Planet ICS-2100T Manuale utente
Industrial 1-/2-/4-port RS232/422/485
Serial Device Server Series
ICS-2100T/ICS-2105AT/ICS-2200T/ICS-2400T
Quick Installation Guide
Table of Contents
1. Package Contents...................................................................... 3
2. Requirements............................................................................ 4
3. Hardware Introduction ............................................................... 5
3.1 Front Panels ....................................................................... 5
3.2 Wiring the Power Inputs...................................................... 6
3.3 Serial Port PIN Assignment .................................................. 7
4. Web Login ................................................................................ 8
4.1 Starting Web Management................................................... 8
4.2 Logging in to the Industrial Serial Server.............................. 8
5. Remote Telnet Login .................................................................10
5.1 Logging in to the Remote Command Line Interface...............10
6. Getting Started with VCOM Utility ..............................................11
6.1 Installation of VCOM Utility .................................................11
6.2 Searching Serial Device Server ...........................................12
6.3 Serial Server Login ............................................................12
6.4 Serial Server Setting..........................................................13
6.5 COM Port Mapping .............................................................14
7. RecoveringBacktoDefaultConguration ...................................15
8. Customer Support ....................................................................16
3
1. Package Contents
Thank you for purchasing PLANET Industrial Serial Device Servers. The
table below shows the models with the number of serial ports:
Model Name Serial Port Ethernet Port Power Input DI/DO
ICS-2100T 1 x DB9 +
1 x 4-pin
terminal block
1 x 10/100TX RJ45 DC 9~48V
or AC 24V
-
ICS-2105AT 1 x 100FX SFP -
ICS-2200T 2 x DB9 2 x 10/100TX RJ45 DC 12~48V -
ICS-2400T 4 x DB9
“Industrial Serial Server” is used as an alternative name in this
Quick Installation Guide.
Open the box of the Industrial Serial Server and carefully unpack it.
The box should contain the following items:
The Industrial Serial Server x 1 Quick Installation Guide x 1
Wall Mounting Kit x 1 Dust Cap
(RJ45/SFP)
DIN-rail Bracket
w/Screws x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
4
2. Requirements
The Industrial Serial Server provides remote login interface for
management purposes. The following equipment is necessary for
further management:
Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC
OS X or later, Linux, UNIX, or other platforms are compatible with
TCP/IP Protocols.
Ethernet Port Connection
Workstations are installed with Ethernet NIC (Network Interface
Card)
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
Use standard network (UTP) cables with RJ45
Use Multi-mode or Single-mode ber patch cord with LC
connector and 100BASE-FX SFP transceiver (ICS-2105AT only).
The above PC is installed with Web browser
Note
It is recommended to use Internet Explorer 8.0 or above
to access the Industrial Serial Server.
Note
If the Web interface of the Industrial Serial Server is not
accessible, please turn off the anti-virus software or fire-
wall and then try it again.
5
3. Hardware Introduction
3.1 Front Panels
ICS-2100T ICS-2105AT ICS-2200T ICS-2400T
PWR1 PWR2 Fault
Reset
LNK/
ACT
Rx Tx
10/100TX
RS232
ICS-2100T
TxD+
RxD+
RS422/485
PWR1 PWR2 Fault
Reset
LNK/
ACT
Rx Tx
100FX
SFP
RS232
ICS-2105AT
TxD+
RxD+
RS422/485
PWR1 PWR2 Fault
SYS
E2
E1
LNK/
ACT
LNK/
ACT
Rx Tx
Rx Tx
P1
P2
RS232/422/485
P1
P2
ICS-2400T
E2
E1
P1 P3
PWR1 PWR2
I/O
Fault
P1
Rx Tx Rx Tx
Rx Tx Rx Tx
SYS
LNK/
ACT
LNK/
ACT
P3
P2 P4
P2
RS232/422/485
P4
6
3.2 Wiring the Power Inputs
The upper panel of the Industrial Serial Server indicates a DC inlet
power socket and consists of one terminal block connector within 6
contacts. Please follow the steps below to insert the power wire.
1. Insert positive/negative DC power wires into Contacts 1 and 2 for
Power 1, or Contacts 5 and 6 for Power 2. Figures 3-1 to 3-3
show PWR1 and PWR2 of the Industrial Serial Server.
ICS-2100T/ICS-2105AT: 9~48V DC or 24V AC
V1+ V2+ V2
PWR1 PWR2Fault
Max. fault loading: 24V, 1A
DC Input: 9-48V
, 1A max.
AC Input: 24V
, 0.5A max.
1 2 3 4 5 6
Figure 3-1: ICS-2100T/ICS-2105AT Upper Panel
ICS-2200T: 12~48V DC
V1+ V1- V2+ V2-
PWR1 PWR2Fault
DC Input:
12-48V , 1Amax.
1 2 3 4 5 6
Figure 3-2: ICS-2200T Upper Panel
1A@24V
V1+ V1- V2+ V2-
PWR1 PWR2Fault
DI1 DO0 DO1DI0 GNDGND
DC Input:
12-48V , 1Amax.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-3: ICS-2400T Upper Panel
7
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
1 2 3 4 5 6
V1+ V1- V2+ V2-
Power 1 Fault Power 2
Figure 3-4: PWR1 & PWR2 Pins of Terminal Block.
Note
The wire gauge for the terminal block should be in the
range from 12 to 24 AWG.
3.3 Serial Port PIN Assignment
8
4. Web Login
4.1 Starting Web Management
The following shows how to start up the Web Management of the
Industrial Serial Server. Note the Industrial Serial Server is congured
through an Ethernet connection. Please make sure the manager PC
must be set to the same IP subnet address.
For example, the default IP address of the Industrial Serial Server is
192.168.0.100, then the manager PC should be set to 192.168.0.x
(where x is a number between 1 and 254, except 100), and the
default subnet mask is 255.255.255.0.
Ethernet
PC/Workstation with Web Browser
IP Address:192.168.0.x
RJ45 UTP Cable
ICS Serial Device Server
IP Address:192.168.0.100
Figure 4-1: IP Management Diagram
4.2 Logging in to the Industrial Serial Server
1. Use Internet Explorer 8.0 or above for Web browser and enter IP
address http://192.168.0.100 (the factory-default IP address) to
access the Web interface.
2. When the following dialog box appears, please enter the default user
name “admin” and password “admin” (or the password you have
changed before) as shown in Figure 4-2.
Default IP Address: 192.168.0.100
Default User Name: admin
Default Password: admin
Figure 4-2: Login Screen
9
3. After entering the password, the main screen appears as shown in
Figure 4-3.
Figure 4-3: Web Main Screen of Industrial Serial Server
4. The Server Menu on the middle of the Web page lets you access all
the functions and statuses the Industrial Serial Server provides.
Now, you can use the Web management interface to continue the
Serial Server management. Please refer to the user manual for more.
Note
1. For security reason, please change and memorize
the new password after this first setup.
2. Only accept command in lowercase letter under web
interface.
10
5. Remote Telnet Login
5.1 Logging in to the Remote Command Line Interface
The Industrial Serial Server also supports Telnet for remote
management. You can use Telnet to open a terminal session over
one of the Ethernet ports. The Serial Server asks for user name and
password for remote login when using Telnet; please use the following
defaultIPaddress,usernameandpasswordfortherst-timelogin.
Default IP Address: 192.168.0.100
Default Username: admin
Default Password: admin
You will be presented with a text menu displaying the Industrial Serial
Server’s general settings, which you will be able to view and modify.
Please refer to User Manual for a description of the available settings.
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Planet Server
Planet
Planet IVS-110 Manuale utente
Planet
Planet NAS-7103 Manuale utente
Planet
Planet ICS-2102ST Manuale utente
Planet
Planet ICS-2200T Manuale utente
Planet
Planet ICS-11 Series Manuale utente
Planet
Planet SIP-50 Manuale utente
Planet
Planet IVS-H125 Manuale utente
Planet
Planet NAS-1000 Manuale utente
Planet
Planet NAS-1101 Manuale utente
Planet
Planet 2-Bay SATA NAS RAID Server NAS-7200 Manuale utente
Planet
Planet NAS-7102 Manuale utente
Planet
Planet NAS-7400 Manuale utente
Planet
Planet IVS-100 Manuale utente
Planet
Planet NAS-7101 Manuale utente
Planet
Planet NAS-3410 Manuale utente
Planet
Planet 1-Bay SATA NAS Server NAS-7100 Manuale utente
Planet
Planet IVS-H120 Manuale utente
Planet
Planet NAS-7202 Manuale utente
Planet
Planet NAS-7410 Manuale utente
Planet
Planet 1-Bay SATA NAS Server NAS-7100 Manuale utente
