Perle IDS-105F Manuale utente
P/N 5500338-10 (Rev H)
Perle IDS-105F (XT)
Unmanaged 10/100
Ethernet Switches
Installation Guide
- 2 - 105F Installation Guide
Overview
This document contains instructions necessary for the
installation and operation of the Perle IDS-105F Ethernet
switch. This Ethernet switch can be ordered as a 5-port RJ-45
switch or with 4 RJ-45 ports and one SC or ST fiber port. The
fiber port can be either single mode (SM) or multimode (MM)
depending on the model selected and they can operate over
different wavelengths and distances. Visit the Perle website for
the most up to date installation guides, models and
specifications.
http://www.perle.com/
Note: xxxxxxx indicates models numbers for this product line.
TP = twisted pair
XT – Extended temperature models
Features
•10/100Base-TX with one SC/ST fiber port, multi/single mode
•IEEE 802.3/802.3u/802.3x
•10/100, Full/Half duplex, MDI/MDIX with auto-sensing
•Auto-negotiation on copper ports
•Redundant DC power inputs
•Rugged high-strength case
•Industrial temperature models
•Din-rail or wall/panel mounting
Note – In this guide the various models will be referred to as the IDS-
105F
Model
Port 1 - 4
Port 5
IDS-105F TP (RJ-45) TP (RJ-45)
IDS-105F-xxxxxxx TP (RJ-45) Fiber port
IDS-105F-XT
(Industrial Temperature) TP (RJ-45) TP (RJ-45)
IDS-105F-xxxxxxx-XT
(Industrial Temperature) TP (RJ-45) Fiber port
105F Installation Guide - 3 -
Getting to know your IDS-105F Switch
Package Contents:
•IDS-105F
•DIN-rail mounting clip (pre-installed on the unit)
•This guide
Note – Optional panel/wall mounting kits may be ordered
Front View of IDS-105F
(5 port RJ-45)
- 4 - 105F Installation Guide
Front View of IDS-105F (
with one fiber port)
Top view of the IDS-105F
105F Installation Guide - 5 -
Power
The IDS-105F switch has two power inputs that can be
connected simultaneously to DC or AC power sources. If one
power source fails, the other acts as a backup, and
automatically powers the switch.
Reset Button
To reset the IDS-105F insert a paper clip into the air hole vent
and gently press the reset button. The LEDs on the IDS-105F
will go On and then momentarily Off when released to show
that the unit has been reset. All links will be dropped and the
MAC tables will be cleared.
LED Status
P1 / P2– Power (Green LED)
•On: Power present
•Off: No Power present
Fiber Port 5 (Green LED)
•On: Link up
•Flashing: Link up and Ethernet activity detected
•Off: Link down
- 6 - 105F Installation Guide
Ethernet Port Status
Port Link / Speed (Green and Yellow LEDs)
•On: Link Up
•100 Mbps Green on
•10 Mbps Green off
•Flashing: Link up and Ethernet activity detected
•Off : Link down
105F Installation Guide - 7 -
Dimensions for the IDS-105F
- 8 - 105F Installation Guide
105F Installation Guide - 9 -
Mounting the IDS-105F on a DIN-rail
1. The DIN-rail clip will be fixed to the back panel of the IDS-
105F switch when you receive the product.
2. Position the IDS-105F such that the top of the DIN-rail fits into
the slot on the top of the DIN-rail clip, just below the hook and
behind the spring.
3. While pushing down on the unit to compress the spring, rotate
the bottom of the IDS-105F toward the rail. This will snap the
bottom of the rail into the bottom of the clip. See diagram
below
Note: To remove the IDS-105F from the DIN-rail, push down slightly
on the IDS-105F unit while pulling the bottom out.
Wall Mounting the IDS-105F
1. Remove the DIN-rail clip from the rear panel on the IDS-105F.
2. Attach the wall mount plates to the IDS-105F as shown below
using the screws provided in the kit.
- 10 - 105F Installation Guide
3. Use the wall mount plates as a guide to mark the spots where
the screws will be.
4. Drive the screws into the wall leaving about 2 mm of the screw
protruding from the wall to allow room for sliding the wall
mount panel between the wall and the screws.
5. Once the screws are fixed to the wall, insert the four screw
heads through the large part of the keyhole shaped screw
openings.
6. Pull the IDS-105F down to lock the IDS-105F to the wall
mount.
7. Tighten the four screws securely to the wall.
Note: For the best results use screws that have the following attributes:
Head diameter .5 - .6 mm
Shaft diameter 3 - 3.5 mm
Wall/Panel Mounting
Note: the dimensions are in mm
Indice
Altri manuali Perle Interruttore
Perle
Perle IDS-509G Manuale utente
Perle
Perle IDS-105FE Series Manuale utente
Perle
Perle IDS-409 Manuale utente
Perle
Perle IDS-509C Manuale
Perle
Perle IDS-206 Manuale
Perle
Perle IDS-409C Manuale utente
Perle
Perle IOLAN STS8D GR Manuale
Perle
Perle IDS-710HP Manuale
Perle
Perle IDS-710HP Manuale utente
Perle
Perle IDS-409G Manuale utente
Perle
Perle IDS-205F Manuale utente
Perle
Perle IDS-305G Manuale utente
Perle
Perle IDS-108FPP series Manuale utente
Perle
Perle IDS-509GPP Manuale utente
Perle
Perle IDS-409-SFP Manuale
Perle
Perle IDS-205G Manuale utente
Perle
Perle IDS-409-SFP Manuale utente
Perle
Perle IDS-1 HP Series Manuale utente
Perle
Perle IDS-509G Manuale
Perle
Perle IDS-509FPP Manuale
