Power Probe 3EZ Manuale utente
Power Probe 3EZ
INTRODUCTION
Thank you for purchasing the Power Probe 3EZ (PP3EZ). The
PP3EZ includes all the powerful testing modes and features
of the Power Probe 3S plus now includes 2 new modes - EZ
Learning Mode and EZ Diagnostics Mode. The PP3EZ speeds
you through the diagnosing of 12 to 24 volt automotive elec-
trical systems. After connecting the PP3EZ’s clips to the ve-
hicle’s battery, the automotive technician can determine at a
glance, the voltage level and the polarity of a circuit without
running for a voltmeter or reconnecting hook-up clips from
one battery pole to the other. The power switch allows the
automotive technician to conduct a positive or negative bat-
tery current to the tip for activating and testing the function of
electrical components without wasting time with jumper leads.
WWW.POWERPROBETEK.COM
5000815
It allows you to follow and locate short circuits without wasting
precious fuses. The Power Probe can also test for continuity
with the assistance of its auxiliary without running to the bat-
tery as you would otherwise have to do with simple test lights.
The PP3EZ’s 20ft (extendable) cable allows you to test along
the entire length of the vehicle without constantly searching
for ground hook-ups.
Do not use the equipment for measurements on CAT II, CAT
III & CAT IV. An absolute must for every automotive technician
looking for a fast and accurate solution to electrical systems
diagnostics.
Before using the Power Probe 3EZ please read the instruction
booklet carefully.
If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may
be impaired.
Warning! When the PP3EZ rocker switch is depressed bat-
tery current/voltage is conducted directly to the tip which
may cause sparks when contacting ground or certain circuits.
Therefore the power energized Power Probe could ignite
these vapors. Use the same caution as you would when using
an arc welder.
WWW.POWERPROBETEK.COM
2
INTRODUCTION CONTINUED
Product is not water resistant, please avoid water contact
during operation.
If the test leads need to be replaced, you must use a new one
which should meet EN 61010-031 standard.
The Power Probe 3EZ is NOT to be used with 110/220V
HOME electrical, it is only for use with 12-24V systems.
The Power Probe 3EZ Conforms to UL STD. 61010-1, 61010-2-
030 and 61010-031; Certified to CSA STD. C22.2 NO. 61010-1,
61010-2-030 and 61010-031.
To switch languages on the PP3EZ, with the hook up clips re-
moved from the battery, press and hold the right button. While
holding the right button, attach the hook up clips to the bat-
tery power. The language options will appear on the screen.
Choose the desired language by pressing the left button.
Press the right button to set the language.
WWW.POWERPROBETEK.COM
3
INTRODUCTION CONTINUED
WWW.POWERPROBETEK.COM
4
TABLE OF CONTENTS
Hook-up and quick self-test 5
Turning the Audio Tone On & O 5
Circuit Breaker 5
Voltage & Polarity testing 5
Continuity testing 6
Introduction to “EZ” 7
Guided Diagnostics 8
Testing Section 9
Continuity Testing 10
Activating components in hand 11
Testing trailer lights and connections. 13
Activating electrical components in the Vehicle 14
Activating electrical components with Ground 16
Checking for bad ground contacts 18
Following & Locating Short Circuits 19
Red/Green Indicator & Audio Tone 19
Flip Screen Function 19
Modes 20
Specifications 27
Replacement Parts 29
Power Probe warranty 29
Power Probe TeK Contact Details Back Cover
IMPORTANT TIP: When powering-up components, you can in-
crease the life of your Power Probe switch if you first press the
switch, then contact the tip to the component. The arcing will
take place at the tip instead of the contacts of the switch.
Unroll the Power Probe cable. Connect the RED battery hook-
up clip to the POSITIVE terminal of the vehicle’s battery. Con-
nect the BLACK battery hook-up clip to the NEGATIVE termi-
nal of the vehicle’s battery. When the PP3EZ is first connected
to a battery (power source), it will sound a quick start up tone
and then go into Voltmeter Mode (See Mode #1) and the 2
bright white LEDs (dual headlights) will be on to illuminate the
test area of the probe tip.
WWW.POWERPROBETEK.COM
5
HOOK UP AND QUICK SELF-TEST
TURNING AUDIO TONE ON & OFF
While the PP3EZ is in Voltmeter Mode, press the left button to
toggle the tone on or o. When the left button is pressed, if a
short high beep is heard, this means the audio tone is turned
on. If a short low beep is heard, the audio tone has turned o.
WWW.POWERPROBETEK.COM
6
TURNING AUDIO TONE ON & OFF
In Voltmeter Mode (Mode #1) with the circuit breaker tripped,
the display will show “Circuit Breaker Tripped”(see page 11-12
for detail) All other functions of the PP3EZ are still active. This
means that you can still probe a circuit and observe the volt-
age reading. When the circuit breaker is tripped, the PP3EZ
will NOT be able to conduct battery current to the tip even
when the power switch is pressed. Intentionally tripping the
breaker and using the PP3EZ to probe can be considered an
added precaution against accidental pressing of the power
switch.
CIRCUIT BREAKER
WWW.POWERPROBETEK.COM
7
INTRODUCTION TO “EZ”
The Power Probe 3EZ is the latest addition to the Power
Probe line of circuit testers. It includes all the powerful testing
modes and features of the Power Probe 3S and now includes
2 new modes- EZ Learning Mode and EZ Diagnostics Mode.
EZ Learning Mode will guide you through a step by step
familiarization of the PP3EZ, showing you how to operate the
PP3EZ and how the probe responds in certain testing condi-
tions.
EZ Diagnostics Mode will help guide you through specific
vehicle or component tests and let you know if readings ob-
tained are acceptable or outside of the desired specification.
EZ Learning Mode – Scroll the Menu down using the Left
Button until EZ LEARNING is highlighted on the menu. Select
EZ LEARNING by pressing the Right Button. EZ Learning will
now take you through a step by step process illustrating how
the probe responds and the dierent types of readings that
can be obtained. This mode is to be used for familiarization
and guidance only and is not a mode used for actual circuit
testing.
Once EZ LEARNING mode is selected, it must be scrolled
through from start to finish before it will exit EZ LEARNING
mode. You can also exit EZ Learning by disconnecting pow-
er from the probe and the probe will enter normal test mode
when re-connected. NOTE: If you see a flashing screen in the
menu it means go to that selection and press enter.
EZ Diagnostic Mode – Scroll the Menu down using the Left
Button until EZ DIAGNOSTICS is highlighted on the menu. Se-
lect EZ DIAGNOSTICS by pressing the Right Button. EZ DIAG-
NOSTICS are preset test modes for dierent vehicle system
tests.
The available tests listed are: Battery Check, Charge Test,
Fuse Test, Voltage Test, Component Test, 5V Ref.
Each test section includes a readable QR code that will ac-
cess online video content explaining the test procedure.
5V REF mode is used together with the Power Probe Tek 5V
Adapter Tip (# PPT5VA). With the Adapter Tip installed on the
probe and applying power, the probe will no longer output full
battery voltage. The 5 Volt Adapter will only output a current
limited 5V that can be used as a reference voltage to safely
power and test sensor and computer circuits.
FOR FULL EXPLANATIONS OF EACH TESTING MODE AND
SCREEN PLEASE GO TO:
www.powerprobetek.com/ezdiagnostics/ or scan the below
QR code:
WWW.POWERPROBETEK.COM
8
EZ DIAGNOSTICS
Continuity testing 10
Activating components out of vehicle’s electrical system 11
Testing trailer lights and connections. 13
Activating electrical components in the Vehicle 14
Activating electrical components with Ground 16
Checking for bad ground contacts 18
Following & Locating Short Circuits 18
WWW.POWERPROBETEK.COM
9
TESTING SECTION
WWW.POWERPROBETEK.COM
10
CONTINUITY TESTING
While the PP3EZ is in Voltmeter Mode, and by using the Pow-
er Probe tip in connection with chassis ground or the auxiliary
ground lead, continuity can be tested on wires and compo-
nents attached or disconnected from the vehicle’s electrical
system.
The PP3EZ indicates continuity using 2 resistance levels.
When the Power Probe tip has a resistance to ground less
than 20K Ohms but greater than approx. 650 Ohms the LCD
will indicate “00.0” volts but no Green “-” LED. But when the
resistance to ground less than approx. 650 Ohms the LCD will
indicate “00.0” volts and also the Green “-” LED. The higher
resistance continuity function is useful for checking Spark Plug
Wires, (disconnected from ignition) Solenoids and magnetic
pickup coils, and the lower resistance continuity for testing re-
lay coils and wiring. However the best way to prove continuity
of connections to either Ground or Battery is to power up the
connection using the Power Switch. If the Circuit Breaker trips
you know that you have a good solid low resistance connec-
tion.
Indice
Lingue:
Altri manuali Power Probe Strumento di misura
