PDW TPMS Manuale utente
TIRE PRESSURE MONITORING SYSTEM
All copyright reserved by PDW International © 2019
Notice
*
Do not watch the device when driving.
*
This product is for passenger cars only.
*
Ensure to read through the user manual completely and fully
understand the contents before use.
*
It is recommended that a tyre professional install this product.
*
This product is an effective to tool to continuously monitor the tyre
inflation point; this unit may not be effective during sudden deflation
or accidents.
*
Do not use in conjunction with tyre foam filling products.
*
The monitor does not require constant observation. When there is
abnormal tyre pressure or temperature, the display will automatically
alarm with both a visual and audio cue.
*Ensure that the in car display does not distract while driving.
*
This manual covers internal and external sensors.
TPMS Brief Introduction
This product includes four sensors and one in-car display. The
sensor will detect the tyre pressure and temperature. Continuously
transmitting the tyre pressure and temperature data, in wireless
mode to the in-car display. When abnormal activity is detected, an
alarm will be activated to alert the driver of the issue (both by an
audio and visual alert).
Content
1. Display Installation---------------------------------------------------------------1
2. Sensor Installation---------------------------------------------------------------1
2.1
External Sensor Installation----------------------------------------------- 1
2.2
Internal Sensor Installation-------------------------------------------------2
3. Pressure, Temperature, Battery Display----------------------------------- 3
4. Alarm-------------------------------------------------------------------------------- 3
5. Setting The Unit------------------------------------------------------------------ 4
6. Pairing-------------------------------------------------------------------------------5
6.1
Automatic Lightning Pairing For Internal Sensors
(Quick Pairing)-----------------------------------------------------------------5
6.2
Manual Pairing For Internal Sensors (Standard Pairing)-----------5
6.3
External Sensor Pairing-------------------------------------------------7
7. Threshold Adjustment---------------------------------------------------------- 7
8. Technology Parameters------------------------------------------------------- 9
9. Product Content---------------------------------------------------------------- 10
10. Guarantee---------------------------------------------------------------------- 11
1
1
a
1.Display Installation
1.
The unit may be affixed to the dashboard of the car, using the 3M
adhesive tape supplied. Ensure that the display does not impair
driving vision.
2.
First time system boot, hold down the “OK” and “ ” button
simultaneously for 3 seconds, until the LCD display comes to life.
It is not required to shut down the unit in daily use.The unit will be in
sleep mode in 15 minutes if there isn't any vibration detected.
3.
To shut down, hold down the “OK” and “ ” button simultaneous-
ly for 3 seconds, on release you will hear a “beep” sound. This
will indicate that the system is shutdown. This should only be
required when resetting the unit.
2.
Sensor Installation
2.1
External SensorInstall
a.Ensure that the sensor is used in the corresponding position
displayed on the sensor. LF- Left Front RF – Right Front LR – Left
Rear RR – Right Rear
External Sensor Install
b. Install the anti-theft screw
c. Install the sensor
d. Tighten the sensor with nut provided nut wrench in reverse
direction.
e. Check to ensure no leakage and sensor is securely fastened.
d
4
c
3
b
2
2
a
b
c
d
External Sensor Battery Replacement Step
1.
Remove the outside cover.
2.
Remove the old battery.
3.
Install the new battery using battery type CR1632.
4.
Replace the outside cover
2.2
Internal Sensor Install (This step should only
be done by a tyre professional)
e
f
g
h
a.
Remove the tyre from the wheel.
b.
Remove the old valve from the wheel.
c.
Ensure the valve hole area is clean.
d.
Install the internal sensor
e.
Lock the screw of the sensor on the outside of the wheel.
f.
Product should be as fitted shown.
g.
Replace tyre, check for leakage and balance the wheel.
h.
Reinstall on car.
3
Remarks:
1.
Ensure the sensor calibration position when positioning sensor on
the car.
2.
After installation, ensure to check for leakage from the valve area.
3.
Once installed as above, you are now ready to enjoy the added
safety of your TPMS unit.
4.
This product is a plug-and-play device. Everything has been
preset already. Only when it is necessary, can you move to the
contents below.
3.
Pressure, Temperature, Voltage Display
To switch between the battery voltage, tyre pressure/ temperature
display, short press the “SET” button.
4.
Alarm
Alarm will sound when the monitor senses a safety issue. The
corresponding tyre position symbol will flash, accompanied by a
“beeping” sound.
4
P1
P4
P2
5.
Setting The Unit
Setting the unit of pressure display
1. Long press “SET” button under the main interface as shown in the
below interface.
2. Click “SET” button again into the below interface.
3. Click “SET” button again into the below interface.
P3
4. Click “SET” button again into the unit of pressure interface, as
below.
Press “OK” button during this interface, either Bar or Psi will flash.
Click “SET” button again to switch from the Bar or Psi pressure unit.
Press “OK” button to confirm, then click the button，twice to exit.
5
6.
Pairing
*Only required if choosing to change sensor position or singular
replacement.
6.1
Automatic Lightning Pairing For Internal Sensors
(Quick Pairing)
The Internal Sensor has automatic lightning pairing function. Each
sensor is free to be installed in any tyre. Tyre position will be
automatically defined on the display within 2-5 minutes
(speed >20km/h).
After 5 times of automatic pairing, the wheel position is locked & the
automatic pairing function is inactivated for saving battery power.
At the time when the wheel position is changed, press the “OK”
button for 5 seconds until a beep is heard. Thus, the automatic
lightning pairing function will be re-activated.
6.2
Manual Pairing For Internal Sensors(Standard Pairing)
a.
In the pressure display interface (pictured), hold the “SET” button
for 3 seconds and release when a “beep” is heard, the LCD will
display the flashing left front wheel.
b.
While the left front tyre symbol is flashing, press the “OK” button
to show the ID learning mode. The ID number of the left front tyre
sensor LCD is displayed as shown.
P1
6
c.
In the pressure display interface (pictured), hold the “SET” button
for 3 seconds and release when a “beep” is heard, the LCD will
display the flashing left front wheel.
d.
Click the “OK” button to enter the learning mode (In the example
below, we select left front tyre).
e.
Setup the sensors：Inflate or deflate corresponding tyre
(left front in the above example)
f.
When the display receives a learning signal from the tyre sensor, it
will prompt a beep and will show the latest sensor ID number. This
will show that this sensor position is successfully set up.
7
The system will automatically jump to the next sensor position. The
order of sensor set up is FL—FR—RR—RL
g.
When all tyres are set up, the display will stop at the rear left
position and show its ID. Click “ ” button to exit the setup
procedure.
Note: During every step you can click the button to cancel the
current operation.
6.3
External Sensor Pairing
For an external sensor, follow the 6.2 steps to select the wheel on
the monitor.Reinstall the sensor when the monitor shows the
corresponding wheel position.
7.
Threshold Adjustment
1.
In the pressure display interface, click the “SET” button for 3
seconds until a “beep” is heard and the LCD displays the left front
wheel.(Figure 1)
2.
Click “SET” button to choose the tyre position.(Figure 2)
P1
P2
Altri manuali per TPMS
1
Indice
