PC Partner BSB871S Manuale utente

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital

device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable

protection against harmful interference in a residential installation. This equipment

generates,usesand can radiate radiofrequencyenergyand,ifnot installed and usedin

accordancewithinstructionscontainedinthismanual,maycauseharmfulinterference

toradio andtelevisioncommunications. However,there isnoguarantee thatinterference

willnotoccurin a particular installation.

Ifthisequipment does cause harmful interference toradioortelevisionreception,which

canbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotryto

correctthe interference byone or moreof the followingmeasures:

- REORIENTORRELOCATETHERECEIVINGANTENNA

- INCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDTHERECEIVER

- CONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROM

THATOFTHERECEIVER

- CONSULTTHEDEALERORANEXPERIENCEDAUDIO/TELEVISION

TECHNICIAN

NOTE: Connecting this device to peripheral devices that do not comply with Class B

requirements, or using an unshielded peripheral data cable, could also result

in harmful interference to radio or television reception.

Theuser is cautionedthatanychangesor modifications notexpresslyapproved

by the party responsible for compliance could void the user’s authority to

operate this equipment.

To ensure that the use of this product does not contribute to interference, it is

necessarytouseshieldedI/O cables.

reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility for errors

or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the

information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their respective owners.

Technical Reference Booklet

Table of Contents

HARDWARE CONFIGURATION .............................................................. 3

Key Features ............................................................................................... 3

Motherboard Layout (Model Code No. - 35887100XX) ............................... 5

Jumper Settings .......................................................................................... 6

CPU Speed Selection............................................................................ 6

JP1 - Host Bus Speed Select ................................................................ 6

JP4 - CMOS Clear.................................................................................. 6

JP15 - Firm Ware Hub Top Block Memory Protect ................................ 7

JP16 - Infrared Connector Power Select ............................................... 7

JP17 - Speaker Out Select..................................................................... 7

JP29 - KB Voltage Select ....................................................................... 7

JP34 - PCI Sound Enable...................................................................... 7

JP36 - AC97 Codec Select .................................................................... 7

Memory Configuration ................................................................................. 8

To install DIMMs .......................................................................................... 8

Installing the Processor .............................................................................. 9

BIOS SETUP ............................................................................................... 1 0

Starting Setup .............................................................................................. 10

Main Menu ................................................................................................... 10

Standard CMOS Features ........................................................................... 12

Advanced BIOS Features ............................................................................ 14

Advanced Chipset Features........................................................................ 14

Integrated Peripherals ................................................................................ 14

Power Management Setup.......................................................................... 14

PNP/PCI Configurations ............................................................................. 14

Set Supervisor/User Password .................................................................. 14

Flash Update Procedure ............................................................................. 16

HARDWARE CONFIGURATION

This motherboard is based on the Intel® 810 chipset that is the first generation

IntegratedGraphics chipset designedfor the Intel® Celeron®PPGA Processor.

The graphics accelerator architecture consists of dedicated multi-media

engines executing in parallel to deliver high performance 2D, 3D, and motion

compensation video capabilities. In additional of AC’97 allows to use software

configurable AC’97 audio and modem coder/decoders via AMR slot instead of

the traditional ISA devices. Features on-board include LPC, Ultra DMA33/66,

PCI bus master IDE, PCI Ver 2.2 compliance, USB, VRM 8.2 compliance, PCI

sound system(optional).

Key Features

Processor

• Full support for the Intel® Celeron® PPGA processors using PGA370

Socket.

• Supports66MHzand100MHzbusspeedIntel® Celeron® PPGAprocessor

and future PPGA processor

CPU Speed Jumperless

• No jumper is needed to set for various speed of CPU.

VRM (Voltage Regulator Modules) on Board

• Flexible motherboard design with on-board VRM 8.2, easy to upgrade

with Intel’s® Future Overdrive® processors.

Cache

• Processor built-in L2 128K cache.

System Memory

• Up to 256MB or 512MB using 128M bit technology.

• 100MHz Bus speed.

PC97/98

• PC97/98 ready.

Expansion Slots

• 1 Audio Modem Riser (AMR).

•4 PCI bus master slots (ver. 2.2 compliant).

On-Board I/O

• Two PCI fast IDE ports supporting up to 4 ATA2, Ultra DMA 33 or Ultra

DMA66(82801AA only) IDE HDDs, CD-Roms, ZIP devices and LS-120

drives as boot drive.

• Supports bus master IDE, PIO mode 4 (up to 16M bytes/sec) and Ultra

DMA 33/66 (up to 66M bytes/sec) transfer.

• One ECP/EPP parallel port (via a header).

• Two 16550-compatible UART serial ports.

• One floppy port supporting two FDDs of 360KB, 720KB, 1.2MB, 1.44MB

or 2.88MB formated capacity.

Hardware Setup

Technical Reference Booklet

• Two USB ports (via a header).

• Keyboard port (factory option for PS/2 type).

• PS/2 mouse port (via a header).

• Infrared (IrDA) support (via a header).

• One Line / Speaker out, one Mic in, one Line in and MIDI / Gameport (via

a header).

• One VGA connector (via a header).

System BIOS

• 4M Intel Firm Ware Hub with security feature.

• Supporting PnP, APM, ATAPI and Windows® 95/98.

• Auto detects and supports LBA hard disks with formatted capacities

over8.4GB.

• Easily upgradable by end-user.

Plug-and-Play

• Supports plug-and-play specification 1.1.

• Plug-and-play for DOS, Windows® 3.X, Windows® 95 as well as

Windows® 98.

• Fully steerable PCI interrupts.

Power Management

• SupportsSMM, APM and ACPI.

• Break switch for instant suspend/resume on system operation.

• Energy star “Green PC” compliant .

• Supports WAKE-ON-LAN (WOL).

• Supports Wake on Ring for External Modem.

On board Sound Sub-system (optional)

•Integrated AC97 controller with standard AC97 CODEC.

Crystal PCI AC97 sound controller (optional)

• Crystal CS4280/81 AC97 Audio controller.

• Direct sound and sound Blaster Compatible.

• Full Duplex, Crystal 3D Enhancement, Software wavetable.

Integrated Graphics Controller

•3D Hyper Pipelined Architecture.

•Full 2D H/W Acceleration.

•Motion Video Acceleration.

•Integrated 24bit 230MHz RAMDAC.

•Up to 1600x1200 in 8bit Color at 85Hz Refresh.

•H/W Motion Compensation Assistance for S/W MPEG2 Decode.

•Software DVD at 30fps.

Display Cache Interface (82810-DC100 only)

•32bit data interface.

•100MHzSDRAM interface.

Hardware Setup

Motherboard Layout (Model Code No. - 35887100XX)

The following diagrams show the relative positions of the jumpers, connectors,

major components and memory banks on the motherboard.

Warning:

All connectors on board are labeled Pin “1” at one conner. Ribbon

cables should always be connected with the red stripe on the Pin

“1” side of the connector.

CN26 - WOL

CN30 CN29

Chassis Fan

Technical Reference Booklet

Jumper Settings

This chapter explains how to configure the motherboard’s hardware. Before

using your computer, make sure all jumpers and DRAM modules are set

correctly. Refer to this chapter whenever in doubt.

CPU Speed Selection

In this motherboard, jumperless feature is implemented such that no jumper is required to

be set for different type of CPU installed.

Notice:

1. Be sure to save the CMOS setting when exit the CMOS.

2. Celeron PGA370 CPU is frequency multiplier locked, no CPU speed change will

be seen even if the frequency multiplier setting in CMOS setup is changed.

JP1 - Host Bus Speed Select

JP1 HCLK

(Close)* Auto*

(Open) 100MHz

JP2, JP3 - PCI3 Master Assign

JP2 JP3 Assign

(1-2)* (1-2)* for PCI Slot4*

(2-3) (2-3) for On Board PCI Sound Chip

Warning:If you use On Board PCI Sound, Bus master Card can not use

on PCI Slot4.

JP4 - CMOS Clear

JP4 Selection

(1-2)* Normal*

(2-3) CMOS Clear

Close Open

JP34

JP16

JP17

JP4

* = Default setting.

JP1

JP29

JP2

JP3 1

JP15

JP36

Close Open

* =Default setting

Hardware Setup

JP29 - KB Voltage Select

JP29 Select

(1-2)* Baby AT Power(VCC)*

(2-3) ATXPower(5VSB)

Warning:

Before handling the motherboard from its original package, please

ensure that there is no static electricity on your body. Otherwise it

may cause damage to the integrated circuits on the motherboard.

JP17 - Speaker Out Select

JP17 Select

(1-2) To Outside Speaker

(2-3)* Normal*

JP16 - Infrared Connector Power Select

JP16 Select

(1-2) Powered by +5V

(2-3)* Powered by +5V Stand by*

JP15 - Firm Ware Hub Top Block Memory Protect

JP15 Selection

(Open)* Locked*

(Close) Unlocked

JP34 - PCI Sound Enable

JP34 Select

(1-2)* Enable*

(2-3) Disable

JP36 - AC97 Codec Select

JP36 Select

(1-2)* Enable*

(2-3) Disable

Technical Reference Booklet

Memory Configuration

You can install DIMM memory in the motherboard DIMM sockets. The board

has DIMM sockets arranged as banks 1, and 2. You can install DIMMs in any of

the two banks, and use different size DIMMs in different banks. The BIOS

detects the size and type of installed memory.

To install DIMMs

1. Turn off all peripheral devices connected to the computer. Turn off the

computer.

2. Remove the computer cover and locate the DIMM sockets.

3. Holding the DIMM by the edges, remove it from its antistatic package.

4. Make sure the clips at either end of the socket are pushed away from the

socket.

5. Position the DIMM above the socket. Align the two small notches in the

bottom edge of the DIMM with the keys in the socket.

6. Insert the bottom edge of the DIMM into the socket.

7. When the DIMM is seated, push down on the top edge of the DIMM until the

retaining clips at the ends of the socket snap into place. Make sure the

clips are firmly in place.

8. Replace the computer cover.

Clip

Clip DIMM

DIMM Socket

Notch

Warning:

Turn system power off before installing and removing any device,

otherwise you’ll cause the system damage.

Hardware Setup

Installing the Processor

For easy installation of the CPU, it is recommended that you remove all

Cards in PCI slots first.

• Unpack the CPU and identify the pin 1 corner of the CPU.

• Match pin 1 of the CPU with pin 1 of the CPU socket. The pin 1 corner of

the CPU socket is designated by a small triangle printed on the

motherboard.

• Carefully insert the CPU into the CPU socket and move the metal arm

downward to replace it in its original position. Change any jumper settings

as detailed in the manual.

The small circle marked on the top of the CPU designates the pin 1 corner.

If a heat sink is attached and covers the top of the CPU, identify the pin 1

corner by turningthe CPU over. Locate the small gold finger that extends

from one corner of the large central square portion of the CPU. The gold

finger points towards pin 1, which is also uniquely identified by a square pad.

Positioning the CPU incorrectly in the socket can permanently damage

the CPU and the computer when you turn on the system.

Warning:

There is a fan attached the CPU to prevent the overheating, please

ensure that the fan can operate. Otherwise the CPU can overheat

and cause damage to both CPU and motherboard.

Caution

Please check your computer

chassis if it is carrying any metal

mounting post at this location.

Remove the mounting post or

add insulation to the post before

putting in the motherboard.

Technical Reference Booklet

BIOSSETUP

This chapter discusses Award’s Setup Program built into the ROM BIOS. The

Setup Program allows users to modify the basic system configuration. This

special information is then stored in battery-backed RAM, which retains the

setup information when the power is turned off.

Starting Setup

The Award BIOS is immediately activated when you turn on the computer. The

BIOS reads the system information contained in the CMOS and begins the

process of checking out the system and configuring it. When it finishes, the

BIOS will seek an operating system on one of the disks and then launch and

turn control over to the operating system .

While the BIOS is in control, the Setup Program can be activated:

1. By pressing <Del> immediately after switching the system on, or

2. By pressing the <Del> key when the following message appears briefly at

the bottom of the screen during the POST (Power On Self Test )

Press DEL to enter SETUP

If the message disappears before you can respond and you still wish to enter

Setup, restart the system to try again by turning it OFF then ON or pressing the

“RESET” button on the system case. You may also restart by simultaneously

pressing the <Ctrl>, <Alt>, and <Delete> keys. If you do not press the keys at

the correct time and the system does not reset, an error message will be

displayed and you will again be asked to ...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

Getting Help

Press F1 to pop up a small help window that describes the appropriate keys to

use and the possible selections for the highlighted item. To exit the Help

Window press <Esc> or the F1 key again.

In Case of Problems

If, after making and saving system changes with the Setup Program, you

discover that your computer does not reset, use the Award BIOS defaults to

override the CMOS settings.

Main Menu

Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear

on the screen. The Main Menu allows you to select from various setup functions

and two exit choices. Use the arrow keys to select among the items and press

<Enter> to accept and enter the sub-menu.

Indice

Altri manuali PC Partner Scheda madre

PC Partner

PC Partner 35884903 Manuale per l'uso e la cura

PC Partner

PC Partner MB520N Manuale per l'uso e la cura

PC Partner

PC Partner 35C96200 Series Manuale utente

PC Partner

PC Partner 35887201 Series Manuale utente

PC Partner

PC Partner 357757 Series Manuale per l'uso e la cura

PC Partner

PC Partner LXA826D Manuale utente

PC Partner

PC Partner 35886300 Series Manuale utente

PC Partner

PC Partner 35889700 Series Manuale utente

PC Partner

PC Partner VIB814DSE Manuale utente

PC Partner

PC Partner 35891700 Series Manuale per l'uso e la cura

PC Partner

PC Partner 35C96701 Series Manuale per l'uso e la cura

PC Partner

PC Partner SAPPHIRE PURE PERFORMANCE II Manuale utente

PC Partner

PC Partner 35880301 Manuale per l'uso e la cura

PC Partner

PC Partner S650MS4-260 Manuale utente

PC Partner

PC Partner 35891900 Series Manuale utente

PC Partner

PC Partner P4X266AS4-258X Manuale utente

PC Partner

PC Partner SAPPHIRE PURE PERFORMANCE Manuale utente

PC Partner

PC Partner MB600N Manuale di installazione e funzionamento

PC Partner

PC Partner 35880101 Manuale per l'uso e la cura

PC Partner

PC Partner 35-AA33 0 Series Manuale utente

PC Partner

PC Partner 845AS4-281 Manuale utente

PC Partner

PC Partner P4X266EAS4-258E Manuale utente

PC Partner

PC Partner 35-AA14-X0-XX Manuale per l'uso e la cura

PC Partner

PC Partner 35892900 Series Manuale per l'uso e la cura

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente