PerkinElmer Lambda 365 Manuale utente
09931465A
PerkinElmer, 710 Bridgeport Avenue,
Shelton, CT06484-4794, U.S.A
Produced in the USA.
Lambda 365 Changer 8-Cell for Dissolution Installation
Instructions
This instruction sheet describes the installation of this accessory which is used with the Lambda 365
Spectrophotometer.
NOTE:
Read these instructions before you install this accessory.
Contacting PerkinElmer
Supplies, replacement parts, and accessories can be ordered directly from PerkinElmer, using the part
numbers.
See our website:
http://perkinelmer.com
PerkinElmer's catalog service offers a full selection of high-quality supplies.
To place an order for supplies and many replacement parts, request a free catalog, or ask for information:
If you are located within the U.S., call toll free 1-800-762-4002, 8 a.m. to 8 p.m. EST. Your order will be
shipped promptly, usually within 24 hours.
If you are located outside of the U.S., call your local PerkinElmer sales or service office.
Features
•Suitable size for the standard cells
•Excellent durability
Figure 1 Lambda 365 Changer 8-Cell for Dissolution [P/N: N4104018]
09931465A
2
Dimensions and Specifications
Dimensions
Physical Characteristic Specification Comment
Outline
Height (mm) 140.5
Width (mm) 134.5
Depth (mm) 356.5
Inner
Height (mm) 35
Suitable for the Standard
Cell
Width (mm) 14
Depth (mm) 12.5
Weight (kg) 2.5
Specifications
Physical Characteristic Specification Comment
Space between cells (mm) 10.4
Moving distance of one cell (mm) 11.5
Moving distance of eight cells (mm) 80.5
Moving time of one cell (sec) 1.3
Moving time of eight cells (sec) 8.5
09931465A
3
Configuration of Changer 8-Cell for Dissolution
Figure 2 Changer 8-Cell for Dissolution Configuration
- Used to fix a cell holder, a base plate or a front plate for Lambda 365.
- Spare screws (2 each) are included with the accessory.
Figure 3 Round headscrew with washer (M4 *12L)
Figure 4. Manifold Figure 5. Plate for Calibration
Figure 6. Lid
09931465A
4
Figure 7. Tubings for cell compartment inside (P/N B2000049) and outside
(P/N B2000515)
Figure 8. Flow Cell (N4101052)
NOTE
: Tubings for cell compartment inside (B2000049) and outside (P/N B2000515) and Flow cell
(P/N N4101052) must be purchased separately.
Manifold and tubing connection
1. Prepare a manifold
2. Connect a red connector of the inside tube (P/N B2000049) to the In port of the manifold and
other white connector of the inside tube (short connector) to the flow cell with the arrow mark
(Inlet).
Figure 9. Connecting the inlet tube
09931465A
5
3. Connect a red connector of the inside tube (P/N B2000049) to the Out port of the manifold and
other white connector of the inside tube (long connector) to the flow cell’s outlet port.
Figure 10. Connecting the outlet tube
4. Connect a red connector of the outside tube (P/N B2000515) to the port of the manifold.
Figure 11. Connecting the outside tube
5. Connect all the connectors in the same way.
Figure 12. Manifold and tubing connection
09931465A
6
Installation
1. Prepare the Lambda 365 Spectrophotometer to install this accessory.
2. Connect the power cord and the communication cable. DO NOT turn on the power of the
instrument!
3. Remove the two round head screws with washer (M4*12L) to remove the existing cell holder and
base plate.
Figure 13. Location of the round head screws with washer
4. Pull out the cell holder and base plate by hand.
Figure 14. Pulling out the cell holder and base plate
CAUTION
ATTENTION
Make sure the instrument is turned off while installing this accessory.
Assurez-vous que l’instrument est é
teint lors de l’installation de cet
accessoire.
09931465A
7
5. Insert the Changer 8-Cell for Dissolution in the sample compartment.
Figure 15. Inserting the Changer 8-Cell for Dissolution into the sample compartment
6. Gently press the Changer 8-Cell for Dissolution to connect the communication port (male) under
the bottom of the Changer 8-Cell for Dissolution to the port (female) in the sample compartment.
Figure 16. Connecting the communication ports
09931465A
8
7. Tighten the Changer 8-Cell for Dissolution in the sample compartment with the screws. (The red
circles indicate the location of the screws in the figure).
Figure 17. Tighten the Changer 8-Cell for Dissolution
8. Attach the plate for calibration on the front plate and tighten the 4 bolts.
Figure 18. Tighten the 4 bolts
9. Close the sample compartment cover and turn on the power switch of the instruments.
CAUTION
ATTENTION
Do not start the UV Express software before finishing the initialization of grating.
Ne démarrez pas
le logiciel UV Express avant de terminer l'initialisation du
réseau.
09931465A
9
Measurement
NOTE:
Start the System Self Test after warming up the system for at least 20 minutes.
1. Double-click on the UV Express Software folder and select one of the mode for starting.
2. The following message box will be shown. Empty the cell holder and close the lid firmly. Click OK.
3. System Self Test stars. Click OK after finishing the System Self Test.
4. Select New to open a new window. Select Experiment Type and select OK.
5. Open Method in the main menu.
6. Perform multi-cell calibration according to the ‘Calibration of Multi-Cell Position’ chapter. (p 15)
NOTE:
Calibrate the beam position of the Changer 8-Cell for Dissolution whenever it is installed or beam position
is incorrect.
7. After completing the multi-cell calibration, remove the Plate for Calibration.
Figure 19. Removing the Plate for Calibration
09931465A
10
8. Prepare the manifold with all the tubing connected in Chap. ‘Manifold and tubing connection’ (p4).
Figure 20. Manifold with all the tubing connected
9. Insert the tubes and cells through the front cover first and hold the manifold in place.
Figure 21. Inserting the tubes and cells
10. Tighten the 4 bolts.
Figure 22. Tighten the 4 bolts
Altri manuali per Lambda 365
6
Indice
Altri manuali PerkinElmer Strumento di misura
PerkinElmer
PerkinElmer QuantaSmart 1694267 Manuale utente
PerkinElmer
PerkinElmer Lambda XLS Manuale utente
PerkinElmer
PerkinElmer Lambda 365 Manuale utente
PerkinElmer
PerkinElmer TGA 4000 Istruzioni di montaggio
PerkinElmer
PerkinElmer FX-10 UHPLC Manuale utente
PerkinElmer
PerkinElmer Lambda 465 Manuale utente
PerkinElmer
PerkinElmer LabChip GX Touch Manuale utente
PerkinElmer
PerkinElmer FL 6500 Manuale utente
PerkinElmer
PerkinElmer FL 6500 Manuale utente
PerkinElmer
PerkinElmer LAMBDA 265 Manuale utente
PerkinElmer
PerkinElmer Lambda 20 Manuale del prodotto
PerkinElmer
PerkinElmer LAMBDA 265 Manuale utente
PerkinElmer
PerkinElmer Lambda 365 Fiber Coupling Module Manuale utente
PerkinElmer
PerkinElmer Lambda 11 Manuale utente
PerkinElmer
PerkinElmer DSC 4000 Istruzioni di montaggio
PerkinElmer
PerkinElmer Spectrum 100 Series Manuale utente
PerkinElmer
PerkinElmer LabChip GX Manuale utente
PerkinElmer
PerkinElmer AAnalyst 300 Manuale utente
PerkinElmer
PerkinElmer FL 6500 Manuale utente
PerkinElmer
PerkinElmer L6050002B Manuale utente
