Pentair AUTOTROL LOGIX 742 Manuale utente

Logix™ No-Salt Detector (Chlorine Generator)

Installation Instructions (North American)

The Logix 742 and 762 controls feature a check salt light

which indicates when the end user should add salt to the

regenerant tank. The Logix control can also be

programmed to produce a low level of chlorine to

chlorinate the resin bed during regeneration. Potassium

chloride or sodium chloride may be used. Installing this

feature is simple.

Step 1

Remove the Logix control from the valve and disconnect

power.

Step 2

Insert the small connector of the no-salt detector cord to

the back of the Logix control. See Figure 1.

Step 3

Remove the existing refill controller and ball from the valve

and replace it with the no-salt detector refill flow control.

See the illustrations to the right for the location of the refill

controller.

Step 4

Insert the large white connector of the no-salt detector

cord to the end of the refill flow control. Press it in firmly to

make sure there is good contact.

Step 5

Reconnect power to the Logix control and reinstall the

control to the valve.

Step 6 742/762 Programming

To activate the chlorine generator/salt detector on the

742/762, follow these instructions:

1. Power up the 742/762 control.

2. Press the UP and DOWN buttons

simultaneously for 5 seconds to enter Level

II programming.

3. Scroll to parameter P13 using the DOWN button.

The controller will display the previous setting.

4. Press the SET button. The display will begin to

flash.

5. Set to one of the following settings as desired:

0 = chlorine generator/salt detector disabled.

1 = salt detector enabled.

2 = chlorine generator with salt detector

enabled.

6. Once the correct setting above is selected, press

SET to enter your setting. After 30 seconds the

controller will return to normal operation mode.

Back of Logix Control

255 Valve Identification

Refill Controller

Injector and Cap

No-Salt Detector

Check Salt Light

Performa Valve Identification

Injector and Cap

Refill Controller

Check Salt Light

Figure 1

Figure 2

Figure 3

Release Tab

(Chlorine Generator) Outlet

Printed in USA P/N 1268103 Rev B

Step 7

Remove the overlay sticker from the Logix control and

replace with the included new overlay that features the

check salt light opening. The old overlay sticker can be

easily peeled off with a knife or screwdriver.

Summary Chlorine Generator

The chlorine generator feature is constantly checking for

salt and will produce chlorine throughout the regeneration

process. This automatic monitoring system will only

produce chlorine when a salt/regenerant is available in the

brine line.

The chlorine generator will produce up to a maximum of

4 ppm of chlorine. The chlorine generator is not designed

to be used with special medias that require chlorine for

proper application. The chlorine generator provides

chlorine for aesthetic chlorination of media bed.

No Salt Detector

The no salt detector operates like the chlorine generator,

except no chlorine is produced.

The check salt light will illuminate whenever the brine

concentration falls below 5 to 7 salometer point.

NOTE: Ensure that the refill rate of the probe

assembly matches the original refill flow

control assembly.

Questo manuale è adatto per i seguenti modelli

Altri manuali Pentair Unità di controllo

Pentair

Pentair FLECK NXT Manuale utente

Pentair

Pentair Fleck 2850 Manuale utente

Pentair

Pentair FLECK 5810 Manuale utente

Pentair

Pentair FLECK 9100 SXT Manuale utente

Pentair

Pentair F783E Manuale utente

Pentair

Pentair Fleck 5800 XTR Guida utente

Pentair

Pentair Hydromatic Novus 4000 Manuale

Pentair

Pentair Autotrol 255 Series Guida utente

Pentair

Pentair Fleck7000SXT Manuale utente

Pentair

Pentair AURORA CBV-S/A Manuale utente

Pentair

Pentair Goyen Precision P1 Manuale utente

Pentair

Pentair E-Box INTELLIPOOL Istruzioni operative

Pentair

Pentair FLECK 9000 Manuale utente

Pentair

Pentair SUDMO P740 Manuale utente

Pentair

Pentair Raychem PMKG-LE Manuale utente

Pentair

Pentair SIATA V132 SFE-EV VIRIDION Manuale utente

Pentair

Pentair HYPRO PROSTOP-E Manuale utente

Pentair

Pentair AUTOTROL368 Guida utente

Pentair

Pentair FLECK 4600-SXT Guida utente

Pentair

Pentair FLECK 5800 Manuale utente

Pentair

Pentair HYPRO PROSTOP-E Manuale utente

Pentair

Pentair FLECK 5810 XTR2 Manuale utente

Pentair

Pentair FLECK 4600 SXT Manuale utente

Pentair

Pentair Fleck 2850 NXT Guida utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente