Philips 100WT10P Manuale utente
1 Before You Begin
1.1 Introduction
1.2 Packing list
1.3 Physical appearance
2 Getting Started
2.1 Base station setup
2.2 Load battery
2.3 Get ready
2.4 Stylus
2.5 WLAN setup
3 Power Supply
3.1 AC
3.2 Battery
4 Data input to the touch screen
4.1 Stylus
4.2 On-screen keyboard
5 Connecting to network
5.1 WLAN
5.2 LAN
6 Data Synchronization
6.1 USB
6.2 IR
7 Featured Software Application
7.1 Control Panel
7.2 Internet Explorer
7.3 ActiveSync
7.4 Citrix ICA Client
7.5 Microsoft RDP
7.6 Windows Media Player
7.7 Transcriber
7.8 Hot Key Utility
7.9 VGA Utility
7.10 Registry Utility
7.11 Word Pad
8 Troubleshooting
9 Safety and product care instructions
10 Appendix
A: Specifications
B: I/O Interfaces
C: Proprietary notice and liability disclaimer
D: Regulatory Information
TABLE OF CONTENTS
1
1.1 Introduction
You are about to experience the new Philips 100WT10P.Your 100WT10P speeds up data sharing and
delivers the right data at the right time, increasing productivity for people like you who need timely data.
100WT10P features a 10.4inch touch-sensitive LCD display, embedded Microsoft RDP and Citrix ICA
Client, built-in 802.11b WLAN and rugged hardware design. Use of thin clients such as the 100WT10P can
reduce total administrative costs and add to bottom line efficiency by speeding up business processes. With
modular design, the 100WT10P can be easily customized for industry or site-specific applications or needs.
This manual will guide you through 100WT10P simple set-up, introduce you to its range of features and
help you source extra information.
1.2 Packing list
The 100WT10P carton contains the following items:
1. 100WT10P pad 4.AC power adaptor 7. Mini VGA cable
2. Base station 5. Stylus X 2 8. Companion CD
3. Battery 6. Mini USB B to A cable 9. Quick Start Guide
1 BEFORE YOU BEGIN
1 4 7
2 5 8
3 6 9
2
1 BEFORE YOU BEGIN
1.3 Physical Appearance
Right View
1. External ear set jack
2. External microphone jack
3. USB port type A
4. USB port type A
5. USB mini type B
6. COM port
7. Mini VGA
8. & 9. Nut screw holes
Left View
1. Infrared port
2. Stylus pen
3. PCMCIA type II
4. Power On/Off switch
5. DC-in jack
6. & 7. Nut screw holes
Bottom
1. Docking connector to the base station
Back
1. Modular connector (supports COM, PCI,
USB1.1 host)
2. Cover for Flash memory and coin battery
3. Battery Latch 1
4. Battery Latch 2
5. Speaker
6. Battery
7. Software/hardware preset
8.Wireless power switch
5
6
3
4
8 7
3 4 5 6
7
3
Front View
1. Power LED indicator
2, 3, 5, and 6 Customized hot key
4. Four-way directional key with enter
7. Input panel button
8. Internal microphone
9.WLAN LED Indicator
Base Station
1. 2x USB port (type A)
2. Power LED Indicator
3. Docking site
Mini-VGA to VGA Cable
The Mini-VGA cable
allows you to connect
to a standard VGA cable
for connection to a monitor
display terminal or
projector.
Ruggedized Design
Your 100WT 10P is specially designed to withstand such as a physical impact or a liquid spill.
1. Drop resistant.
It has the anti-shock design to resistant to 3 feet drop test
2. Liquid spill.
100WT10P meets the IP53 requirement for water and dust resistance.
1 BEFORE YOU BEGIN
3
3
4
5
6
7
8
9
4
2 GETTING STARTED
2.1 Base station setup
2.1.1. Connect power cord to the AC power adaptor.
2.1.2. Plug the cord into the base station first and then plug the other end into a power outlet.
2.2 Load battery
2.2.1. Make sure the power switch at lower-left corner of your 100WT10P is in the OFF position.
2.2.2. Install the battery.
1. Place 100WT10P on your desk with its face down.
2. Place the battery in the battery slot then press it down to fit in.
3. Push battery latch 1 into the locked position.
4. For first time use, the battery requires five hours to become fully charged.
2.3 Stylus recalibration
When the pad is powered on for the first time, the recalibration protocol will automatically launch.
Follow the instructions to walk through the process.
2.4 WLAN setup
1.Tap START
2.Tap SETTINGS
3.Tap Network and Dial-up Connections
4.Tap 'Internal Wireless LAN' Settings icon
5. A dialog box pops up. Choose the Wireless Networks tab.Tap the Refresh button in the
Available Networks panel. In a few seconds, a list of available networks is displayed
6. Select the network to which you wish to connect
7.Tap CONFIGURE
8.Tap OK
5
3 POWER SUPPLY
There are two sources of power for 100WT10P operation: the battery and the AC adapter.
3.1 AC
You may operate your 100WT10P with AC power in two different ways. Mounted in the base station, or
connected directly to the AC adapter.To run your 100WT10P on the base station, place the pad into and
connect the AC adapter to the jack at the rear of the base station.To plug the product directly to the AC
adapter, locate and plug into the DC-in jack at the lower left corner of the product, under the orange
rubber protector.
3.2 Battery
3.2.1. When using the 100WT10P for the first time, it is advisable to charge the battery for at least 5
hours.
3.2.2. After the initial charging, when not in use, the 100WT10P takes approximately two hours to fully
charged; it takes 3 hours to fully charged while in use.A fully charged battery lasts up to 4 hours.
3.2.3. The power light on the top right indicates the level of battery charge.
Turn on the power to see the power light.
Full charge The power light is solid green.
Low charge The power light is blinking green when the battery's remaining charged falls to less
than 6 percent.
Critical low charge The power light blinks amber when the charge falls under 3 percent.
If your 100WT10P is powered up and immediately enters the suspend mode, it means the
battery is uncharged.To avoid loss of data in memory, fully charge the unit within 24 hours.
CAUTION: Recharge the 100WT10P any time a low charge warning appears.
Failure to recharge the battery will result in loss of data contained in internal memory (RAM).
3.2.4. In order to optimize battery operation, open only the applications you are actually using.
To conserve battery power, disable WLAN when it's not in use.
3.2.5. To change battery
1. Suspend your 100WT10P by turning the power switch to the OFF position.
2. Unlock the battery latch 1
3.While one hand holds the battery latch two in the unlocked position, use the other hand to pull
the battery out of the slot.
4. Replace with another battery
NOTE: When fully charged and not in use, your 100WT10P has a life of one week.
CAUTION:
1. Suspend your 100WT10P before removing or changing the battery pack.
2.To avoid loss of data in memory, insert a charged battery in 24 hours.
6
3.2.6. Power saving
Power saving is available when your 100WT10P is idle.There are three levels of power saving.
Level 1. User idle: lower screen light
Level 2. System idle: off screen light
Level 3. Suspend: power off to suspend
To make changes to power saving setup,
Tap START
Tap SETTINGS
Tap CONTROL PANEL
Tap POWER
Choose SCHEMES and select the scheme that best meets your needs.
3 POWER SUPPLY
7
4 DATA INPUT TO THE TOUCH SCREEN
You can use the stylus or the internal keyboard to select menu options and write messages.
4.1 Stylus
The stylus is used to tap or for handwriting input.When the system turns on for the first time, it
defaults to tap input.
NOTE: The two styli that are supplied with 100WT10P are designed for your screen. Use of fingertip or
other pointers could damage your screen.
4.1.1 Handwriting
Transcriber is the software application for handwriting input.
To start this application, double-tap on the TRANSCRIBER icon or,
1. Tap SETTINGS
2. Tap PROGRAMS
3. Tap TRANSCRIBER
4. When operating, the Transcriber icons will reside in the
system tray located at the bottom of the screen.
To close Transcriber,
1. Go to the system tray at the bottom of screen
2. Double tap on the Transcriber icon for menu options
3. Choose CLOSE TRANSCRIBER
8
4.1.2 Tap settings
You can use the stylus to tap or double-tap.
Each user's tapping pattern is different.The 100WT10P system
setup process 'learns' each new user's tapping pattern 'signature'.
To test your double-tap pattern:
1.Tap START
2.Tap SETTINGS
* Tap CONTROL PANEL
3. Double tap STYLUS
4. Choose the DOUBLE-TAP
5. Follow the onscreen instructions
To recalibrate the stylus tapping pattern:
1.Tap START
2. Tap SETTINGS
3. Tap CONTROL PANEL
4. Double tap STYLUS
5. Choose the CALIBRATION
6.Tap RECALIBRATION
7. Follow the onscreen instructions
4 DATA INPUT TO THE TOUCH SCREEN
Altri manuali per 100WT10P
1
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Philips Server
