PC Partner LXA826D Manuale utente

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device,pursuanttoPart15ofFCCRules.Theselimitsaredesignedtoprovidereasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with instructions contained in this manual, may cause harmful interference

to radio and television communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- REORIENTORRELOCATETHERECEIVINGANTENNA

- INCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDTHERECEIVER

- CONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROM

THATOFTHERECEIVER

- CONSULTTHEDEALERORANEXPERIENCEDAUDIO/TELEVISIONTECHNICIAN

NOTE: Connecting this device to peripheral devices that do not comply with Class B

requirements, or using an unshielded peripheral data cable, could also result

in harmful interference to radio or television reception.

The user is cautioned that any changes or modifications not expressly approved

by the party responsible for compliance could void the user’s authority to

operate this equipment.

To ensure that the use of this product does not contribute to interference, it is

necessary to use shielded I/O cables.

reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility for errors

or omissions is assumed. Neither is any liability assumed for damages resulting from the use of the

information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their respective owners.

Technical Reference Booklet

Table of Contents

HARDWARE CONFIGURATION .............................................................. 3

Key Features ............................................................................................... 3

Motherboard Layout (Model Code No. - 35880201/35880202) ................. 5

Hardware Setting......................................................................................... 6

CPU Speed Selection............................................................................ 6

JP4 - CMOS Clear.................................................................................. 6

JP16 - Keyboard Power on Password Clear ........................................ 6

JP8, JP23 - PNP BIOS Program Voltage ............................................... 6

Keyboard Password Power on ................................................................... 7

Installation ................................................................................................... 7

Installing the Retention Mechanism...................................................... 7

Installing the Processor ........................................................................ 7

Setting the Processor Speed ................................................................ 8

Installing the DIMMs .............................................................................. 8

BIOS SETUP ............................................................................................... 9

Starting Setup .............................................................................................. 9

Main Menu ................................................................................................... 9

Standard CMOS Setup ................................................................................ 11

BIOS Features Setup................................................................................... 12

Chipset Features Setup .............................................................................. 13

Power Management Setup.......................................................................... 13

PNP/PCI Configuration Setup ..................................................................... 13

Integrated Peripherals ................................................................................ 13

Supervisor/User Passward Setting ............................................................ 13

Flash Update Procedure ............................................................................. 14

HARDWARE CONFIGURATION

The Pentium® II Micro ATX motherboard is based on the Intel® 440EX/440LX

Chipset. The chipset is a highly integrated solution for a cost-effective and

compact motherboard. The motherboard supports SDRAM and 3.3V EDO.

Features on-board include super-I/O, Ultra DMA33, PCI bus master IDE, AGP

Ver1.0, PCIVer2.1 compliant, USB,VRM 8.1compliant, ECC (440LX ver.only),

compliant, Micro ATX specification 1.0 compliant, LM79 hardware

monitoring(optional).This motherboard is ready for the PC98 requirements.

Key Features

Processor

• Full support for the Intel® Pentium® II and Intel® Celeron® Processors

using Slot 1connector.

• Support 66MHz bus speed including all Pentium II and Celeron

processors operating from 233MHz to 333MHz.

CPU Speed Jumperless

• No jumper is needed to set for various speed of CPU.

VRM (Voltage Regulator Modules) on Board

• Flexible motherboard design with on-board VRM 8.1, easy to upgrade

with Intel’s future overdrive processors.

Cache

• Pentium II Processor built-in L2 cache .

System Memory

• A total of two 168-pin DIMM sockets (EDO / Synchronous DRAM ).

• Supports Extended Data Out (EDO) DRAM at 50ns and 60ns Speeds.

• Support Symmetrical and Asymmetrical DRAM addressing.

• Memory size upto 256MBytes for SynchronousDRAM or 512MBytes for

EDODRAM.

• Support single density DIMMs of 1M, 2M, 4M ,8M and 16M depth (x64 or

x72).

• Support double density DIMMs of 2M, 4M, 8M, 16M and 32M depth (x64

or x72).

• Support Error Checking and Correction (ECC) using parity DRAM

modules(440LX ver. only).

• Banks of different DRAM types and depths can be mixed.

• Support for Auto Detection of Memory Type.

PC97/98

• PC97/98 ready.

Hardware Setup

Technical Reference Booklet

On-Board I/O

•On board two PCI fast IDE ports supporting up to 4 ATA, ATA2 and Ultra

DMA33 IDE HDDs, CD-ROMs, ZIP drives and LS-120 drives as boot

drive.

•Support Bus Master IDE and PIO mode 4 (up to 22M bytes/sec) and

Ultra DMA33 (up to 33M bytes/sec) transfer.

•One ECP/EPP parallel port

•Two 16550 Compatible UART serial ports .

•One floppy port, Supports two FDD of 360KB, 720KB, 1.2MB , 1.44MB

and 2.88MB capacity.

•Two USB port.

•PS/2 keyboard port .

•PS/2 mouse port .

• Infrared (IrDA) support (via a header).

System BIOS

•1M or 2M Flash BIOS supporting PnP, APM, ATAPI and Windows 95

•Jumper selection for 5V or 12V Flash memory voltage.

•Auto detects and supports LBA hard disks with capacities over 8.4GB.

• Easily upgradable by end-user.

Plug-and-Play

• Supports plug and play specification 1.1a

•Plug and play for DOS, Windows 3.X as well as Windows 95.

•Fully steerable PCI interrupts.

Power Management

• SupportSMM, APMand ACPI.

•Break switch for instant suspend/resume on system operations.

•Energy star “Green PC” complaint.

•Support Micro ATX specification 1.0 .

• Supports WAKE-ON-LAN (WOL).

• Supports Wake on Ring for internal(External) Modem.

Expansion Slots

• Supports SB-LINK Port for creative Sound interface Card.

• 1 AGP slot (ver. 1.0, 1x/2x mode supported).

• 2 PCI bus master slots (rev. 2.1 compliant, with 1 PCI slot sharing with

1 ISA slot).

•2 ISA slots (1 ISA slot shares with 1 PCI slot).

System monitoring (optional)

• LM79/75 or Compatibles hardware monitoring circuitry is supported,

provides voltages, temperature, fan speeds monitoring etc..

Keyboard Password Turn ON

• Special feature for system security.

Hardware Setup

Motherboard Layout (Model Code No. - 35880201/35880202)

The following diagrams show the relative positions of the jumpers, connectors,

major components and banks on the motherboard.

11 1 1111

Technical Reference Booklet

JP4 - CMOS Clear

JP4 Selection

1-2* Normal*

2-3 CMOS Clear

JP16 - Keyboard Power on Password Clear

JP16 Selection

1-2* Normal*

2-3 Clear Keyboard Power on Password

Hardware Setting

This chapter explains how to configure the motherboard’s hardware. Before

using your computer, make sure all jumpers and DRAM modules are set

correctly. Refer to this chapter whenever in doubt.

JP8

JP23

JP16

JP4

CPU Speed Selection

In this motherboard, jumperless feature is implemented such that no jumper is required to

be set for different type of CPU installed.

The CPU speed is set in “CPU Speed Setting” of CMOS Setup.

Notice:

1. Be sure to save the CMOS setting when exit the CMOS.

2. When the system is turned on the first time or the CPU is changed, a Pentium

II-133 will be recognised and a warning message of “CPU has been changed”

willappear.Please enter the CMOS setup menu to reconfigure theCPUspeed.

Close Open

JP4

JP14 - Keyboard Power Select

JP14 Selection

1-2 Powered by +5V

2-3* Powered by +5V Standby

(Allows Keyboard Power ON)

Keyboard Password Power ON

This motherboard provides a special security feature of keyboard password

power on. The feature is enabled in integrated peripherals menu of CMOS

setup. There are two modes of operations.

(1) single Key Turn on - if you set a single key password, the system will

turn on immediately after you press the password key.

(2) Keys Sequence Turn on - if you set a password with more than one

character, ie. a combination of keys, the system will turn on after you

press the password key sequence and then a <enter>.

Please notice that the power button will have no function if the keyboard

passwordpoweron featureisenabled.

JP8, JP23 - BIOS Program Voltage

JP8 JP23 Selection

1-2 1-2 INTEL

1-2 2-3 MX

2-3 2-3 ATMEL/SST

JP8 & JP23 are pre-installed in the factory. They should NOT be altered by

the users.

* =Default setting

Close Open

Hardware Setup

Technical Reference Booklet

Latches

RetainingPins

Retention

Mechanism

Support Bar

Installation

Installing the Retention Mechanism

To install the retention mechanism, follow these steps:

1. Locate Slot 1 and the four attachment studs on the motherboard.

2. To position the mechanism, orient it as shown in figure. The tab on the

connector fits into a notch in the base of the mechanism. When properly

seated, the base of the mechanism is flush with the motherboard.

3. Finger tighten all four captive nuts to make sure they start correctly on the

threads of the attachment studs.

4. To secure the mechanism, tighten the captive nuts.

Installing the Processor

To install the processor, follow these steps:

1. Insert the processor in the retention mechanism.

2. Press down on the processor until it is firmly seated in the Slot 1 connector

and the latches on the processor lock into place.

3. Slide the top heatsink support bar onto the retaining pins of the support’s

base as shown in figure.

Setting the Processor Speed

After you install the processor and install the motherboard, set the processor

speed by CMOS setup. Change the CPU speed as detailed in the manual.

Slot1

Captive Nuts

Studs

Tab

Retention Mechanism

Installing the DIMMs

1. Turn off all peripheral devices connected to the computer. Turn off the

computer.

2. Remove the computer cover and locate the DIMM sockets.

3. Holding the DIMM by the edges, remove it from its antistatic package.

4. Make sure the clips at either end of the socket are pushed away from the

socket.

5. Position the DIMM above the socket. Align the two small notches in the

bottom edge of the DIMM with the keys in the socket.

6. Insert the bottom edge of the DIMM into the socket.

7. When the DIMM is seated, push down on the top edge of the DIMM until the

retaining clips at the ends of the socket snap into place. Make sure the

clips are firmly in place.

8. Replace the computer cover.

9. If you installed a DIMM with ECC memory, start the computer and use the

ECC Configuration feature in Setup to enable the use of ECC.

Clip

Clip DIMM

DIMM Socket

Notch

Hardware Setup

Technical Reference Booklet

BIOSSETUP

This chapter discusses Award’s Setup Program built into the ROM BIOS. The Setup

Program allows users to modify the basic system configuration. This special information

is then stored in battery-backed RAM, which retains the setup information when the

power is turned off.

Starting Setup

The Award BIOS is immediately activated when you turn on the computer. The BIOS

reads the system information contained in the CMOS and begins the process of

checking out the system and configuring it. When it finishes, the BIOS will seek an

operating system on one of the disks and then launch and turn control over to the

operating system .

While the BIOS is in control, the Setup Program can be activated :

1. By pressing <Del> immediately after switching the system on, or

2. By pressing the <Del> key when the following message appears briefly at the

bottom of the screen during the POST (Power On Self Test )

Press DEL to enter SETUP

If the message disappears before you can respond and you still wish to enter Setup,

restart the system to try again by turning it OFF then ON or pressing the “RESET” button

on the system case. You may also restart by simultaneously pressing the <Ctrl>, <Alt>,

and <Delete> keys . If you do not press the keys at the correct time and the system does

not reset, an error message will be displayed and you will again be asked to ...

PRESS F1 TO CONTINUE, DEL TO ENTER SETUP

Getting Help

Press F1 to pop up a small help window that describes the appropriate keys to use and

the possible selections for the highlighted item. To exit the Help Window press <Esc> or

the F1 key again.

In Case of Problems

If, after making and saving system changes with the Setup Program, you discover that

your computer does not reset, use the Award BIOS defaults to override the CMOS

settings.

Main Menu

Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the

screen. The Main Menu allows you to select from various setup functions and two exit

choices. Use the arrow keys to select among the items and press <Enter> to accept and

enter the sub-menu.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PC Partner Scheda madre

PC Partner

PC Partner VIB814DSE Manuale utente

PC Partner

PC Partner 35886300 Series Manuale utente

PC Partner

PC Partner P4X266EAS4-258E Manuale utente

PC Partner

PC Partner 35-AA33 0 Series Manuale utente

PC Partner

PC Partner 35887201 Series Manuale utente

PC Partner

PC Partner 35880101 Manuale per l'uso e la cura

PC Partner

PC Partner 35891900 Series Manuale utente

PC Partner

PC Partner 35-AA09 0 Series Manuale per l'uso e la cura

PC Partner

PC Partner 35889700 Series Manuale utente

PC Partner

PC Partner 35C92000 Series Manuale utente

PC Partner

PC Partner 35C96801 Series Manuale per l'uso e la cura

PC Partner

PC Partner 35833101 Manuale utente

PC Partner

PC Partner P4M266MS4-181M Manuale utente

PC Partner

PC Partner 35884903 Manuale per l'uso e la cura

PC Partner

PC Partner P4X266EAS4-284E Manuale utente

PC Partner

PC Partner 35891700 Series Manuale per l'uso e la cura

PC Partner

PC Partner SAPPHIRE PURE PERFORMANCE II Manuale utente

PC Partner

PC Partner SAPPHIRE PURE PERFORMANCE Manuale utente

PC Partner

PC Partner 35-AA14-X0-XX Manuale per l'uso e la cura

PC Partner

PC Partner MB520N Manuale per l'uso e la cura

PC Partner

PC Partner S650MS4-260 Manuale utente

PC Partner

PC Partner 35880301 Manuale per l'uso e la cura

PC Partner

PC Partner 35C96200 Series Manuale utente

PC Partner

PC Partner 357757 Series Manuale per l'uso e la cura

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente