the power supply switch to ON (|).

4. Tap the GUI to power on the library.

5. Observe the POST process to verify the shuttle

assembly installation:

•Watch the shuttle assembly and track movement.

•Make sure that nothing interferes with the cable

assembly through its full range of motion.

NOTE: If problems occur, contact Overland Storage

Technical Support.

Run Diagnostics

Test the library’s operational mechanisms to make sure

they are running and operating properly.

NOTE: If you do receive errors, note them and contact

Overland Storage Technical Support.

1. From the touch-screen GUI, press Menu >

Diagnostics > Cartridge Cycle.

2. Run the Cartridge Cycle:

a. Press Start.

b. Allow the cycle to run at least 5 minutes.

c. Press Stop.

3. Using the Move Media function, load and unload a

cartridge from each drive.

4. Power off the library as follows:

a. Use the GUI to power down the library.

b. Turn the power supply switches to OFF (O).

c. Remove the power cord.

Reinstall the Library

1. Slide the front top cover tabs into their slots and

gently set the cover into place.

2. Reinstall the two retained cover screws.

1. Using a mechanical lifter (or two people), reinstall the

library into the rack.

2. Reinstall any removed drive assemblies.

3. Reattach all external host cables.

Return Old Track Plate

1. Place removed parts in the replacement part box.

2. Follow directions included in the box for returning

parts to Overland Storage.

NEO-0150

Motor/Track Coupler Shuttle

Assembly

Power On and Test the Library

Additional Help

You can get additional technical support on the Internet at http://support.overlandstorage.com, or call

1-877-654-3429 (toll-free U.S. & Canada), +44 (0) 118-9898050 (Europe), or +1 (858) 571-5555 Option 5 (International).

Altri manuali per NEO Series

Questo manuale è adatto per i seguenti modelli

Altri manuali Overland Storage Magazzinaggio

Overland Storage

Overland Storage NEO 8000E Manuale utente

Overland Storage

Overland Storage XchangeNOW ARCvault Series Manuale utente

Overland Storage

Overland Storage PowerLoader Manuale utente

Overland Storage

Overland Storage NEO 2000e Manuale elenco delle parti

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage NEO 8000 Manuale utente

Overland Storage

Overland Storage NEO Series Manuale utente

Overland Storage

Overland Storage NEO Series Manuale utente

Overland Storage

Overland Storage NEO 8000E Manuale utente

Overland Storage

Overland Storage ARCvault Series Manuale utente

Overland Storage

Overland Storage NEO 8000E Manuale utente

Overland Storage

Overland Storage REO 9000 Manuale utente

Overland Storage

Overland Storage NEO 8000 Manuale utente

Overland Storage

Overland Storage SnapServer DX2 Manuale utente

Overland Storage

Overland Storage NEO S-Series Manuale utente

Overland Storage

Overland Storage NEO 2000e Manuale utente

Overland Storage

Overland Storage NEO XL Series Manuale utente

Overland Storage

Overland Storage NEO 2000e Manuale utente

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage SnapServer DX1 Manuale utente

Overland Storage

Overland Storage PowerLoader Manuale utente

Overland Storage

Overland Storage SnapServer XSD 40 Manuale utente

Overland Storage

Overland Storage ARCvault Series Manuale utente

Overland Storage

Overland Storage SnapServer DX1 Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente